ABSTRACT
Two methods including gas chromatography tandem mass spectrometry (GC-MS/MS) and high-performance liquid chromatography tandem mass spectrometry (LC-MS/MS) were established to detect common alkyl sulfonates and aryl sulfonates genotoxic impurities. Four alkyl sulfonates and methyl benzenesulfonate were determined by GC-MS/MS using butyl methanesulfonate as the internal standard, the chromatographic column was HP-5MS UI (30 mm × 0.25 mm, 0.25 µm), the carrier gas was helium, the flow rate was 1.0 mL·min-1 in a constant flow mode, the sample inlet temperature was set to 250 ℃, the split ratio was 10∶1, and the initial temperature of the heating program was 80 ℃, maintained for 1 minute, and then increased to 240 ℃ at a heating rate of 30 ℃·min-1 for 2 minutes. The mass spectrometry detector was an electron bombardment ion source (EI source), the data collection condition was multi reaction monitoring mode (MRM), and method validation using the raw material of clinical drug citalopram hydrobromide as a sample. The results showed that the linear range of four alkyl sulfonates and methyl benzenesulfonate were good at 3-50 ng·mL-1 and 9-150 ng·mL-1, with a correlation coefficient of r > 0.999, The spiked recovery was 80%-120%. The detection limits were 1 and 3 ng·mL-1; Ten aryl sulfonates determined by LC-MS/MS, the chromatographic column was CSH Fluoro phenyl (100 mm × 2.1 mm, 1.7 µm), the mobile phase was methanol (B)-5 mmol·L-1 ammonium formate (D), with a flow rate of 0.2 mL·min-1, and gradient elution was performed. The gradient program (T/% B) was set as 0/20, 25/90, 35/90, 42/20. The mass spectrometer detector was electro spray ionization with positive ionization mode (ESI+), the data collection was in dynamic multi reaction monitoring mode (dMRM), and the method was validated using the raw material of the clinical drug citalopram hydrobromide as a sample. The results showed that the linear range of aryl sulfonates were good at 9-2 000 ng·mL-1, 3-100 ng·mL-1 and 0.9-30 ng·mL-1, respectively. The correlation coefficient r > 0.999, the spiked recovery was 80%-120%. The detection limits were 30, 1 and 0.3 ng·mL-1. Two detection methods did not detect potential sulfonate genotoxicity impurities in the above APIs. The established analytical methods are reliable and effective, which can provide reference for drug quality control and detection.
ABSTRACT
Given that impurities may affect the quality and safety of drug products,impurity identification and profiling is an integral part of drug quality control and is particularly important for newly developed medications such as solriamfetol,which is used to treat excessive daytime sleepiness.Although the high-performance liquid chromatography analysis of commercial solriamfetol has revealed the presence of several impurities,their synthesis,structure elucidation,and chromatographic determination have not been reported yet.To bridge this gap,we herein identified,synthesized,and isolated eight process-related solriamfetol impurities,characterized them using spectroscopic and chromatographic tech-niques,and proposed plausible mechanisms of their formation.Moreover,we developed and validated a prompt impurity analysis method based on ultrahigh-performance liquid chromatography with UV detection,revealing that its selectivity,linearity,accuracy,precision,and quantitation limit meet the acceptance criteria of method validation stipulated by the International Council for Harmonization of Technical Requirements for Pharmaceuticals for Human Use.Thus,the developed method was concluded to be suitable for the routine analysis of solriamfetol substances.
