Dentin Sealing and Bond Strength Evaluation of Hema-Free and Multi-Mode Adhesives to Biomodified Dentin

Abstract This study evaluated the effect of dentin biomodification on the bond strength (BS) and sealing ability (SA) of HEMA-free and multi-mode adhesives after 24 h and 6 months of water storage. Four adhesives were tested: two multi-mode (Scotchbond Universal - SU, and Prime & Bond Elect - PB) and two HEMA-free (All-Bond 3 - AB, and G-Aenial - GA). Human third molars were selected and dentin was treated with two cross-linking agents (5% glutaraldehyde and 6.5% proanthocyanidin-rich grape seed extract - PACs) for 10 min or kept untreated (control group) (n=6). Teeth were sectioned and prepared for BS test and SA analysis. The SA measurements were taken with the presence of smear layer (minimum permeability), EDTA treatment (maximum permeability), PACs application, adhesive application and after 6 months of water storage. BS data were analyzed by Proc Mixed and Tukey-Kramer test (α=5%). PACs application increased the BS for all adhesives tested at 24 h. However, BS decreased for SU and AB after six months. In general, multi-mode adhesives (SU and PB) did not differ from AB HEMA-free. GA presented the lowest BS values at both times of evaluation. Dentin permeability was reduced after PACs application and remained the same after 6 months, regardless adhesive application. PACs can increase the BS regardless the type of adhesive, however only for PB and GA the BS kept stable after 6-months of water storage. PACs was able to seal the dentin as the minimum permeability and also remained stable after 6 months.

Resumo Este estudo avaliou o efeito da biomodificação da dentina na resistência de união (BS) e capacidade de selamento (SA) de adesivos "HEMA-free" e "multi-mode" após 24 horas e 6 meses de armazenamento em água. Quatro adesivos foram testados: dois "multi-mode" (Scotchbond Universal - SU, e Prime & Bond Elect - PB) e dois "HEMA-free" (All-Bond 3 - AB, e G-Aenial - GA). Terceiros molares humanos foram selecionados e a dentina desses dentes foi tratada com dois agentes "cross-linking" (glutaraldeído 5% e extrato de uva contendo proantocianidina 6.5% - PACs) por 10 min ou permaneceram sem tratamento (grupo controle) (n=6). Os dentes foram seccionados e preparados para teste de BS e análise de SA. As mensurações de SA foram adquiridas com a presença de "smear layer" (mínima permeabilidade), tratamento com EDTA (máxima permeabilidade), aplicação dos PACs, aplicação de adesivo e após 6 meses de armazenamento em água. Os dados de BS foram analisados pelo Proc Mixed e teste de Tukey-Kramer (α=5%). A aplicação dos PACs aumentaram a BS para todos os adesivos testados no tempo de 24 h. Entretanto, a BS reduziu para o adesivo SU e AB após 6 meses. Em geral, os adesivos "multi-mode" (SU e PB) não diferiram do AB "HEMA-free". O adesivo GA apresentou o menor valor de BS em ambos tempos de avaliação. A permeabilidade dentinária foi reduzida após a aplicação dos PACs e permaneceu a mesma até 6 meses, independente da aplicação do adesivo. Os PACs podem aumentar a BS independente do tipo de adesivo, entretanto somente para o adesivos PB e GA a BS manteve estável após 6 meses de armazenamento em água. Os PACs foram capazes de selar a dentina como a permeabilidade mínima da dentina, que permaneceram estável após 6 meses.

Effectiveness of plant-derived proanthocyanidins on demineralization on enamel and dentin under artificial cariogenic challenge

Dental caries is considered a disease of high prevalence and a constant problem in public health. Proanthocyanidins (PAs) are substances that have been the target of recent studies aiming to control or treat caries. Objective The aim of this in vitro study was to evaluate the efficacy of a treatment with grape seed extract, under cariogenic challenge, to minimize or even prevent the onset of caries in the enamel and dentin. Material and Methods Blocks of enamel and dentin (6.0x6.0 mm) were obtained from bovine central incisors, polished, and selected by analysis of surface microhardness (SH). The blocks were randomly divided into 3 groups (n=15), according to the following treatments: GC (control), GSE (grape seed extract), GF (fluoride – 1,000 ppm). The blocks were subjected to 6 daily pH cycles for 8 days. Within the daily cycling, the specimens were stored in buffered solution. The blocks were then analyzed for perpendicular and surface hardness and polarized light microscopy. Results The means were subjected to statistical analysis using the ANOVA and Fisher's PLSD tests (p<0.05). For enamel SH, GF showed the highest hardness values. In the dentin, GF was also the one that showed higher hardness values, followed by GSE. Regarding the cross-sectional hardness values, all groups behaved similarly in both the enamel and dentin. The samples that were treated with GSE and fluoride (GF) showed statistically higher values than the control. Conclusion Based on the data obtained in this in vitro study, it is suggested that grape seed extract inhibits demineralization of artificial carious lesions in both the enamel and dentin, but in a different scale in each structure and in a smaller scale when compared to fluoride. .

