Effect of type of carrier material on the in vitro properties of solid dispersions of progesterone / 药学学报

This study investigated the effect of different carrier materials on the in vitro properties of progesterone solid dispersions. The solid dispersions of the insoluble drug progesterone were prepared by hot melt extrusion technique using rheological properties as the index of investigation, and the in vitro properties of the solid dispersions were characterized. Scanning electron microscope revealed solid dispersions with rough surfaces and agglomerated microstructures into irregular lumpy particles. Differential scanning calorimetry and powder X-ray diffraction showed the change of progesterone crystalline form in solid dispersions from crystalline to amorphous state. In vitro dissolution studies showed that solid dispersions prepared with different carrier materials can effectively improve the dissolution rate of drugs. The results of the study showed that the type of carrier material had a significant effect on the in vitro properties of solid dispersions, providing a reference for the study of solid dispersions in the controlled release of insoluble drugs.

Influence of root canal sealer composition on postoperative pain after endodontic treatment of permanent teeth: a systematic review and meta-analyses / Influência da composição do cimento endodôntico na dor pós-operatória de dentes permanentes tratados endodonticamente: uma revisão sistemática e meta-análise

Postoperative pain is a frequent complication after root canal treatment. Its management is an important aspect of endodontic practice. Some treatment-related parameters were associated with the development of postoperative pain, including the sealer composition and extrusion. Objective: This systematic review aimed to answer the clinical question: Do root canal sealers composition influence postoperative pain after endodontic treatment of permanent teeth? Material and Methods: Electronic searches were conducted in PubMed, Scopus, Web of Science, Cochrane, LILACS, and grey literature databases until September 2021. The studies were qualitatively assessed using the RoB2 tool (Cochrane) and the certainty of evidence (GRADE). Sensitivity and pooled estimates were calculated using a random-effects model. Twelve articles were included. Results: The risk of bias was high in one study, low in nine, and two had some concerns. Qualitative analyses showed no influence of sealer extrusion on postoperative pain. Meta-analyses showed no significant difference in postoperative pain with moderate to very low levels of certainty between AH Plus and calcium silicate-based sealers, in a 95% confidence interval. Analysis between AH Plus, Zinc Oxide and Eugenol (ZOE), and calcium hydroxide (Ca(OH)2)-based sealers were not performed due to heterogeneity and lack of data. Conclusion: Literature showed contrasting results in postoperative pain between AH Plus and ZOE-based sealers, with low to moderate certainty of evidence. Regarding Ca(OH)2-based sealers, a single study with a low level of certainty concluded that AH Plus presented less postoperative pain than Apexit Plus. Therefore, further studies are needed to assess the influence of these sealers on postoperative pain. Evidence showed no difference in postoperative pain between AH Plus and calcium silicate-based sealers. Sealer extrusion is a variable that requires further studies (AU)

A dor pós-operatória é uma complicação frequente após o tratamento endodôntico. O seu manejo é um importante aspecto na prática endodôntica. Algumas variáveis relacionados ao tratamento foram associados com o desenvolvimento da dor pós-operatória, incluindo a composição e extrusão dos cimentos endodônticos. Objetivo: Esta revisão sistemática objetivou responder a seguinte pergunta clínica: A composição dos cimentos endodônticos podem influenciar a dor pós-operatória de dentes permanentes tratados endodonticamente?Material e Métodos: Buscas eletrônicas foram realizadas nas bases de dados no PubMed, Scopus, Web of Science, Cochrane, LILACS, e literatura cinzenta até setembro de 2021. Os estudos foram avaliados qualitativamente usando a ferramenta RoB2 (Cochrane) e a certeza de evidência (GRADE). A sensibilidade e as estimativas agrupadas foram calculadas usando um modelo de efeitos aleatórios. Doze artigos foram incluídos. Resultados: O risco de viés foi alto em um estudo, baixo em nove e dois tiveram algumas preocupações. A análise qualitativa mostrou que não há influência da extrusão do cimento na dor pós-operatória. A meta-análise mostrou que não houve diferença estatisticamente significante na dor pós-operatória entre o AH Plus e os cimentos a base de silicato de cálcio com moderada a muito baixa certeza de evdência. Análises entre os cimentos AH Plus, óxido de zinco e eugenol (OZE) e hidróxido de cálcio não foram realizados devido a heterogeneidade e falta de dados. Conclusão:A literatura sugere resultados contrastantes com relação a dor pós-operatória e entre os cimentos AH Plus e OZE, com baixa a moderada certeza de evidência. Já os cimentos a base de hidróxido de cálcio, um único estudo com baixa certeza de evidência concluiu que o AH Plus apresentou menos dor pós tratamento endodôntico do que o Apexit Plus. Portanto,mais estudos são necessários para avaliar a influência desses tipos de cimentos na dor pós-operatória. Com relação ao cimento AH Plus e os cimentos a base de silicato de cálcio não houve diferença estatística entre eles e a dor. A extrusão dos cimentos é uma variável que requer mais estudos (AU)

