ABSTRACT
BACKGROUND:Lingual movable wing is a new type of lingual orthodontic technique and the different stretching lengths of the wring affect the torque control effect of anterior teeth.However,there is yet no related biomechanical research. OBJECTIVE:To investigate the displacement trend of dentition during adduction of mandibular anterior teeth and the effect of different wing stretching lengths on the biomechanical effect of mandibular anterior teeth. METHODS:The data of the mandible and lower dentition were collected by cone-beam CT and reconstructed using Mimics software to establish a three-dimensional finite element model of mandibular anterior teeth adducted by the lingual movable wing.The ANSYS software was used to analyze the initial displacement of the mandibular anterior teeth under the following conditions:A,2 mm stretching length;B,2.5 mm stretching length;C,3 mm stretching length;and D,3.5 mm stretching length. RESULTS AND CONCLUSION:The trend of initial displacement of lower dentition:The central incisors moved lingually with depression,the lateral incisors and canines moved mildly lingually with mesial lingual torsion,the second premolar was tilted distally with a marked lingual inclination and the first molar showed an overall mesial inclination with mesial crown eversion.Therefore,in the adduction cases of mandibular tooth extraction,attention should be paid to the lingual movement of the second premolar,which could be offset by corresponding techniques in clinic.The trend of anterior tooth displacement in all directions:from condition A to condition D,in the sagittal direction,the difference value in crown-root displacement of central incisors changed from-11.891 μm to-5.757 4 μm,indicating that the central incisor changes from oblique movement to overall movement.The difference value in crown-root displacement of lateral incisors changed from-11.828 1 μm to-6.711 45 μm,and that of canines changed from-7.572 3 μm to-4.695 5 μm,indicating that the oblique movement of the lateral incisors and canines is also changing to an overall movement.In the vertical direction,from condition A to condition D,the reduction of incisors was gradually increased,while that of canines was gradually decreased.These findings indicate that the stretching length of the wing can affect the oblique movement trend of the anterior teeth.As the wing continues to stretch,the torque control of the lower anterior teeth will become better.
ABSTRACT
BACKGROUND:In the treatment of edentulous maxillary implants supported fixed repair,the selection of upper scaffold structure materials and the design of different distal implant implantation methods have a close influence on the long-term stability of the whole mouth implant repair. OBJECTIVE:To comprehensively explore the influence of three different materials of upper scaffold and two implant fixation designs on the biomechanics of the fixed maxillary implant repair based on the three-dimensional finite element method. METHODS:Based on the conical beam CT data of a healthy adult with normal jaws,the Mimics software was used to separate the maxillary and maxillary dentin three-dimensional solid models,and the Geomagic Studio software was used to construct the three-dimensional finite element model of denture with denture implant and fixed maxillary arch combined with specific model parameters.According to the different designs of distal implants in the maxillary posterior region,two scheme models were established.Scheme 1(Design 1)was designed in accordance with the"All-on-4"design used in clinical practice.Two implants were vertically implanted in the bilateral incisor region of the maxilla,and the other two implants were implanted in the bilateral second premolar region at a 30° angle.In scheme 2(Design 2),two implants were vertically implanted in the lateral incisor region of the maxilla,and two short implants were vertically implanted in the posterior region of the maxilla in the bilateral second premolar region.Three materials(titanium,zirconia and polyether ether ketone)were used to assign values to the upper scaffold structure in the two designs,and six different models were obtained.The biomechanical effects of the implant,surrounding bone tissue and the upper scaffold structure were compared and analyzed in the oblique loading direction. RESULTS AND CONCLUSION:(1)The maximum stress peaks of all models were distributed in the neck region around the posterior implant and the cortical bone under the two edentulous implant fixed restoration schemes,regardless of the material of the upper scaffold.(2)Compared with the alternative design of Design 2,which adopted vertical implantation of short implants,Design 1 showed a more ideal stress distribution on the maxilla.(3)The scaffold model constructed by polyether ether ketone material transferred higher stress to the implant and surrounding bone tissue close to the loading zone of the upper jaw bone,followed by titanium and zirconia.As for the support itself,the peak stress of the upper scaffold of polyether ether ketone was significantly lower than that of the zirconia and titanium scaffolds.Zirconia scaffolds were used among the three upper scaffolds to disperse the stress distribution of implant and bone tissue.(4)The results suggest that both designs can be applied to clinical practice.However,from the perspective of biomechanics,the stress distribution of the implant,surrounding bone tissue and upper scaffold in Design 1 is more rational,which is more conducive to the long-term prognosis of fixed implant repair in patients with edentulous jaws.The upper scaffold material has a certain influence on the stress distribution of the implant-bone interface.
