Functional impression technique using temporary denture for rehabilitation of severely atrophic maxillary and mandibular ridges / 대한치과보철학회지

Soft liner is used to functional impression technique when dental stone is immediately poured after taking impression because of viscoelasticity. In this case, a 78-year-old male visited for new dentures. Due to severe resorption of mandibular edentulous ridge, functional impression taking by closed mouth technique was planned. First of all, making maxillary and mandibular provisional dentures was done, and lined by soft liner to rehabilitate pressured maxillary and mandibular edentulous ridge. After this, Functional impression was taken by closed mouth technique using provisional dentures which are transformed to healed maxillary and mandibular edentulous ridge, and final denture were fabricated using maxillary provisional denture as a reference of artificial teeth arrangement. Consequently, restoring a complete edentulous patient with taking functional impression using provisional dentures resulted in recovering satisfying retention and function.

Complete denture made with closed-mouth impression technique on severely atrophied edentulous jaw / 대한치과보철학회지

At the department of prosthodontics, the elderly patients with severely atrophied alveolar ridge who have been wearing complete dentures for a long period frequently visit the clinic. In general, the open-mouth impression technique for manufacturing a mandibular complete denture to secure primary support on buccal shelf area has been prevalent. In addition, for securing retention and stability of mandibular denture, we should consider diagnosis, oral function, denture border, occlusal plane, teeth arrangement, and patient training, etc.. But in edentulous patients with severe alveolar bone atrophy, it may hardly secure retention and stability of mandibular complete denture. To promote these, some of clinicians are making an attempt manufacturing the mandibular complete dentures using closed-mouth impression technique based on several reports that compare various impression techniques including open-mouth and closed-mouth impression technique. This case report suggests closed-mouth impression technique may promote retention and stability of mandibular complete denture and compares between the two impression techniques clinically.

Preliminary study on the clinical application of temporary treatment denture in difficult edentulous cases before complete denture restoration / 华西口腔医学杂志

<p><b>OBJECTIVE</b>To explore the clinical effects of treatment denture on difficult edentulous cases before complete denture restoration.</p><p><b>METHODS</b>Thirty-six patients who experienced unsuccessful restoration of conventional complete dentures were included in this study. Treatment dentures were fabricated to solve issues such as abnormal occlusion, tissue surface problems, and neuromuscular dysfunction of the stomatognathic system caused by systemic diseases. The final complete dentures were fabricated by duplicating the treatment dentures. Jaw relation index, stability, and retention were evaluated at different stages. Oral health-related quality of life was measured using the Chinese version of Oral Health Impact Profile for edentulous subjects (OHIP-EDENT).</p><p><b>RESULTS</b>Among the 36 patients, 33 successfully completed the final restoration with positive effects.</p><p><b>CONCLUSIONS</b>Treatment denture is an effective pre-restorative option that can be used to correct abnormal occlusion, improve tissue surface problems, and aid in neuromuscular rehabilitation training. Treatment dentures contribute to the successful restoration of the final complete dentures and is worthy of clinical applications.</p>

An alternative impression technique based on McLean's functional impression concept / 대한치과보철학회지

In this case report, an alternative impression technique for fabricating removable partial dentures was used in a patient with very few remaining teeth. In this technique, an individual tray was made on the cast, which was made by relining interim denture and taking overimpression with irreversible hydrocolloid according to McLean's functional impression concept. This method showed the following advantages: the no need for border molding with modeling compound, time saving for denture impression without overextension and accurate seating of the individual tray.

Implant overdenture impressions using a dynamic impression concept

A dynamic impression is a functional impression that records the functional movement of the patient's own muscle and muscle attachment. This process reduces the number of random factors. This article describes a method for making a special tray using a dynamic impression concept that was made from provisional dentures used for implant healing. The individual tray is used to make a wash-impression to record the features of the mucosa in detail. The main advantage of this technique is that it provides a functional relationship of the implant components to the supporting tissues without overextension because provisional denture had been used for 2 months and the border length of individual tray was nearly the same as that of provisional denture. The delivery of the prosthesis constructed using this impression technique is time-saving because there is no need for border molding and there are fewer post-insertion appliance adjustments.

The effect of disinfectant agents on dimensional stability and surface roughness of a tissue conditioner material.