Manejo de extrusión forzada ortodóntica: Reporte de un caso / Management and Follow-up of Orthodontic Forced Extrusion: A Case Report

El presente caso clínico se enfoca en el diagnóstico y el tratamiento de erupción forzada en un paciente con trauma dental. Objetivo: Proponer una alternativa de tratamiento multidisciplinario el cual permita incrementar estructura dentaria a través de la extrusión forzada y posteriormente rehabilitarlo en función y estética. Métodos: Se describe el caso de un paciente adulto de 78 años de sexo masculino, sano y sin antecedentes patológicos, acude a la clínica de la Especialidad de Ortodoncia y Ortopedia Dentomaxilo facial, referido por un especialista en Endodoncia, debido a fractura corono-radicular de canino superior derecho, pilar de puente fijo de tres unidades En la exploración intraoral presenta fractura cervical de la corona del canino superior derecho. Como primer paso, se realizó tratamiento endodóntico en la pieza dentaria y colocación de un aditamento intraconducto de soporte (endoposte vaciado), con el objeto de mejorar la tracción ortodóntica. Este aditamento consistió en un poste colado con perforaciones. Se procede a colocar aparatología fija en la arcada superior con técnica MBT (slot 0.022), del molar derecho hasta el canino izquierdo de cementado indirecto y pasivo (con los slots de los brackets alineados). Inmediatamente después, se colocó un arco rectangular 0.019 x 0.025 de acero inoxidable con un doblez de extrusión a nivel del canino superior derecho. En el mismo doblez, se adaptó un loop tipo helix que funcionó como apoyo para colocar la ligadura pasiva (lace back). Resultados : El tratamiento realizado en este paciente es satisfactorio, coadyuvando en su estado de salud general mejorando su autoestima. Conclusión: Aquí se aprovecharon todas las ventajas que ofrece la extrusión ortodóntica forzada, incluso en un paciente adulto mayor, logrando una tracción de cuatro milímetros, que se consiguió gracias al empleo de fuerzas extrusivas ligeras y controladas sobre el órgano dentario afectado. Con la modalidad de tratamiento descrita se puede lograr un alargamiento de corona sin la necesidad de realizar una resección ósea, lo que permite una correcta rehabilitación protésica, devolviendo la función y estética al diente lesionado y brindando un beneficio integral al paciente.

The case of an adult patient with a complicated Crown fracture of the right upper canine due to trauma is reported, diagnosing a class VII Ellis coronal fracture. There are several treatment alternatives that range from the extraction, placement of a bone graft and placement of an implant, to a forced root extrusión with bone removal to allow the biological space and subsequently be restored. In the present case, a multidisciplinary orthodontic forced extrusion treatment is performed, which allows to increase the amount of clinical remnant, preserving the periodontal support and maintaining the biologic thickness, thus achieving to maintain the root remnant with good length so that prosthetic rehabilitation is facilitated. The clinical and radiographic follow-up was 12 months. The multidisciplinary treatment involved: Root canal treatment, forced extrusion with orthodontics, fibrotomy with root planing and fixed prosthesis.