ABSTRACT
BACKGROUND:In implant restoration in the aesthetic area,zirconium dioxide is gradually becoming the most commonly used upper restorative material and has achieved better clinical results.Resin-ceramic composite,a new type of dental restorative material,begins to try to be used as an upper restorative material in implant restoration,but there is less research on the application of this material in implant restoration. OBJECTIVE:To compare the biomechanical differences between resin ceramic crowns and zirconia all-ceramic crown implant restorations in three occlusal relationships for restoring maxillary central incisors. METHODS:The cone-beam CT image data of a patient with single-crown implant restoration of maxillary central incisor were selected,and the maxillary bone model was extracted by using Mimics 21.0 software,and the model was imported into Solidworks 2020 software.The crown,adhesive,abutment,central screw,and implant were modeled,and the model of single-crown implant restoration of maxillary central incisor was assembled.After giving the model material property parameters(resin-ceramic composite and zirconia for the upper restoration materials)in ANSYS Workbench 2021 R1 software,three occlusal relationships(edge-to-edge occlusion,normal overjet and deep overbite)were simulated and loaded to analyze the stress distribution of the resin-ceramic crown and zirconia all-ceramic crown implant restoration models. RESULTS AND CONCLUSION:(1)The stress concentration areas in the implant restoration models of the resin-ceramic crown group and the zirconia all-ceramic crown group in different occlusal relationships were distributed in the upper restoration loading point,the abutment-implant connection,the implant neck and the surrounding bone tissue.As the occlusal relationship changed from the edge-to-edge to normal and deep overbite,the peak equivalent forces of the restorative abutment,central screw,implant,and bone tissue in both the resin-ceramic and zirconia all-ceramic crown groups gradually decreased.The highest peak equivalent forces were observed for the upper restorations in deep overbite.The zirconia all-ceramic crown group had the highest peak equivalent force in the adhesive layer in the edge-to-edge relationship,and the resin-ceramic crown group had the highest peak equivalent force in the adhesive layer in the deep overbite.(2)In the edge-to-edge occlusion,the peak equivalent force of the adhesive layer and central screw in the resin-ceramic crown group was slightly smaller than that in the zirconia all-ceramic crown group,and there was no significant difference between the two groups in the peak equivalent force at the upper restoration,restoration abutment,implant,and bone tissue.The peak stresses in the upper restoration,adhesive layer,and central screw of the resin-ceramic crown group were slightly less than those of the zirconia all-ceramic crown group at normal fit,and there were no significant differences between the two groups in the peak equivalent forces at the restoration abutment,implant,and bone tissue.In deep overbite,the peak adhesive,abutment,and central screw stresses were greater in the resin-ceramic crown group than in the zirconia all-ceramic crown group,with no significant differences in the upper restorations,implants,or bone tissue.(3)The results showed that the upper restorative material had no significant effect on the stress distribution of the implant and bone tissue,and had some effects on the stress distribution of the upper restoration,adhesive,restoration abutment,and central screw,but the difference was not significant.The occlusal relationship has a significant influence on the stress distribution in all structures and bone tissue of the implant restoration.The resin-ceramic crowns have a buffering effect on the stresses in the case of edge-to-edge and normal occlusion.
ABSTRACT
BACKGROUND:Among the pathogenic factors of cervical spondylosis,herniation of the intervertebral disc,dislocation of the facet joint and the stenosis of the intervertebral foramen are important factors leading to symptoms in patients.Moreover,inappropriate manipulation may aggravate the possibility of cervical disc rupture,leading to exacerbation of symptoms in patients. OBJECTIVE:To compare the effect between sagittal cervical manipulation and traditional cervical rotation manipulation on the area of the intervertebral disc,facet joint and intervertebral foramen at the operative segment by the finite element analysis. METHODS:The neck CT data of a male volunteer with a normal neck were selected and imported into Mimics 17.0 three-dimensional reconstruction software.Geo-magic Studio 12.0,Solidworks 2017 and Ansys Workbench 17.0 software were used for the construction of the finite element model of cervical vertebrae(C3-6)including intervertebral disc and articular cartilage.The lower end plate of the C5 vertebral body was fixed.A uniformly distributed vertical downward 50 N load was applied on the upper surface of the upper vertebral body(C3).The stress,deformation and deformation direction of the C4-5 intervertebral disc,joint capsule stress,the displacement of facet joints and the area of bilateral intervertebral foramen were compared between sagittal cervical manipulation and traditional rotation reduction. RESULTS AND CONCLUSION:(1)When using the rotation technique,the maximum normal equivalent stress(von Mises stress)of the C4-5 disc was 8.06 MPa;the total deformation was 1.05 mm,and the fiber ring expanded to the left and outside.When using the sagittal tip lifting technique,the maximum normal equivalent stress(von Mises stress)of the C4-5 disc was 2.60 MPa;the total deformation was 0.90 mm,and the fiber ring expanded to the left and back.Compared with the rotation technique,the pressure of the cervical manipulation technique on the disc was less(about 32.3%of the rotation technique),and the deformation degree of the disc was also light(about 85.7%of the rotation technique).(2)When the rotation technique was used,the maximum stresses of the left and right articular capsule ligaments were 0.37 MPa and 1.69 MPa,respectively.The overall displacement of the facet joint was 2.21 mm.The area of the right intervertebral foramen decreased by about 3.8%and the area of the left intervertebral foramen increased by about 0.9%.When the sagittal end lifting manipulation was performed,the maximum stresses of the left and right articular capsule ligaments were 0.27 MPa and 1.70 MPa,respectively;the overall displacement of the facet joint was 1.63 mm;the area of the right intervertebral foramen increased by about 2.6%,and the area of the left intervertebral foramen decreased by about 0.9%.Compared with rotation manipulation,sagittal end lifting manipulation had fewer changes in the displacement of facet joint,joint capsule stress and intervertebral foramen area,so it was safer to operate.(3)In conclusion,compared with cervical rotation manipulation,sagittal end lifting manipulation has fewer changes in facet joint displacement,intervertebral disc stress/deformation degree,joint capsule stress,and foraminal area.In clinical practice,more appropriate manipulation should be selected based on biomechanical results after an accurate assessment of patients'conditions.