ABSTRACT
@#Using high performance liquid chromatography and high resolution orbital trap mass spectrometry, a two-dimensional online desalting detection method was established to determine the structure of the impurities detected under the official testing conditions of lansoprazole enteric solution preparation, and a chromatographic method compatible with mass spectrometry was established to determine and presume the structure of the impurities that could not be separated by the the official testing method.The identification of impurity was to presume its structure according to the presence of impurity reference product, so as to investigate the difference of impurity spectrum of products from different manufacturers.The one-dimensional chromatographic conditions for the 2D online desalting method were the same as those in China Pharmacopoeia (2020) under relevant substances.Two-dimensional chromatography was performed on a Waters C18 T3 column (2.1 mm × 100 mm, 1.7 μm) with 0.1% formic acid in water-acetonitrile mobile phase and gradient elution.The chromatographic conditions for the compatible mass spectra were based on an Agilent Extend C18 (4.6 mm × 150 mm, 5 μm) column with mobile phase A: 25 mmol/L ammonium acetate and B: 25 mmol/L ammonium acetate-acetonitrile (1∶4) [pH adjusted to 6.5 with glacial acetic acid], with gradient elution. Nine impurities were detected by two-dimensional online desalting method, with 5 known impurities (A-E) and 4 unknown ones.14 impurities were detected by the compatible mass spectrometry method, with 9 unknown impurities (4 consistent with the results of two-dimensional online desalting method, and 5 newly detected).The structures and sources of the unknown impurities were deduced.The two detection methods of lansoprazole preparation by high-performance liquid chromatography-high resolution orbital trap mass spectrometry have guiding significance for quality control and process evaluation.
ABSTRACT
Aim To explore the alternative study on rat blood pressure method and HPLC method for vasopressin impurity test of oxytocin injection from biological extraction. Methods The HPLC method for the vasopressin impurity test in vitro was established and validated. The bio-extrac tion oxytocin injection samples and simulated samples were examined for vasopressin impurity by HPLC and rat blood pressure methods respectively. Results Vasopressin and adjacent impurity peaks were successfully separated by the established method. In the range of 210~13 330 IU•L -1the concentration of vasopressin had a good linear relationship with its peak area with r=0.999 9. The results of HPLC method were consistent with the biological examination method-rat blood pressure method in the current standard. Conclusions The method is proved to be specific, sensitive, and accurate, which can be used as a test method for vasopressin impurity to replace the rat blood pressure method in the current standard.
ABSTRACT
Capillary electrophoresis(CE)is widely used for the impurity profiling of drugs that contain stereo-chemical centers in their structures,analysis of biomolecules,and characterization of bio-pharmaceuticals.Currently,CE is the method of choice for the analysis of foodstuffs and the determination of adulterants.This article discusses the general theory and instrumentation of CE as well as the classification of various CE techniques.It also presents an overview of research on the applications of different CE techniques in the impurity profiling of drugs in the past decade.The review briefly presents a comparison between CE and liquid chromatography methods and highlights the strengths of CE using drug compounds as examples.This review will help scientists,fellow researchers,and students to understand the applications of CE techniques in the impurity profiling of drugs.
ABSTRACT
@#In this paper, the uncertainties of correction factors of fluconazole impurities determined by HPLC standard curve method were evaluated, and the main common factors affecting the accuracy of standard curve method were found, so as to improve the accuracy of the method.In this study, the corresponding fitting lines of fluconazole and its impurities A, B, C, D, F and I were established respectively, and the ratio of the slope of fitting lines of each impurity and its corresponding principal component was calculated as the correction factor of the impurity.Then on the basis of GUM method, the uncertainty of each impurity correction factor determined by standard curve method was evaluated according to the established uncertainty evaluation scheme of correction factor determination process.The correction factor and uncertainty of fluconazole impurities A, B, C, D, F and I were 1.068 ± 0.046, 0.102 ± 0.005, 0.0582 ± 0.0031, 1.382 ± 0.121, 0.802 ± 0.067 and 1.383 ± 0.119, respectively, and the coverage factor k was 2.Finally, the contribution rate of each uncertainty component was calculated.In the relative combined standard uncertainties urel(f) of fluconazole impurities A, B, C, D, F and I correction factors, the sum of contribution rate of slope uncertainty urel(K) of the linear equation of principal component and its impurity is more than 85%; in the slope uncertainties urel(K) of linear equation, the contribution rates of uncertainties of solution concentration in 8 of 12 data groups are more than 80%, and the contribution rates of uncertainties introduced by reference substance content in solution concentration are about 80%.It can be seen that the preparation of linear solution concentration is the most influential factor in the determination of impurity correction factor by standard curve method, followed by the linear fitting process.In the preparation process of linear solution concentration, the purity of reference substance is the most influential factor, followed by weighing and pipetting times.The conclusion can help the experimenters to better formulate experimental plans and ensure the accuracy of the results when doing similar work.