Cantidad, estabilidad y digestibilidad de hidratos de carbono tras el proceso de extrusión: Impacto sobre el índice glicémico de harinas de consumo habitual en Chile

Las harinas de trigo, maíz, lentejas y arroz son elementales para la formulación de distintos alimentos de alto consumo en la población chilena. El proceso de extrusión es ampliamente utilizado por la industria alimentaria para generar propiedades que permitan la reconstitución instantánea de harinas. Sin embargo, dicho proceso tecnológico; afecta la cantidad, la estabilidad y la digestibilidad de los hidratos de carbono (CHO) del ingrediente alimentario. Estas propiedades nutricionales impactan directamente en la respuesta glicémica de los individuos y en el índice glicémico (IG) de los alimentos. La presente revisión analiza el efecto de la extrusión sobre las propiedades nutricionales de los CHO de alimentos elaborados a partir de harinas de consumo habitual en Chile. Factores como la temperatura, y en menor grado, la humedad y velocidad utilizadas en el proceso de extrusión, junto con el origen del grano utilizado, determinan las propiedades nutricionales de CHO presente en harinas extruidas. El estudio, control y estandarización de estas variables operacionales permitiría estandarizar la elaboración industrial de productos extruidos, impactando favorablemente; sobre la velocidad de hidrólisis de almidón y el IG de harinas de trigo, maíz, lentejas o arroz; y de alimentos formulados a partir de ellas.

Flours from wheat, corn, lentils, and rice are essential for the formulation of various high-consumption foods in the Chilean population. The extrusion process is widely used by the food industry to generate properties that allow for the instant reconstitution of flours. However, this technological process affects the nutritional properties of the carbohydrates (CHO) in the food ingredient, including quantity, stability, and digestibility; characteristics that directly impact the glycemic response of individuals and the glycemic index of foods. This review analyzes the effect of extrusion on the nutritional properties of CHO in foods made from commonly consumed flours in Chile. Factors such as temperature, and to a lesser extent, humidity, and speed used in the extrusion process, along with the origin of the grain used, determine the healthy properties of CHO in extruded flours. The utility of adjusting the mentioned variables in the extrusion process would allow for the standardization of industrial scaling in the production of extruded foods that would positively impact the starch hydrolysis rate and glycemic index of wheat, corn, lentil, or rice flours, and foods formulated from them.

Research progress of taste masking and evaluation technology of medicine / 中国药科大学学报

@#Most drugs taste bitter and irritating, resulting in poor compliance of patients, and the bad odor affects the therapeutic effect. The successful research and development of a drug should not only conform to the five quality characteristics of effectiveness, stability, safety, uniformity and economy, but also the compliance of patients to drugs with bad odor. The development of taste masking techniques is critical for bitter drugs.This review describes the principles, advantages and drawbacks of traditional taste masking techniques, and introduces the mechanism and application of novel taste masking techniques, such as melt granulation, hot melt extrusion, 3D printing, drug complex preparation, and bitter taste inhibitors. The in vitro evaluation methods of drug taste masking effect, such as functional magnetic resonance imaging, in vitro dissolution, and electronic tongue technology, are described. And introduce in vivo evaluation methods, such as animal and human taste, in the field of taste masking effect. A new strategy of BP neural network prediction model for drug taste evaluation is proposed, with a view to providing theoretical reference for the future research on drug taste masking.

Comprehensive orthodontic treatment of impacted teeth / 口腔疾病防治

@#Impacted teeth are a kind of complex malocclusion, and their incidence differs among different races, sexes and dental positions. The causes of impacted teeth include systemic factors and local factors, such as endocrine disorders, malnutrition, and acute and chronic infectious diseases. Local factors can cause abnormal tooth development or eruption during the process from tooth development to tooth eruption, such as damaged permanent tooth embryos caused by local inflammation or trauma, insufficient eruption space caused by premature loss of deciduous teeth, and eruption disorders caused by local lesions for example hyperplasia or odontoma. The clinical manifestation of impacted teeth is the absence of a permanent tooth in a normal position. We can use cone beam CT (CBCT) to locate the impacted teeth. Comprehensive orthodontic treatment includes surgical-assisted eruption, extraction of retained deciduous teeth or supernumerary teeth, removal of lesions such as odontomas and cysts, and expansion of the orthodontic space. When the dysfunctional local soft and hard tissues are removed during a surgical operation, the tooth still cannot sprout smoothly, and it needs to be assisted by orthodontic traction-guided eruption or extracted and autotransplantation. A clear diagnosis, evaluation of the difficulty of treatment and appropriate treatment are the keys to improving the success rate of treatment. In this paper, the epidemiology, etiology, diagnosis and corresponding treatment methods of impacted teeth will be reviewed, and the orthodontic treatment of impacted teeth will be comprehensively described to provide a reference for clinicians about the treatment of impacted teeth.