ABSTRACT
BACKGROUND:The addition of traditional rod-rod fixation for atlantoaxial joint disease to C1-C2 pedicle screw-rod fixation(C1-C2 PSR)can provide stronger anti-rotation stability for screw/rod fixation,but there is a risk of installation difficulties,impact on bone graft bed,and spinal cord injury.The new horizontal screw-screw crosslink(hS-S CL)designed by the authors can effectively overcome the above shortcomings,but its biomechanical properties are unclear. OBJECTIVE:To analyze biomechanical properties of new horizontal screw-screw crosslink in C1-C2 PSR by three-dimensional finite element analysis. METHODS:CT thin layer scanning data were collected from the occipital base to the axis(C0-2)of one adult healthy male volunteer.The atlantoaxial finite element models were established respectively:the normal group,the unstable group,the non-crosslink group(unstable+C1-C2 PSR),and the crosslink group(C1-C2 PSR+hS-S CL).Range of motion and Von Miss Stresses in flexion and extension,lateral flexion and rotation of the four groups were calculated by applying 1.5 Nm torque to each finite element model,and the stress cloud was extracted. RESULTS AND CONCLUSION:(1)Range of motion of the unstable group was increased by 43.8%-78.7%compared with the normal group,and the range of motion of the internal fixation groups was 90.2%-98.7%lower than that of the unstable group under six conditions.The range of motion of the crosslink group and the non-crosslink group was basically the same in flexion and extension states,but in lateral flexion and rotation states,the range of motion of the crosslink group decreased 34.3%-43.8%and 78.6%-79.1%,respectively,compared with the non-crosslink group,and range of motion decreased most obviously in rotation state.(2)The stress peak of the internal plant model:The maximum stress of the crosslink group was generally smaller than that of the non-crosslink group,and the stress peak value of all the internal fixation groups was the lowest when the extension was carried out.(3)The stress cloud of internal plants showed that there was no obvious stress concentration phenomenon in the internal fixation,and the main stress distribution areas were the screw root and bone joint,and the crosslink ends were the screw tail groove or the joint rod joint.(4)The new horizontal screw-screw crosslink can obviously improve the anti-rotation stability of internal fixation and it can share part of the pressure in the three-dimensional motion direction of the internal fixation system and reduce the maximum stress of the internal plants.However,the stress distribution is obvious at both ends of the crosslink,and this part may be prone to fracture of the crosslink.
ABSTRACT
BACKGROUND:Lumbar fixed-point rotation operation needs collaborative operation of the doctor's hands,and outputs rotation and thumb thrust.Lumbar disc herniation can be treated through disc displacement and adjusting stress distribution.However,the mechanical effects of thumb thrust and the biomechanical effects of loading direction on manipulative effects remain unclear. OBJECTIVE:To compare the biomechanical difference of lumbar fixed-point rotation manipulation for treating lumbar disc herniation under different thrust directions. METHODS:The L3-5 normal three-dimensional finite element model was constructed and validity was verified.According to the intervertebral disc degeneration Pfirrmann grade,intervertebral disc degeneration was simulated by modifying the L4/5 intervertebral space height,the volume of the nucleus pulposus,as well as the material parameters of the annulus fibrosus,nucleus pulposus,and ligament.Finally,the pathological model of L4/5 moderate disc degeneration with left para-central herniation was constructed,and then the pathological models were used as research objects.Simulation technique:spinning to the right;taking the condition on changing the direction of the thumb thrust to establish three modes of operation(M1:thumb push to the left;M2:thumb push to the right;M3:no thrust push).The protrusion displacement and the disc stress,and the stress and strain of the facet joint cartilage were compared in the three operating modes. RESULTS AND CONCLUSION:(1)Maximum displacement value of L4/5 disc herniation:displacement was 2.672 3 mm for M1,1.156 1 mm for M2,1.826 4 mm for M3,M1＞M3＞M2.(2)The maximum Von Mises stress of L4/5 discs was 1.846 7 MPa for M1,0.419 0 MPa for M2,and 1.257 9 MPa for M3,M1＞M3＞M2.(3)L4/5 bilateral small cartilage produced different degrees of contact stress changes:It was 0.485 5 MPa for M1,0.026 7 MPa for M2,and 0.441 4 MPa for M3,M1＞M3＞M2.Right cartilage contact force was 0.000 5 MPa for M1,0.025 9 MPa for M2,and 0.001 3 MPa for M3,M2＞M3＞M1;the left greater than the right,M1 had the highest value;cartilage strain was consistent with contact stress changes.(4)Different operation modes will have some biomechanical influences on the diseased intervertebral disc and accessory structure.The M1 operation mode can maximize the displacement of protrusion,disc stress and left joint cartilage contact,which can better promote disc displacement,balance stress distribution and reduce facet joint disorder,so the operation is better.