Radiant exposure effects on physical properties of methacrylate - and silorane-composites

AIM: To evaluate the effect of different radiant exposures on the degree of conversion (DC), Knoop hardness number (KHN), plasticization (P), water sorption (WS), and solubility (S) of different monomer resin-based composites. METHODS: Circular specimens (5 x 2 mm) were manufactured from methacrylate and silorane composite resins, and light-cured at 19.8, 27.8, 39.6, and 55.6 J/cm2, using second-generation LED at 1,390 mW/cm2. After 24 h, DC was obtained using a FT-Raman spectrometer equipped with a Nd:YAG laser, KHN was measured with 50-g load for 15 s, and P was evaluated on the top and bottom surfaces by the percentage of hardness reduction after 24 h immersed in absolute alcohol. WS and S were determined according to ISO 4049. Data were subjected to statistical analysis (α=0.05). RESULTS: Methacrylate material presented higher DC, KHN, P, and WS than silorane (p<0.05). There was no difference in the S values (p>0.05). The increased radiant exposures improved only the KHN (p<0.05). In general, top surfaces showed higher DC and KHN than bottom, for both materials (p<0.05). The increase of the radiant exposure did not improve most physical properties of the composites and were monomer-base dependent. CONCLUSIONS: Chemical composition of the composite resins resulted in different physical properties behavior and could affect the clinical longevity of dental restorations, but overall these properties were not influenced by the different radiant exposures evaluated in the study...

Impact of light-curing time and aging on dentin bond strength of methacrylate- and silorane-based restorative systems

AIM: To evaluate the impact of different light-curing times on dentin microtensile bond strength of two restorative systems after 24 h and 6 months of water storage. METHODS: Standardized Class II preparations were performed in 56 freshly-extracted human molars (n = 7), restored with methacrylate- or silorane-based restorative systems, and light-cured using a light-emitting diode at 1390 mW/cm2 by the recommended manufacturers' time or double this time. After storage for 24 h at 37 oC, the teeth were sectioned to yield a series of 0.8-mm thick slices. Each slab was trimmed into an hourglass shape of approximately 0.64 mm2 area at the gingival dentin-resin interface. Specimens were tested using universal testing machine at crosshead speed of 0.5 mm/min until failure, after 24 h and 6 months of storage. Data were statistically analyzed by three-way ANOVA and Tukey's test (α = 0.05). RESULTS: The highest bond strength values were recorded for the groups restored with methacrylate system (p<0.001) as well as for extended light-curing time (p = 0.0034). There was no statistically significant difference between 24 h and 6 months storage on bond strength (p>0.05). CONCLUSIONS: Bond strength was influenced by the material and light-curing time, but the 6-month storage did not affect the bond strength of restorations...

Effect of bleaching on sound enamel and with early artificial caries lesions using confocal laser microscopy

The aim of this study was to evaluate effect of bleaching agents on sound enamel (SE) and enamel with early artificial caries lesions (CL) using confocal laser scanning microscopy (CLSM). Eighty blocks (4 x 5 x 5 mm) of bovine enamel were used and half of them were submitted to a pH cycling model to induce CL. Eight experimental groups were obtained from the treatments and mineralization level of the enamel (SE or CL) (n=10). SE groups: G1 - unbleached (control); G2 - 4% hydrogen peroxide (4 HP); G3 - 4 HP containing 0.05% Ca (Ca); G4 - 7.5% hydrogen peroxide (7.5 HP) containing amorphous calcium phosphate (ACP). CL groups: G5 - unbleached; G6 - 4 HP; G7 - 4 HP containing Ca; G8 - 7.5 HP ACP. G2, G3, G6, G7 were treated with the bleaching agents for 8 h/day during 14 days, while G4 and G8 were exposed to the bleaching agents for 30 min twice a day during 14 days. The enamel blocks were stained with 0.1 mM rhodamine B solution and the demineralization was quantified using fluorescence intensity detected by CLSM. Data were analyzed using ANOVA and Fisher’s tests (α=0.05). For the SE groups, the bleaching treatments increased significantly the demineralization area when compared with the unbleached group. In the CL groups, no statistically significant difference was observed (p>0.05).The addition of ACP or Ca in the composition of the whitening products did not overcome the effects caused by bleaching treatments on SE and neither was able to promote remineralization of CL.