Dentoalveolar effects of skeletally anchored extrusion arch in anterior open bite patients: A prospective clinical trial

ABSTRACT Objective: The purpose of this prospective clinical trial was to explore the dental and soft tissue changes accompanying the use of skeletally anchored nickel-titanium (NiTi) extrusion arch in the correction of anterior open bite (AOB). Material and Methods: Twenty female patients with a mean age of 16.5 ± 1.5 years and a mean dentoalveolar AOB of 2.38±0.7 mm participated in this study. All patients were treated with an maxillary 0.017×0.025-in NiTi extrusion arch, with the aid of miniscrews inserted between the maxillary second premolars and first molars bilaterally, to act as indirect anchorage. Three-dimensional digital models and lateral cephalometric radiographs were taken just before the insertion of the extrusion arch (T0) and after 10 months (T1). Paired-sample t-tests were used in analyzing the data, to evaluate the changes after treatment (T1-T0). A significance level of p < 0.05 was used. Results: AOB was successfully closed in all patients, with a 4.35 ± 0.61 mm increase in the overbite. Maxillary incisors significantly extruded (2.52 ± 1.02 mm) and significantly reclined (5.78 ± 0.77°), with a resultant decrease in the overjet of 1.58 ± 0.5mm. A significant intrusion of maxillary first molars with no change in their inclination was observed. The upper lip showed a significant retraction tendency to the E-plane, and a significant increase in the nasolabial angle was observed. Conclusion: The skeletally anchored NiTi extrusion arch was an effective technique in treating AOB, with no adverse effects on the molars.

RESUMO Objetivo: O objetivo deste ensaio clínico prospectivo foi avaliar as alterações dentárias e em tecidos moles que acompanham o uso de arco de extrusão de níquel-titânio (NiTi) com ancoragem esquelético na correção da mordida aberta anterior (MAA). Material e Métodos: Participaram deste estudo 20 pacientes do sexo feminino com idade média de 16,5 ± 1,5 anos e MAA dentoalveolar (média de 2,38 ± 0,7 mm). Todos os pacientes foram tratados com arco de extrusão de NiTi 0,017×0,025" superior, com auxílio de mini-implantes inseridos entre os segundos pré-molares e primeiros molares superiores bilateralmente, para atuar como ancoragem indireta. Modelos digitais tridimensionais e radiografias cefalométricas laterais foram realizados imediatamente antes da inserção do arco de extrusão (T0) e após 10 meses (T1). Testes t para amostras pareadas foram utilizados na análise dos dados, para avaliar as alterações após o tratamento (T1-T0). Um nível de significância de p< 0,05 foi usado. Resultados: A MAA foi fechada com sucesso em todos os pacientes, com aumento de 4,35 ± 0,61 mm na sobremordida. Os incisivos superiores foram significativamente extruídos (2,52 ± 1,02 mm) e significativamente reclinados (5,78 ± 0,77°), com uma consequente diminuição na sobressaliência de 1,58 ± 0,5 mm. Foi observada intrusão significativa dos primeiros molares superiores, sem alteração na sua inclinação. O lábio superior apresentou tendência significativa de retração em relação ao plano E, e foi observado aumento significativo do ângulo nasolabial. Conclusão: O arco de extrusão de NiTi esquelético foi uma técnica eficaz no tratamento da MAA, sem efeitos adversos nos molares.