ABSTRACT
BACKGROUND:There is an increasing demand for orthodontic treatment,and periodontally accelerated osteogenic orthodontics(PAOO)technique can make it possible to move orthodontic teeth that are limited by thin alveolar bone. OBJECTIVE:To investigate the biomechanics of orthodontic tooth movement before and after periodontally accelerated osteogenic orthodontics(PAOO)surgery to increase alveolar bone volume using the three-dimensional finite element method. METHODS:A patient undergoing PAOO surgery before orthodontic treatment to increase bone volume on the labial side of the mandibular anterior region was selected.The patient was under invisible orthodontics.Two three-dimensional finite element models were constructed based on the patient's preoperative and 6-month postoperative cone beam CT data.Both models simulated the movement of tooth 33:experiment Ⅰ:distal-central movement of 0.25 mm;experiment Ⅱ:lingual movement of 0.25 mm;and experiment Ⅲ:intrusion movement of 0.10 mm.The stress distribution and initial displacement trend of tooth 33,periodontal ligament and surrounding alveolar bone under the action of the invisible aligner were analyzed before and after the PAOO procedure. RESULTS AND CONCLUSION:Dental stress analysis:In the same orthodontic tooth movement,the maximum Von-Mises stress and overall stress values of tooth 33 were all higher before surgery than after surgery;there were similar distribution areas of maximum equivalent stress and overall distribution trends of Von-Mises stress before and after surgery.Periodontal ligament stress analysis:In the same orthodontic tooth movement,the maximum Von-Mises stress and overall stress values of the periodontal ligament were higher before surgery than after surgery,and there were similar distribution areas of the maximum equivalent stress and overall distribution trends of Von-Mises stress before and after surgery.Alveolar bone stress analysis:In the same orthodontic tooth movement,the maximum Von-Mises stress values of the alveolar bone around tooth 33 were higher before surgery than after surgery,while the equivalent stress distribution showed a gradual decrease from the top of the alveolar ridge to the root.Initial displacement analysis:In the same orthodontic tooth movement,the initial displacements in the main displacement direction for all six observation points of tooth 33 were smaller before surgery than after surgery,and showed a tendency to gradually decrease from the tooth tip to the apex.Therefore,there were differences in the biomechanical characteristics of orthodontic tooth movement before and after the PAOO surgery.With the clear aligner,the postoperative equivalent stress values on the dentition,periodontal ligament,and surrounding alveolar bone were lower than before the surgery,and the initial displacements of the orthodontic teeth after the surgery are larger than before.These findings suggest that PAOO can release the restriction of thin alveolar bone on the movement of orthodontic tooth by increasing alveolar bone thickness,effectively improving the force on the roots,periodontal ligament,and alveolar bone,avoiding the stress concentration on orthodontic tooth in the thin alveolar bone area that can cause complications when moving,and improving the efficiency of tooth movement.
ABSTRACT
BACKGROUND:Bone tissue remodeling is closely related to stress loading.Currently,there are few studies or guidelines on the relationship between bone and occlusal adjustment of implant prostheses and there is also a lack of scientific evidence. OBJECTIVE:To investigate the effects of different implant occlusal gaps on stress distribution,stress peak and displacement at the implant-bone interface under Ⅰ-Ⅳ bone conditions by a finite element method. METHODS:After scanning the equal-scale tooth model with an optical scanner,equal-scale models of the upper right first molar Straumann 4.8×8 mm BL RC implant and its related components was constructed using Solidworks 2022.Then,using Mimics,Geomagic,and Solidworks software,the maxillary and mandibular bone models of class Ⅰ-Ⅳ bones were established based on the bone classification proposed by ZARB and LEKHOLM in the literature,and the NORTON and TRISI bone density classification method.The models were assembled with the occlusal gaps of 0,20,40,60,80,and 100 μm for the restorations,and an additional set of homogeneous models without density ratio settings was constructed for comparison.After the above models were imported into Hypermesh for meshing,the material assignment,boundary constraints and parameter setting were performed for the finite element analysis.Finally,250 N was used as the loading force to simulate the maxillary and mandibular stress conditions.Stress distribution,peak stress and displacement of the implant-bone interface in each group of models were analyzed and compared. RESULTS AND CONCLUSION:Under the same loading conditions,the stresses in the implant restorations were evenly distributed with the occlusal contact points.When the occlusal gap reached 80 and 100 μm,stress interruptions occurred in the implant crowns under class Ⅰ bone and class Ⅱ,Ⅲ and Ⅳ bones,respectively.The displacement of the implant-bone interface was mainly concentrated in the cortical bone region around the implant and transmitted down the long axis of the implant to the cancellous bone region at the bottom.With the changes of class Ⅰ-Ⅳ jaw bones,the displacement and Von Mises stress in the cortical bone region increased in all groups,and were greater than those in the cancellous bone region.The Von Mises stress in the cancellous bone region was similar to that in the cortical bone region except that it showed a downward trend from class Ⅱ bone.However,when the occlusal gap increased,the stress and displacement peak values in the cortical bone and the cancellous bone showed a decreasing trend.The stress of the implant-bone interface was between 20 MPa and 60 MPa when the occlusal gap was 0-40 μm for class Ⅱ-Ⅳ bones and 60 μm for class Ⅳ bone,and the stress of the other groups was less than 20 MPa.The Von Mises stress was mainly concentrated in the neck of the implant,and the peak value of von Mises stress in class Ⅱ-Ⅳ bones with the occlusal gap of 20 μm was higher than that(144.10 MPa)in class Ⅰ bone with the occlusal gap of 0 μm.In the homogeneous model with different elastic moduli,the distribution of stress and displacement was more uniform than that in the heterogeneous model and the occlusal space should increase with the decrease of jaw bone density in clinical practice.To conclude,from the perspective of biomechanics,the alveolar bone should be taken into account in the occlusal adjustment of implant denture.An occlusal gap of 20-40 μm between a single dental implant and a natural tooth in the opposite jaw is a relatively suitable solution for occlusal adjustment under different bone conditions.However,due to the particularity of finite element analysis method,it needs to be further studied in combination with clinical practice.