O objetivo deste estudo foi avaliar o efeito de agentes clareadores no esmalte sadio (ES) ou esmalte com lesão inicial de cárie artificial (LC), utilizando microscopia confocal laser de varredura (CLSM). Oitenta blocos (4 x 5 x 5 mm) de esmalte bovino foram usados, sendo que 40 destes foram desmineralizados com ciclagem de pH para induzir a LC. Oito grupos experimentais foram obtidos a partir dos tratamentos e condição do esmalte (ES ou LC), com n=10: Grupos ES: G1 - sem tratamento (controle); G2 - peróxido de hidrogênio 4% (PH4); G3: PH4 contendo 0,05% cálcio (Ca); G4 - peróxido de hidrogênio 7,5% (pH 7,5) contendo fosfato de cálcio amorfo (ACP). Grupos LC: G5 - não clareado; G6 - pH 4; G7 - pH 4 Ca; G8 - pH 7,5 ACP. Os grupos G2, G3, G6 e G7 foram tratados com o gel clareador por 8 h/dia durante 14 dias, enquanto as amostras dos grupos G4 e G8 foram submetidas ao agente clareador por 30 min/duas vezes ao dia, durante 14 dias. Os blocos de esmalte foram corados com solução de Rodamina B e a área fluorescente de desmineralização foi quantificada utilizando CLSM. Os dados foram submetidos a ANOVA e teste de Fisher (p<0,05). Para ES, os tratamentos clareadores aumentaram significativamente a área de desmineralização quando comparado com os grupos não clareados, entretanto, para LC não foi observado diferença estatística significante entre os grupos. A adição de ACP e Ca na composição dos géis clareadores não anulou os efeitos dos tratamentos clareadores no ES, assim como não teve capacidade de remineralizar o LC.

Efeito da ciclagem térmica na microinfiltração e microtração de restaurações de resina composta / Effect of thermal cycling on microleakage and µTBS of resin-composite restorations

O objetivo deste estudo foi avaliar a microinfiltração e a resistência de união à dentina por meio do teste de microtração em restaurações classe III, usando dois sistemas adesivos - o autocondicionante Clearfil SE Bond®/ Kuraray (SE) e o sistema de condicionamento ácido total Single Bond®/3MEspe (SB) -, submetidas (C) ou não à ciclagem térmica (NC). Foram preparadas duzentas cavidades classe III em incisivos bovinos, divididas em quatro grupos: G1:SB/NC; G2:SB/C; G3:SE/NC; G4:SE/C. Após restaurados, os G1 e G3 foram imersos em solução corante e os dentes, levados à cortadora metalográfica, sendo as restaurações seccionadas no sentido V-L em fatias de 0,7 a 0,8 mm. Essas secções foram, primeiramente, avaliadas quanto à penetração de corante e, em seguida, submetidas ao teste de microtração (área adesiva: 1 mm2), confeccionando-se espécimes em forma de "hourglass". Para os G2 e G4 as amostras foram submetidas a 2000 ciclos térmicos (5-55 ºC) e, após, sofreram os mesmos procedimentos descritos para os G1 e G3. Quanto à microinfilitração, os resultados foram analisados pelo teste de Kruskal-Wallis (p < 0,05), não demonstrando diferença estatisticamente significativa entre os grupos. Os dados de microtração (MPa) foram submetidos ao teste Anova dois fatores e Tukey (p < 0,05): G1:18,80a; G2:19,78a; G3:13,29c; G4:6,23b. Independentemente da ciclagem térmica, os dois adesivos apresentaram a mesma permissibilidade de microinfiltração. O desafio térmico influenciou negativamente na força de adesão do autocondicionante SE, mas não interferiu nos valores do SB.

The aim of this study was to evaluate the microleakageand μTBS of class III composite resin restoration using two bonding systems – the self etching primer Clearfil SE Bond/Kuraray (SE) and the one-bottle Single Bond/3MEspe (SB) subjected (C) or not (NC) to thermal cycles. 200 box-type class III cavities were prepared on surfaces of bovine incisors and divided into 4 groups: G1:SB/NC; G2:SB/C; G3:SE/NC; G4:SE/C. After the restorative procedures, G1 and G3 were immersed in a dye solution and the restorations were sectioned perpendicular to the cervical margin interface into 0.7± 0.2 mm thick slabs. These sections were first evaluated according to dye penetration and then the slabs were further trimmed at the interface to produce samples with a hourglass shape (cross-sectional surfacearea of 1mm2) to μTBS test evaluation. The samples ofG2 and G4 were thermocycled (2.000 cycles, 5-55 oC) and then subjected to the same procedures described for G1 and G3. The microleakage results were analyzed by the de Kruskal-Wallis (p < 0.05) test, and no differences were observed among groups. The μTBS means were analyzed by the Anova 2 way and Tukey test:G1:18.80a; G2:19.78a; G3:13.29c; G4:6.23b. Regardless the thermal cycles, both adhesive systems present the same microleakage results. However, for SE thermal cycling had adversely affected the bond strength values,but for SB no differences were observed.