ABSTRACT
@#In this paper, chemical derivatization-high performance liquid chromatography was used to determine the potential genotoxic impurities chloroacetyl chloride and chloroacetic acid, respectively, in the raw material of azintamide.Derivatization was carried out using 2-nitrophenylhydrazine followed by the determination.Separation was performed on a Thermo Syncronis C18 column (250 mm × 4.6 mm, 5 μm), with mobile phase consisting of 0.1% phosphoric acid in water (A) and acetonitrile(B) by gradient elution, at a flow rate of 1 mL/min.The column temperature was 40 °C and the detection wavelength was 226 nm.The blank solvent, derivatization reagent, and azintamide did not interfere with the peak of the test substance, and the target component was well separated from the others.For impurities chloroacetyl chloride and chloroacetic acid, the limits of detection (LOD) were 7.5 ng/mL and 15 ng/mL respectively. There was a good linear relationship between the integral area and the concentration in the range of 30-300 ng/mL.The sample recovery rate was in the range of 87.37% ~ 109.75%.The two methods established in this study have good specificity, good precision, high sensitivity and simple operation, which can be used for the trace determination of potential genotoxic impurities chloroacetyl chloride and chloroacetic acid in the raw material of azintamide.
ABSTRACT
@#For the quality control of cetomacrogol 1000, a gas chromatographic method for the determination of residual impurities in cetomacrogol 1000, such as ethylene oxide, 1, 4-dioxane, ethylene glycol, diethylene glycol and triethylene glycol, was established and validated.The DB-1 column with headspace injection was used to detect ethylene oxide and 1, 4-dioxane with the inlet temperature of 150 °C, the FID temperature of 250 °C, the headspace equilibration temperature of 70 °C and the equilibration time of 45 min.The VF-17MS column with liquid injection was used to detect ethylene glycol, diethylene glycol and triethylene glycol with the inlet temperature of 270 °C, and the FID temperature of 290 °C.The results showed that ethylene oxide and 1,4-dioxane have a good linearity within their specified addition amount ranges (r > 0.999), with the RSD of precision of below 8.0% and the average recovery rates of 90.6% and 101.2%; and that ethylene glycol, diethylene glycol and triethylene glycol also have a good linearity between 3 ? 60 μg/mL (r > 0.999), with the RSD of precision of below 3.0%, and the recovery rates of 96% ~ 103%.The method established in this study has good specificity, linearity, precision and recovery rate, which can effectively detect the multi-component and trace impurities.
ABSTRACT
@#Gas chromatography-mass spectrometry (GC-MS) method was established for trace analysis of the potential genotoxic impurity chlorocyclohexane in trihexyphenidyl hydrochloride bulk drug, utilizing an RXI-5SIL MS column at isothermal temperature of 60 °C for the entire 6-minute run time.The inlet temperature was 180 °C and a split ratio of 10∶1 was used with the injection volume of 1.0 μL.The selective ion monitoring mode was set at m/z 82 for chlorocyclohexane with a detector voltage of 0.3 kV and an ion source temperature of 240 °C.The method was verified with respect to specificity, limit of detection (LOD), limit of quantitation (LOQ), accuracy, precision and robustness.Good linear correlation was achieved with coefficient r of 0.999 9 in the concentration range of 59.72-493 ng/mL.The intra- and inter-day precision was satisfactory (RSD ≤ 5.0%) and robust (RSD ≤ 1.65%).The proposed method in this study can be adequately adopted as a tool for quality assurance of trihexyphenidyl hydrochloride in routine test of potential genotoxic impurity.