ABSTRACT
BACKGROUND:The threaded conical implant has a good ability to control micro movements and is conducive to immediate loading.However,the effects of double-threaded conical cylindrical implants and conical cylindrical implants on stress distribution and initial stability of implant-bone interface after immediate loading have not been reported. OBJECTIVE:To investigate the impact of double-threaded conical cylindrical implants and conical cylindrical implants on the biological distribution of the implant and the surrounding bone interface during immediate loading in the mandibular molar region. METHODS:(1)Three-dimensional finite element analysis:Conical beam CT scans of the mandible and first molar of a volunteer were used to develop a basal model of the mandible.The double-threaded conical cylindrical implants and conical cylindrical implants were assembled with the mandibular models,and an immediate-load(or delayed implantation)implant model(a total of four models)for the first mandibular molar was established.Loads in four directions(100 N):axial,lingual and buccal 45°,mesial and distal,and buccal and lingual,were applied to the central fossa of each model's crown.Three-dimensional finite element method was used to analyze the implant displacement and the stress distribution at the implant-bone interface.(2)In vitro experiment:With the assistance of the oral implant robot,the double-threaded conical cylindrical implants and conical cylindrical implants were implanted on the same artificial bone pieces,separately,and the immediate load model of immediate implant implantation(or delayed implantation)was established in vitro(a total of four groups of models).Osstell resonance frequency analyzer and SmartPeg sensor were used to measure the implant stability coefficient in four vertical directions:front,rear,left,and right measurements,evaluate the initial stability,and verify the finite element analysis results. RESULTS AND CONCLUSION:(1)The displacement difference between double-threaded conical cylindrical implants and conical cylindrical implants was small when the immediate loading of delayed implantation was applied,but the maximum stress value of conical cylindrical implant-bone interface was greater than that of double-threaded conical cylindrical implant-bone interface.When the immediate loading of immediate implantation was applied,the maximum stress value and the maximum displacement of bone around the implant appeared when the load was applied in mesiodistal direction.The stress value of the conical cylindrical implant reached 298.84 MPa and the maximum displacement was 0.31 mm,both of which were larger than that of the double-threaded conical cylindrical implant.(2)The results of in vitro experiments showed that the stability coefficient of the double-threaded conical cylindrical implant was greater than that of the conical cylindrical implant.(3)Compared with the conical cylindrical implant,the double-threaded conical cylindrical implant has higher initial stability under immediate loading,suggesting that the use of double-threaded conical cylindrical implant should be given priority in clinical immediate loading.
ABSTRACT
OBJECTIVE@#To analyze the cement flow in the abutment margin-crown platform switching structure by using the three-dimensional finite element analysis, in order to prove that whether the abutment margin-crown platform switching structure can reduce the inflow depth of cement in the implantation adhesive retention.@*METHODS@#By using ANSYS 19.0 software, two models were created, including the one with regular margin and crown (Model one, the traditional group), and the other one with abutment margin-crown platform switching structure (Model two, the platform switching group). Both abutments of the two models were wrapped by gingiva, and the depth of the abutment margins was 1.5 mm submucosal. Two-way fluid structure coupling calculations were produced in two models by using ANSYS 19.0 software. In the two models, the same amount of cement were put between the inner side of the crowns and the abutments. The process of cementing the crown to the abutment was simulated when the crown was 0.6 mm above the abutment. The crown was falling at a constant speed in the whole process spending 0.1 s. Then we observed the cement flow outside the crowns at the time of 0.025 s, 0.05 s, 0.075 s, 0.1 s, and measured the depth of cement over the margins at the time of 0.1 s.@*RESULTS@#At the time of 0 s, 0.025 s, 0.05 s, the cements in the two models were all above the abutment margins. At the time of 0.075 s, in Model one, the gingiva was squeezed by the cement and became deformed, and then a gap was formed between the gingiva and the abutment into which the cement started to flow. In Model two, because of the narrow neck of the crown, the cement flowed out from the gingival as it was pressed by the upward counterforce from the gingival and the abutment margin. At the time of 0.1 s, in Model one, the cement continued to flow deep inside with the gravity force and pressure, and the depth of the cement over the margin was 1 mm. In Model two, the cement continued to flow out from the gingival at the time of 0.075 s, and the depth of the cement over the margin was 0 mm.@*CONCLUSION@#When the abutment was wrapped by the gingiva, the inflow depth of cement in the implantation adhesive retention can be reduced in the abutment margin-crown platform switching structure.
Subject(s)
Finite Element Analysis , Cementation/methods , Gingiva , Crowns , Dental Abutments , Dental Cements , Dental Stress AnalysisABSTRACT
Objective@#To analyze and investigate the effects of implant location and axial direction on the stress distribution of implants, abutments, central screws, and crowns during immediate loading of maxillary mesial incisors with different alveolar fossa morphology based on three-dimensional finite element method.@*Methods@#Referring to the oral CBCT images of a healthy adult, a three-dimensional finite element model was established for immediate implant loading of maxillary central incisors with three alveolar fossa morphs: labial, intermediate, and palatal; different implant sites(apical site, palatal/labial site) and axes(tooth long axis, alveolar bone long axis) were simulated; the established model was loaded with a force of 100 N. ANSYS software was applied to analyze the stress values of the implants, abutments, central screwss, and crownss. @*Results@#The 3D finite element models of 12 maxillary central incisors with different alveolar sockets were successfully established;the implants and their superstructures were least stressed when the maxillary central incisors with partial labial and partial palatal shape were placed along the long axis of the alveolar bone in the palatal/labial position for immediate implant loading;the implants and their superstructures were least stressed when the maxillary central incisors with central shape were placed along the long axis of the tooth in the palatal position for immediate implant loading. The implant and its superstructure were subjected to the least stress when the implant was placed along the long axis of the tooth in the immediate loading position. @*Conclusion@#The bio-mechanical characteristics of the implant and its superstructure are influenced by the different socket morphology, implantation sites and axes. Therefore, in clinical practice, different implantation axes and implantation sites should be developed for different socket morphs.