Purpose: The aim of this study was to determine the effect of disinfectant procedures on the dimensional stability and surface quality of a tissue conditioner used as a functional impression material. Materials and Methods: A tissue conditioner (Visco-gel) used as a functional impression material was disinfected by immersion in 5.25% sodium hypochlorite or 2% glutaraldehyde solutions for 10 or 20 minutes, respectively. The control group consisted of specimens (n=10) that were not treated by disinfectants. For testing the dimensional stability, impressions of an aluminum edentulous arch with three reference points were made. After 24 hours of storage in distilled water, the specimens were treated by one of the disinfection procedures. Impressions were poured and, subsequently, 50 stone casts were measured with a Nikon profile projector. For surface roughness evaluation, disks that contained Visco-gel were pressed against glass slides. The disks were then stored in distilled water for 24 hours. After disinfection, 50 disk-shaped dental stone casts were prepared. Surface roughness values were determined using a profilometer. For each test, data were subjected to two-way analysis of variance (ANOVA) followed by Tukey's test (α = 0.05). Results: The results of the dimensional stability test showed that immersion of Visco-gel impressions in 5.25% sodium hypochlorite solution or 2% glutaraldehyde solution did not significantly change the anteroposterior (AP) and cross-arch (CA) distances of the resultant stone casts when compared to the control group (P>0.05). The surface quality of dental stone casts formed by Visco-gel did not change significantly when impressions were immersed in the disinfectant solutions for either 10 or 20 minutes, or when stored in distilled water (P>0.05). Conclusion: The results showed that the disinfectant solutions used in this study did not have a significant effect on the surface quality and dimensional accuracy of Visco-gel as a functional impression material.

Changes of the surface roughness depending on immersion time and powder/liquid ratio of various tissue conditioners / 대한치과보철학회지

STATEMENT OF PROBLEM: Volume stability, microstructure reproducibility and fluidity along with compatibility with dental stone must be in consideration in order to use tissue conditioner as a material for functional impression. There are few studies concerning the influence of time factor in oral condition on surface roughness of the stone and optimal retention period in the oral cavity considering such changes in surface roughness. PURPOSE: The purpose of this study was to find out the influence of various kinds of tissue conditioner, its powder/liquid ratio and immersion time on surface roughness of the stone. MATERIAL AND METHODS: Materials used in this study were the three kinds of tissue conditioners (Coe-Comfort, Visco-Gel, Soft-Liner) and were grouped into three: group R - mixed with standard powder/liquid ratio that was recommended by the manufacturers, group M - mixed with 20% more powder, group L - mixed with 20% less powder. Specimens were made with the size of 20 mm diameter and 2 mm width. Each tissue conditioner specimens were subdivided into 5 groups according to the immersion time (0 hour, 1 day, 3 days, 5 days, 7 days), completely immersed into artificial saliva and were stored under 37degrees C. Specimens of which the given immersion time elapsed were taken out and were poured with improved stone, making the stone specimens. Surface roughness of the stone specimens was measured by a profilometer. RESULTS: Within the limitation of this study, the following results were drawn. 1. Major influencing factor on surface roughness of the stone model made from tissue conditioner was the retention period (contribution ratio (rho) = 62.86%, P < .05) of the tissue conditioner in oral cavity to make functional impression. 2. In case of Coe-Comfort, higher mean surface roughness value of the stone model with statistical significance was observed compared to that of Soft-Liner and Visco-Gel as immersion time changes (P < .05). 3. In case of group L (less), higher mean surface roughness value of the stone model with statistical significance was observed compared to that of R (recommended) and M (more) group as immersion time changes (P < .05). CONCLUSION: We may conclude that as the retention period of time in oral cavity influences surface roughness of the stone model the most and as the kind of tissue conditioner and its P/L ratio may influence also, clinician should well understand the optimal retention period in oral cavity and choose the right tissue conditioner for the functional impression, thus making the functional impression with tissue conditioner usefully.

A study on the visco-elastic properties of four currently used tissue conditioners / 대한치과보철학회지

The dimensional stability of tissue conditioners characterizes the ability of the materials to yield accurate functional impressions of oral mucosa. This study evaluated the viscoelastic property and the linear dimensional changes with the factor of time and thickness of tissue conditioners (COE-COMFORT(TM), Visco-gel, COE-SOFT(TM), Soft-Liner) The thickness of these materials were changed (1.5mm, 3.0mm) and the percentage changes in dimension were measured at 1h, 12h, 24h, 36h, 3day, 7day after specimen preparation. From the results large differences appear between the various tissue conditioners. The results suggest that the period recommended for forming functional impression would be 2-3days after insertion in the mouth. in addition, it is important to select tissue conditioners suitable for functional impression because of the wide range of dimensional stability among the materials.