Preparation and properties of silica/hydroxyapatite whiskers porous ceramics scaffold / 中国修复重建外科杂志

OBJECTIVE@#To investigate the preparation and properties of the novel silica (SiO 2)/hydroxyapatite (HAP) whiskers porous ceramics scaffold.@*METHODS@#The HAP whiskers were modified by the SiO 2 microspheres using the Stöber method. Three types of SiO 2/HAP whiskers were fabricated under different factors (for the No.1 samples, the content of tetraethoxysilane, stirring time, calcination temperature, and soaking time were 10 mL, 12 hours, 560℃, and 0.5 hours, respectively; and in the No.2 samples, those were 15 mL, 24 hours, 650℃, and 2 hours, respectively; while those in the No.3 samples were 20 mL, 48 hours, 750℃, and 4 hours, respectively). The phase and morphology of the self-made HAP whisker and 3 types of SiO 2/HAP whiskers were detected by the X-ray diffraction analysis and scanning electron microscopy. Taken the self-made HAP whisker and 3 types of SiO 2/HAP whiskers as raw materials, various porous ceramic materials were prepared using the mechanical foaming method combined with extrusion molding method, and the low-temperature heat treatment. The pore structure of porous ceramics was observed by scanning electron microscopy. Its porosity and pore size distribution were measured. And further the axial compressive strength was measured, and the biodegradability was detected by simulated body fluid. Cell counting kit 8 method was used to conduct cytotoxicity experiments on the extract of porous ceramics.@*RESULTS@#The SiO 2 microspheres modified HAP whiskers and its porous ceramic materials were prepared successfully, respectively. In the SiO 2/HAP whiskers, the amorphous SiO 2 microspheres with a diameter of 200 nm, uniform distribution and good adhesion were attached to the surface of the whiskers, and the number of microspheres was controllable. The apparent porosity of the porous ceramic scaffold was about 78%, and its pore structure was composed of neatly arranged longitudinal through-holes and a large number of micro/nano through-holes. Compared with HAP whisker porous ceramic, the axial compressive strength of the SiO 2/HAP whisker porous ceramics could reach 1.0 MPa, which increased the strength by nearly 4 times. Among them, the axial compressive strength of the No.2 SiO 2/HAP whisker porous ceramic was the highest. The SiO 2 microspheres attached to the surface of the whiskers could provide sites for the deposition of apatite. With the content of SiO 2 microspheres increased, the deposition rate of apatite accelerated. The cytotoxicity level of the prepared porous ceramics ranged from 0 to 1, without cytotoxicity.@*CONCLUSION@#SiO 2/HAP whisker porous ceramics have good biological activity, high porosity, three-dimensional complex pore structure, good axial compressive strength, and no cytotoxicity, which make it a promising scaffold material for bone tissue engineering.

Preparation of 3D printed metoprolol tartrate chewable tablets and optimization of printing process / 药学学报

With the growing demand of personalized medicine for children, it is especially important to develop medicines for children. In this study, using metoprolol tartrate as model drug, we developed 3D printed chewable tablets suitable for children with automated dosage distribution using semi-solid extruded (SSE) 3D printing technology. Based on the quality by design concept, this study prepared a semi-solid material with good printability using gelatin as the substrate, constructed 3D models and printed tablets with the aid of computer-aided design. The printing parameters were optimized and determined as follows: print temperature of 35-37 ℃, print speed of 25 mm·s-1, fill rate of 15%, and number of outer profile layers of 2. Subsequently, the printing process and the quality uniformity of the tablets were verified, and a linear relationship between the dose and the number of model layers was obtained. Finally, 3D printed chewable tablets were superior in terms of appearance, dose accuracy and compliance compared with traditional split-dose commercially available tablets. In this study, 3D printed metoprolol tartrate chewable tablets with good performance were successfully prepared to address the personalized medication needs of pediatric patients.

Recent advances of pharmaceutical 3D printing extrusion molding technology / 药学学报

3D printing is an additive manufacturing technology with the help of digital control. Since FDA approved the first 3D printing drug in 2015, its research enthusiasm in the pharmaceutical field has been increasing year by year. In printing technology, fused deposition molding (FDM) and semi-solid extrusion (SSE) are the two most widely used extrusion molding technologies. In this review, recent advances of pharmaceutical 3D printing extrusion molding technology are reviewed from six aspects: mechanism, equipment, pharmaceutical excipients, applications, design and industrialization prospects of extrusion molding technology.

Orally Disintegrating Film: A Review of Its Formulation and Manufacturing Method

@#Oral route drug delivery system is still considered as the most convenient and patient friendly drug delivery route. Over the decades, many research has been performed to improve the functionality oral dosage form. Orally disintegrating film (ODF) is a newer oral drug delivery system, which is in the form of a thin film that will disintegrate in the oral cavity within a matter of seconds. The aim of this review paper is to recap ODF, its benefits, formulation contents and manufacturing method. With more research and development work has been conducted on ODF, the dosage form is expected to be manufactured and scaled up to be commercializable products to be sold in the market.