ABSTRACT
Objective To establish the three-dimensional finite element model of lumbar spine(L) 3-5 segments of the normal spine of 14-year-old adolescents to analyze the biomechanical changes of the lumbar spine after different degrees of lumbar foraminal plasty, and to provide reference for improvement of adolescent foraminoplasty. Methods A14-year-old female volunteer with no previous history of lumbar spine was selected to collect lumbar CT image data and we imported it into Mimics 16.0 software for modeling. ABAQUS software was used to conduct finite element model force analysis. Models M
ABSTRACT
@#Deep bite is a common clinical malocclusion that has a great impact on patients’ facial aesthetics and oral function. Bite opening is the key step in the treatment of deep bite, playing a decisive role in the development of mandible and the progress of orthodontic treatment. Torque and tip control during the correction of deep bites is a hot topic in orthodontics. The three-dimensional finite element method can accurately simulate clinical processes and conduct dynamic stress analysis, which provides the basis of the biomechanical mechanism. This paper reviewed the finite element analysis of various orthodontic systems for bite opening to provide a reference for clinical application. The emergence of mini-implants provided a new idea for anchorage control in bite opening. Finite element studies found that high-positioned mini-implants are beneficial for bodily tooth intrusion and proposed the ideal position for force application. For the finite element simulation of the reverse curve archwire, it was found that the intrusion and inclination of the anterior teeth increased with the curve depth of the archwire. The application of clear aligners has also been flourishing, but these forces are still difficult to effectively control. Finite element studies on their attachment design and corresponding tooth movement may be helpful to open the bite quickly and effectively. However, the existing studies still have modeling limitations. The structural simplification, linearization and nonstandard parameter definition of the model reduce model accuracy. Additionally, the existing research mostly focused on initial tooth movement, and studies on long-term tooth movement after bone remodeling are lacking. These studies are needed in the future.
ABSTRACT
【Objective】 To analyze the effect of different range and location of foramen formation on the biomechanics of lumbar spine by three-dimensional finite element analysis （D-FEA）. 【Methods】 A complete model of the lumbar spine （L5）， M0， was developed using the finite element method， and the models M1， M2， M3， M4 and M5 were obtained by sequentially simulating the apical， medial 1/4， 2/4， 3/4 and 4/4 graded resections of the left superior articular process of L5 under a lateral posterior approach with full spinal endoscopy. The displacements were recorded in six conditions： forward flexion， back extension， left and right lateral bending， and left and right lateral rotation. The results were compared between the resected models and the unresected group M0. 【Results】 The three-dimensional finite model of the L4-L5 segment developed in this experiment was valid. Compared with the unresected group M0， the differences in ROM were statistically significant for M1 under forward flexion load （all P<0.05）， M2 under forward flexion and back extension load （all P<0.05）， M3 and M4 under forward flexion， back extension and left and right lateral bending load （all P<0.05）. The differences were statistically significant for M3 and M4 under anterior flexion， posterior extension， left and right lateral flexion， and right rotation loads （all P<0.05）； and for M5 under anterior flexion， posterior extension， left and right lateral flexion and right rotation loads （all P<0.05）. Compared with M0 in the unresected group， the differences were statistically significant for M1 under anterior flexion loads （all P<0.05）， M2 under anterior flexion and left and right rotation loads （all P<0.05）. The differences were statistically significant for M3， M4 and M5 in forward flexion and extension， left and right lateral flexion， and left and right rotational loading （all P<0.05）. 【Conclusion】 In the process of foramen formation， removal of the tip or the medial quarter of the unilateral single segment of the upper articular process of the lumbar spine will affect the stability of the lumbar spine， and increase the maximum value of the stress of the intervertebral disc during the activities of the lumbar spine. Removal of one half or more will significantly damage the biomechanics of the lumbar spine. In order to avoid damaging the normal biomechanics of the lumbar spine， the upper articular process should be protected as much as possible during the whole spinal endoscopic foraminal reconstruction.
ABSTRACT
Objective @#To analyze the effect of different cavosurface angles on the stress distribution of ClassⅠ cavity composite resin filling of molars through the three-dimensional finite element method and to provide references for the preparation of ClassⅠ cavities.@*Methods@#Three-dimensional finite element models of ClassⅠ composite resin filling of mandibular first molars with three different cavosurface angles (group A: 90°, group B: 120°, group C: 135°) were established. Polymerization shrinkage of composites was simulated with a thermal expansion approach. The mechanical behavior of the restored models in terms of stress and displacement distributions under the combined effects of polymerization shrinkage and occlusal load (600 N) was analyzed.@*Results@# For ClassⅠ cavities with the same cavity size, the total stress of the restoration model and the maximum stress of the enamel in group A were less than those in groups B and C after cavity composite resin restoration with three cavity cavosurface angles (in which the width of the enamel bevel was 1 mm in groups B and C). The maximum stress of the dentin and adhesive was similar in the three groups, the maximum stress of the composite in group C was the largest, and the maximum stress of the composite in group B was the smallest. In terms of stress distribution, the maximum stress in each restoration model was mainly concentrated in the enamel at the cavosurface, near the enamel-dentin interface and at the edge of the restoration material.@*Conclusion@#From the point of reducing the stress of residual tooth tissue, the preparation of 90° angle without enamel bevel is an ideal method for cavity preparation when composite resin is used to fill ClassⅠ cavities of molars.
