ABSTRACT
Objective To analyze the etiology of fever of unknown origin (FUO).Methods A total of 372 patients with FUO who hospitalized in Capital Medical University Affiliated Beijing Friendship Hospital were retrospectively analyzed from January 2003 to August 2013.All the patients were divided into two groups:group A (January 2003-December 2007) and group B (January 2008-August 2013).Diagnosis rate,duration of hospitalization (days) and time to diagnosis between the two groups were artificially compared.Results Of the 372 FUO cases,336 were positively diagnosed with a diagnosis rate of 90.3％.Infectious diseases were still the primary causes of FUO (60.2％),including 72 cases (32.1％) of tuberculosis.Connective tissue diseases accounted for 12.9％ of the FUO cases,malignancies were 8.3％,and miscellaneous diseases were 8.9％.Yet thirty six patients (9.7％) could not be confirmed until they were discharged from hospital.The duration of fever in patients with malignancies was longer than that with infectious diseases [60.0 (30.0,90.0) days vs 30.0 (20.0,60.0) days,P =0.003].Time to diagnosis of connective tissue disease and malignancies was longer than infectious diseases [(12.0 (7.3,18.8) days and 11.0 (7.0,18.0) vs 5.0 (3.0,8.0) days,both P values =0.000].The duration of hospitalization in group A was longer than that of group B [17.0(12.0,30.0) days vs 14.0(10.0,20.0) days,P =0.000].The diagnosis rate and time to diagnosis of group A were similar with those of group B.The proportion of connective tissue diseases in group A was higher than group B(18.1％ vs 9.2％,x2 =6.201,P =0.013).The proportion of infectious disease,malignancies and miscellaneous diseases was not significantly different between the two groups.Conclusions Infectious diseases are the major causes of FUO,and the most common cause is tuberculosis.Connective tissue diseases and malignancies are the second and third causes of FUO.The duration of fever and time to diagnosis are significantly different between the different origins.
ABSTRACT
BACKGROUND: Radio frequency (RF) magnetron sputtering is a mature technique to prepare metallic (ceramic) coating on ceramic (metallic) substrate, which possesses low-amplitude temperature increasing substrate,rapid deposition rate, even coating component, stable performance, high binding intensity and other advantages.OBJECTIVE: To investigate the structure of hydroxyapatite(HA) coating prepared with RF magnetron sputtering technique and the binding performance of coating and interface of substrate.DESIGN: Single-sample observation.SETTING: College of Material Science and Engineering, Jiangsu University.MATERIALS: 30 mm×30 mm×3 mm Ti-6Al-4V plate and JGP500 MultiFunction Ultrahigh Vacuum Magnetron Sputtering System were used in this experiment.METHODS: This experiment was carried out at the Center of Material Experiment, Jiangsu University from December 2003 to September 2004.HA coating was prepared on the surface of Ti-6Al-4V substrate with RF magnetron sputtering technique, appearance of coating surface and crosssection were observed with scanning electron microscope (SEM), phase structure of coating was analyzed with X-ray diffractometer,Ca/P of coating was analyzed with Energy Dispersive X-ray Spectrometer and binding intensity of coating and interface of substrate was measured with e thoxyline resin-7 butt joint.MAIN OUTCOME MEASURES: ① Micro-appearance of HA coating.② Composition of HA coating and the effect of postprocessing. ③ Binding status and intensity of HA coating and substrate interface.RESULTS: ①Under the SEM, coating surface of HA was rough and uneven in surface, presented many pores and reticular structure. Pore area was about 30% to 40%. ② Ca/P of HA coating was 1.7. The essential component of treated HA coating was HA with high crystallization, without other calcium and phosphonium phase. ③ The binding intensity of HA coating and substrate interface was 51.2 MPa.CONCLUSION: HA coating prepared with RF magnetron sputtering technique has good appearance, high binding intensity at the interface of substrate.