Engineering Parameters Responses during Extrusion Processing of Noodles Analogue from Water Yam, Yellow Maize, and African Yam Bean Flour Mixture

This study investigated the effect of extrusion process on engineering properties of noodles analogue from water yam, yellow maize, and African yam bean. Flour blend from water yam, yellow maize, and African yam bean were produced using the standard method of dry milling and was used to extrude noodles analogue using a brabender single screw laboratory extruder (Duisburg DCE 330 model) fitted with 3.0mmdie nozzle diameter. A central composite rotatable design (CCRD) with three variables, namely barrel temperature, feed moisture content and screw speed and five level coded – a, -1, 0, +1,, +a, was used for the study and data was generated at (p<0.05). Results of result of the engineering properties of noodles analogue showed that toque ranged from 22.4 to 60.50Nm/s, mass flow rate ranged from 33.90 to 109g/min-1, specific mechanical energy ranged from 100.19 to 385.97kj/kg, and the residence time ranged from 22 to 55s in this study. The CCRD was effective in explaining the effect of the process conditions on noodles analogue as influenced by barrel temperature, feed moisture content, and screw speed of the extruder. The data obtained from the study could be used for control of product characteristics.It was generally observed that the changing of feed moisture content, barrel temperature, and screw speed influenced an acceptable torque, mass flow rate, and residence time during the extruder operation. The noodles analogue produced at this cheap machine operating conditions could be projected for commercial production.

Functional Properties of Noodles Analogue from Water Yam, Yellow Maize, and African Yam Bean Mixtures – A Response Surface Methodology

Response surface methodology was used to investigate the effect of extrusion process on proximate composition of noodles analogue from water yam, yellow maize, and African yam bean flour mixture. Flour blend from water yam, yellow maize, and African yam bean were produced and was used to extrude noodles analogue using a Brabender single screw laboratory extruder (Duisburg DCE 330 model) fitted with 3.0 mm die nozzle diameter. A central composite rotatable design (CCRD) with three variables, namely barrel temperature, feed moisture content and screw speed and five level coded – a, -1, 0, +1, +a, was used and data analyzed by regression analysis. Results showed that bulk density ranged from 0.41 to 0.09 g/cm water solubility index ranged from 4.41 to 6.36%; water absorption capacity ranged from 2.05 to 5.66% and expansion ratio ranged from 1.62 to 3.81respectively. The coefficients of determinations (R2) were high and ranged from 0.9039 to 0.9887 at 5% level. The response surface plots suggested that the models developed had a good fit and the CCRD was effective in explaining the effect of the process conditions on noodles analogue as influenced by barrel temperature, feed moisture content, and screw speed of the extruder. The data obtained from the study could be used for control of product characteristics. The study indicated that improved noodles analogue from available and cheap roots, cereal and legumes such as water yam, yellow maize, and African yam bean can be produced for possible projection for the commercial production of noodles analogue.

The effect of rotation speed of XP-endo Shaper on apically extruded debris during endodontic procedures: an In Vitro study / El efecto de la velocidad de rotación de XP-endo Shaper sobre los desechos extruídos apicalmente durante los procedimientos de endodoncia: un estudio in vitro

Abstract The aim of this study was to evaluate the effect of using a higher rotation speed with the XP-endo Shaper (XPS) on apically extruded debris and operation time during endodontic treatment and retreatment procedures. Sixty mesial roots of mandibular first molar teeth were randomly assigned to four groups (Initial treatment groups: XPS used at 1000 or 3000rpm rotation speeds and Retreatment groups: XPS used at 1000 or 3000rpm rotation speeds). During the initial treatment and retreatment procedures preweighed eppendorf tubes were used to collect apically extruded debris, and the operation time was recorded in seconds. The extruded debris was quantified by subtracting the preinstrumentation from the postinstrumentation weight of the Eppendorf tubes. Data were analysed using two-way ANOVA at a significance level of 0.05. In all groups, the use of the XPS at 1000 or 3000rpm rotation speeds had no statistically significant effect on the amount of apically extruded debris (p>0.05). The use of the XPS at a 3000rpm rotation speed significantly decreased the instrumentation time (p<0.05). In summary, the use of the XPS at high rotation speeds in initial treatment and retreatment procedures did not have a significant effect on the amount of apically extruded debris but significantly decreased the operation time.