ABSTRACT
BACKGROUND: In recent years, the finite element analysis of lumbar biomechanics has become a hot topic. Lumbar lordosis is considered to reduce the pressure load on the lumbar intervertebral disc and protect the lumbar spine. OBJECTIVE: To study the biomechanical effects of lumbar traction on L1-L5 lumbar segments in normal physiological curvature, flexion position and maximum overextension position, and to evaluate the optimal physiological curvature of lumbar traction. METHODS: A healthy male volunteer, aged 26 years, with a height of 174 cm and a weight of 60 kg, was selected, who had no history of lumbar spine diseases. With the L3 segment as the traction site, a finite element model of the whole lumbar spine was established based on lateral radiographs of the lumbar spine at the initiation site and during the maximal overextension as photographed by a DR machine. Based on the three-dimensional finite element model of the lumbar spine, the stress values and distributions of the lumbar vertebrae, the intervertebral joints, the intervertebral discs and the anterior longitudinal ligaments of the whole lumbar spine under different physiological curvatures were calculated. The patient was fully informed of the study protocol and signed an informed consent. The study protocol was approved by the Ethics Committee of Rehabilitation Hospital Affiliated to Fujian University of Traditional Chinese Medicine. RESULTS AND CONCLUSION: (1) Under six kinds of simulated working conditions, the range of motion of L1-L2 was 9.31° for flexion and extension, 9.84° for right and left bending, and 4.43° for right and left rotation; the range of motion of L2-L3 was 10.22° for flexion and extension, 12.35° for left and right bending, and 4.57° for left and right rotation; the range of motion of L3-L4 was 11.20° for flexion and extension, 11.63° for left and right bending, and 5.32° for left and right rotation; the range of motion of L4-L5 was 13.16° for flexion and extension, 11.58° for left and right bending, and 5.05° for left and right rotation. Under the normal physiological curvature of the lumbar vertebrae, the stress value of different lumbar spine structures was much greater than the stress value of hyperextension traction. The normal curvature of the anterior longitudinal ligament was 2.47 MPa, and the curvature of hyperextension traction value was 21.20 MPa. The stress value of L3 was the highest, which was four times that of the hyperextension traction. The stress value of the intervertebral joints at L2-L3 and intervertebral disc was highest than that of any other segment of the lumbar spine. These findings indicate that the pressure of lumbar vertebrae, intervertebral joints and intervertebral discs in hyperextension position is less than that in normal physiological curvature traction, and the pressure of anterior longitudinal ligament is always within the safe range. Lumbar traction may have better clinical efficacy and definite security in hyperextension position.
ABSTRACT
BACKGROUND: In contrast to traditional drafting techniques, the superposition structure of the bed air column of spinal manipulation contributes to controlling the duration of traction. Finite element analysis is used to calculate the stress of adjacent lumbar segments with different traction durations. It provides a better theoretical basis for lumbar traction prescription in clinical spinal manipulative bed. OBJECTIVE: To analyze the stress and distribution of adjacent lumbar segments with different traction durations using the finite element analysis when the spine manipulation bed is used for traction. METHODS: A healthy male volunteer, aged 26 years, with a height of 174 cm and a weight of 60 kg, was selected, who was fully informed of the study protocol and signed an informed consent. The study protocol was approved by the Ethics Committee of Rehabilitation Hospital Affiliated to Fujian University of Traditional Chinese Medicine with an approval No. 2016XJS-001-01. According to the CT images of volunteers T12-S1, an effective three-dimensional finite element model of the lumbar spine was established. By means of three-dimensional finite element analysis, the stress changes of the lumbar vertebrae and facet joint adjacent to the L3 were calculated when the traction was maintained for 10, 20 and 30 seconds respectively. The internal law and mechanism of the changes were analyzed and discussed. RESULTS AND CONCLUSION: (1) When the pushing height was 5 cm and the action time was 1.25-17 seconds, the stress value of adjacent lumbar segments increased continuously. For the intervertebral disc, the stress value was 4.60-5.68 MPa for L2-L3, and 5.26-6.61 MPa for L3-L4; for the facet joint, the stress value was 7.01-8.67 MPa for L2-L3 and 5.22-6.50 MPa for L3-L4. (2) The stress of adjacent vertebral segments and facet joints remained basically unchanged after pushing for more than 24 seconds. Therefore, when the spine manipulation bed acts on the lumbar spine, it will not damage the adjacent lumbar segments, and the duration of action should be between 25 and 30 seconds.
ABSTRACT
BACKGROUND: Using interproximal enamel reduction, adding attachments and over-correction are major methods to improve the efficiency of correcting tooth torsion when using clear aligners in the clinic. However, the choice and placement of attachments depend on the experience and habits of orthodontists, and whether the effects are different has not been reported. OBJECTIVE: To explore the effects of rectangular attachment with different thicknesses and locations on the left maxillary canine tooth torsion in clear aligner by three-dimensional finite element analysis. METHODS: The finite element models of the clear aligner-attachment-maxillary canine-periodontal ligament-spongy bone-cortical bone and the clear aligner-maxillary canine-periodontal ligament-spongy bone-cortical bone were established according to the scanning data of in vitro maxillary canine. The models with attachments were divided into four groups based on different thicknesses of attachment, namely 0.5, 0.75,1.0, and 1.5 mm groups. The placement positions were divided into five areas: mesial, distal, occlusal, median, and gingival of canine. 2° clockwise rotation of the tooth axis (X axis) was applied to the clear aligner. The action of the appliance and the canine were calculated by MSC.Marc.Mentat software. Then, the nephograms of stress and displacement, and the maximum stress and displacement values were collected. RESULTS AND CONCLUSION: (1) Whether the rectangular attachment was used or not, the two models’ distribution of canine’s displacement and periodontal stress were the same. The stress values of periodontal ligament were all higher than those without rectangular attachment. (2) With the thickness of rectangular attachment increasing, the maximum displacement values of the canine increased gradually, which were 42.94, 49.32, 52.52 and 59.39 urn, respectively. (3) When the rectangular attachment was placed in different positions, the maximal displacement of canine teeth the attachment of which was placed on the median was almost the same with that of the gingival side. While the changes in the mesial and distal directions were irregular. (4) The use of rectangular attachments makes no effect on the movement of instant canines, which only plays a synergistic role in the control of canine tooth torsion. The thickness of the attachment has a certain effect on the torsion of appliance. When the thickness increases, the maximum displacement of the canine tooth and the stress of the periodontal ligament are increased. In the vertical direction, the closer of the placement is to the crown, the better the control of the rotated canine is.