Resumen El objetivo de este estudio fue evaluar el efecto del uso de una mayor velocidad de rotación con XP-endo Shaper (XPS) sobre los desechos extruidos apicalmente y el tiempo de operación durante el tratamiento endodóntico y los procedimientos de retratamiento. Sesenta raíces mesiales de los primeros molares mandibulares se asignaron aleatoriamente a cuatro grupos (grupos de tratamiento inicial: XPS usado a velocidades de rotación de 1000 o 3000rpm y grupos de retratamiento: XPS usado a velocidades de rotación de 1000 o 3000rpm). Durante el tratamiento inicial y los procedimientos de retratamiento se utilizaron tubos Eppendorf pesados previamente para recoger los desechos extruidos apicalmente, y el tiempo de operación se registró en segundos. Los residuos extruidos se cuantificaron restando la preinstrumentación del peso postinstrumentación de los tubos Eppendorf. Los datos se analizaron mediante ANOVA bidireccional a un nivel de significación de 0,05. En todos los grupos, el uso del XPS a velocidades de rotación de 1000 o 3000rpm no tuvo un efecto estadísticamente significativo sobre la cantidad de detritos extruidos apicalmente (p>0.05). El uso del XPS a una velocidad de rotación de 3000rpm disminuyó significativamente el tiempo de instrumentación (p<0.05). En resumen, el uso del XPS a altas velocidades de rotación en los procedimientos de tratamiento inicial y retratamiento no tuvo un efecto significativo en la cantidad de detritos extruidos apicalmente, pero disminuyó significativamente el tiempo de operación.

Infección de cavidad anoftálmica por Scedosporium sp. en paciente inmunocompetente: Reporte de caso / Anophthalmic socket infection caused by Scedosporium sp. in immunocompetent patient: Case Report

Resumen Scedosporium sp. es un género de hongos filamentosos que de forma infrecuente se relaciona a infecciones localizadas o diseminadas en pacientes inmunocom prometidos, o inmunocompetentes con trauma penetrante contaminado. Reportamos el caso de un paciente masculino de 31 años con antecedente de trauma penetrante por arma de fuego requiriendo enucleación de su ojo izquierdo, quien 12 años posterior al trauma inicial presenta necrosis de la cavidad anoftálmica con extrusión del implante y lisis del párpado inferior, finalmente identificando Scedosporium sp. como germen causal, y un mucocele en el seno frontal como reservorio. El paciente recibió tratamiento médico con voriconazol sistémico, desbridamiento quirúrgico amplio, y resección endoscópica del quiste de retención mucoso, con una evolución satisfactoria. Las infecciones micóticas de la cavidad anoftálmica son infrecuentes, requiriendo una alta sospecha diagnóstica y trata miento agresivo para evitar consecuencias potencialmente devastadoras.

Abstract Scedosporium sp. is a genus of filamentous fungi that is infrequently related to localized or disseminated infections in either immunocompromised patients, or immunocompetent patients with penetrating contaminated trauma. We report the case of a 31-year-old patient with a history of penetrating gunshot wound that required enucleation of his left eye, who 12 years after initial trauma presents necrosis of the anophthalmic socket with implant extrusion and lysis of inferior eyelid, finally identifying the causal agent to be Scedosporium sp. The patient received medical treatment with systemic voriconazole, and wide surgical debridement, with a satisfactory evolution. Fungal infections of anophthalmic sockets are infrequent, requiring a high diagnostic suspicion and aggressive treatment to avoid potentially devastating consequences.

Management of compound odontoma with 70 denticles and impacted lateral incisor over an 8-year follow-up

Odontomas are benign developmental tumors formed by the improper growth of completely differentiated epithelial and mesenchymal cells of odontogenic origin. The etiology of odontoma is unknown and it is detected during routine radiographic examination. The ideal management is early detection and surgical enucleation. The commonly associated clinical problems of odontomas are delayed exfoliation of primary teeth, delayed eruption or impaction of permanent teeth, displacement of teeth, root resorption, congenital missing, and widening of follicular space. Here, we describe a unique case of compound odontoma with a high number of denticles managed based on a definite decision support system over 8 years. An 8-year-old boy with 70 denticles in the left maxillary region underwent enucleation. On periodic follow-up, the associated impacted lateral incisor was extruded orthodontically.

CAUDAL MIGRATION AND TRANS-ANAL EXTRUSION OF VENTRICULOPERITONEAL SHUNT IN A CHILD : A CASE REPORT

We present an unusual case of anal extrusion of the peritoneal end of a ventriculo-peritoneal shunt (VP shunt) in a 5 year old male child. The patient was suffering from aqueductal stenosis for which the shunt was placed 2 years ago. Pertinent literature is reviewed regarding this rare complication in such a common surgery.

Apical extrusion of debris with root canal instrumentation in primary teeth A systematic review

Aim: This study aimed to systematically review available literature of in vitro studies on apical extrusion of debris through rotary instrumentation in comparison to manual instrumentation in pediatric endodontics, and also to perform a comparison between various rotary instrumentation systems for assessment of debris extrusion. Materials and Methods: A comprehensive search was conducted on PubMed, Medline, Cochrane Library, Embase, Scopus, and Google Scholar without any language restriction and year of publication. A planned search strategy was made for PubMed and applied to other databases. After full-text reading, 7 articles were selected for quantitative synthesis. Modified CONSORT checklist of items for reporting in vitro studies of dental materials was used for quality assessment of included studies. Results: Root canal preparation with rotary instrumentation led to lesser apical debris extrusion than manual instrumentation. Self-adjusting file system was associated with the least debris extrusion among all included studies, followed by ProTaper Next, Kedo-S, ProTaper, K3, Mtwo, Revo-S, and Wave One. Conclusion: More apical debris extrusion was seen with manual instrumentation than rotary instrumentation. Furtrhermore, variance in debris extrusion was seen with different rotary file systems.

Compatibility and stability studies involving polymers used in fused deposition modeling 3D printing of medicines / 药物分析学报

One of the challenges in developing three-dimensional printed medicines is related to their stability due to the manufacturing conditions involving high temperatures.This work proposed a new pro-tocol for preformulation studies simulating thermal processing and aging of the printed medicines,tested regarding their morphology and thermal,crystallographic,and spectroscopic profiles.Gener-ally,despite the strong drug-polymer interactions observed,the chemical stability of the model drugs was preserved under such conditions.In fact,in the metoprolol and Soluplus? composition,the drug's solubilization in the polymer produced a delay in the drug decomposition,suggesting a pro-tective effect of the matrix.Paracetamol and polyvinyl alcohol mixture,in turn,showed unmistakable signs of thermal instability and chemical decomposition,in addition to physical changes.In the presented context,establishing protocols that simulate processing and storage conditions may be decisive for obtaining stable pharmaceutical dosage forms using three-dimensional printing technology.

Development and research of compound caffeine waterless swallowed granules based on reverse engineering / 药学学报

In this study, the reverse engineering technology was used to analyze the prescription and process of Doppelherz® Energy DIRECT, based on the composition of the prescription on the official website of the product, the detection method of composition is established according to the pharmacopoeia and literature information, combined with gravimetric analysis to complete prescription analysis. The prescription composition of the reference listed drug was determined to be composed of caffeine, taurine, vitamin B, anhydrous glucose, citric acid, sorbitol, sucralose, magnesium salts of fatty acids, in which the glucose content was 71.4%, the citric acid content was 7.0% and the magnesium salts of fatty acids content was < 5.8%. According to patent inquiry, Raman imaging and other technologies, the preparation process of the marketed preparation has been basically obtained, and the development of the self-made preparation has been completed on this basis. The study was approved by the Ethics Committee of the Academy of Military Medical Sciences. Combined with the results of the taste evaluation experiment and the caffeine dissolution test of the preparation in 1 min, the hot-melt extrusion technology was screened out as the taste-masking technology of the self-made preparation, the parameters of the hot-melt extrusion process were screened by differential scanning calorimetry analysis, and finally a product with good taste and qualified quality was obtained, which provided a reference method for the research and development of related preparations.