ABSTRACT
BACKGROUND: In the treatment with dental implant prosthesis, the stress distribution of marginal bone and implant-bone interface Is affected by the factors of restoration and occlusion. The Internal structure and the stress distribution of Implant-bone Interface determine the long-term life of the implant and the stability of the marginal bone. OBJECTIVE: To analyze the effects of zirconia-based all-ceramic crown and Co-Cr alloy porcelain ceramic crown on the stress distribution of implant-bone interface, implant, prosthesis abutment, retention screw, and the inner structure in three occlusal relationships. METHODS: Using Mimics 17.0 software, the implant model of maxillary central incisor was established based on the cone beam CT of a patient undergoing prosthesis implantation Into the maxillary central incisor. Two kinds of three-dimensional finite element models of zirconia-based all-ceramic crown and Co-Cr alloy porcelain ceramic crown were constructed. The edge to edge occlusion, normal occlusion and deep overbite were simulated to analyze the stress distribution of Implant structure and the Implant-bone Interface in the three occlusal relationships. RESULTS AND CONCLUSION: (1) In the Co-Cr alloy porcelain ceramic crown group, when the occlusal relationship changed from the edge-to-edge occlusion to the normal occlusion and deep overbite relationships, the stress at the occlusal point of the prosthesis increased correspondingly, and the stress at the abutment, Implant and the Implant-bone Interface decreased. In the normal occlusal relationship, the stress at the retention screw was more concentrated than that in the other two occlusal relationships, and its peak value of the equivalent stress was higher. (2) In the zirconia-based all-ceramic crown group, when the occlusal relationship changed from edge-to-edge occlusion to the normal and deep overbite relationships, the stress peaks of the abutment, implant and implant-bone interface decreased gradually. In the normal occlusal relationship, the stress peaks of the occlusal point and the retention screw were higher than those in the other two occlusal relationships. (3) In the edge-to-edge occlusion relationship, the peak of equivalent stress at the occlusal point of the implant prosthesis in the Co-Cr alloy porcelain ceramic crown group was slightly higher than that in the zirconia-based all-ceramic crown group. The peaks of equivalent stress of the abutment, retention screw, Implant, and Implant-bone Interface in the Co-Cr alloy porcelain ceramic crown group were slightly lower than those in the zirconia-based all-ceramic crown group. In the normal occlusal relationship, the peak of equivalent stress at the neck of the implant in the Co-Cr alloy porcelain ceramic crown group was slightly higher than that in the zirconia-based all-ceramic crown group. In the deep overbite relationship, the peaks of the equivalent stress at the occlusal site of the implant prosthesis and the neck of the implant in the Co-Cr alloy porcelain ceramic crown group were higher than those in the zirconia-based all-ceramic crown group. The peaks of equivalent stress of the abutment, retention screw, and implant-bone interface In the Co-Cr alloy porcelain ceramic crown group were slightly lower than those in the zirconia-based all-ceramic crown group. (4) These results showed that different occlusal relationships and different upper structures of the implant prosthesis affected the stress distribution in each part of the implant and at the implant-bone interface. This finding may provide a reference for the prediction of long-term complications of implant prosthesis.
ABSTRACT
BACKGROUND: Flatfoot is a commonly seen disease in foot and ankle surgery, and stage II adult acquired flatfoot is mostly seen in clinic, so this stage is a key to treatment. However, medial column instability occurs in stage II adult acquired flatfoot, which is an important cause for arch collapse. Medial column stabilization can correct the deformity to great extent, but there is a lack of biomechanical study to assess the effect of medial column stabilization on the whole foot. OBJECTIVE: To investigate the biomechanical effects of medial column stabilization on stage II adult acquired flatfoot. METHODS: A three-dimensional finite element model of stage IIa and IIb adult acquired flatfoot was established. Geomagic software, Solidwork software and Abaqus software were used to simulate medial column stabilization operation (naviculocuniform joint fusion, tarsometatarsal joint fusion, and both fusion). The maximum pressure of plantar soft tissue, medial column bone and medial ligaments was compared before and after simulated single-foot weight loading. Meanwhile, the related parameters were measured to carry out a comprehensive comparison. RESULTS AND CONCLUSION: (1) The maximum plantar stress was located under the first metatarsal head after the simulated medial column stabilization operation. The maximum plantar stress increased significantly after the medial column stabilization in stage IIa flatfoot model, but did not change significantly after the medial column stabilization in stage IIb model. (2) After medial column fusion, the stress of the corresponding joint was reduced, but increased for the other joints of the first metatarsal column. (3) The stress of medial ligament and plantar fascia was not alleviated after medial column fusion. (4) These results indicate that simple medial column stabilization surgery cannot reduce the pressure of medial column of flatfoot in stage II acquired flatfoot adults. It can only be used as a combined surgery to stabilize joints with excessive motion and correct the deformity of supination of forefoot.