ABSTRACT
@#A UPLC-MS/MS method was established for the determination of the genotoxic impurity (R)-5-(azidomethyl)-3-[3-fluoro-4-(4-morpholinyl)phenyl]-2-oxazolidinone in linezolid API and its glucose injection. Chromatographic separation was performed on a Waters Acquity UPLC HSS T3 column (100 mm × 2.1 mm, 1.8 μm) with 0.1% formic acid water-0.1% formic acid acetonitrile (60∶40) at a flow rate of 0.3 mL/min. The UPLC-MS/MS was equipped with electrospray ionization in positive ionization mode and multiple reaction monitoring mode. The results showed that the calibration curve was linear in the range of 4-12 ng/mL and the limit of quantification was 0.073 ng/mL.The average recoveries of the low, medium and high concentration (80%,100%,120% limit concentration) loading solutions were 101.14%, 100.59% and 101.47%, respectively (RSDs:0.73%, 1.10% and 0.91%, respectively).The sample solution was stable for 6 d.No genotoxic impurity of (R)-5-(Azidomethyl)-3-[3-fluoro-4-(4-morpholinyl)phenyl]-2-oxazolidinonewas not detected in the samples of linezolid API and its glucose injection.
ABSTRACT
An UPLC-MS/MS method was established for the quantification of the genotoxic impurities bis(2-chloroethyl)amine hydrochloride and 1-(3-chloropropyl)-4-(3-chlorophenyl)piperazine hydrochloride in trazodone hydrochloride. The chromatographic separation of the two genotoxic impurities was performed on Waters ACQUITY UPLC BEH C18 column (100 mm×2.1 mm, 1.7 μm) at 20 ℃. A mixture of 5 mmol·L-1 ammonium hydrogen carbonate aqueous solution and acetonitrile at a flow rate of 0.3 mL·min-1 in gradient elution mode was employed as mobile phase. The UPLC-MS/MS was equipped with electrospray ionization in positive ionization mode and adopted multiple reaction monitoring mode. We found that the calibration curves of the two genotoxic impurities were linear in the range of 0.1-10 ng·mL-1. The limit of detection was 0.10 ng·mL-1 for bis(2-chloroethyl)amine hydrochloride and the average recovery was 101.53% (RSD = 4.06%). The limit of detection was 0.01 ng·mL-1 for 1-(3-chloropropyl)-4-(3-chlorophenyl)piperazine hydrochloride and the average recovery was 97.95% (RSD = 1.27%). The sample solution was stable for 24 h. No bis(2-chloroethyl)amine hydrochloride was detected in the samples, and the content of 1-(3-chloropropyl)-4-(3-chlorophenyl)piperazine hydrochloride in the samples was within the limit. This research provides a method to improve the quality control standards of trazadone.
ABSTRACT
OBJECTIVE：To establish a method for the content determination of potential genotoxic impurity maleic hydrazide in azintamide raw material. METHODS ：HPLC-FLD method was adopted. The determination was performed on Thermo Syncronis C18 column with mobile phase consisted of 0.2 mol/L acetic acid-methanol （gradient elution ）. The column temperature was set at 30 ℃，the excitation wavelength was 315 nm and emission wavelength was 389 nm. The flow rate was 1 mL/min，and the sample size was 20 μL. RESULTS：The blank solvent and azintamide did not interfere with the determination of maleic hydrazide. The linear range of maleic hydrazide was 19.5-300 ng/mL（r＝0.999 9）. The limit of detection was 4.5 ng/mL and the limit of quantification was 19.5 ng/mL. The recovery ranged from 98.79％ to 103.76％（RSDs were lower than 3.00％，n＝9）. RSDs of precision and stability （24 h）tests were no more than 5.63％，and those of durability tests were less than 2.00％（n＝6）. Maleic hydrazide was not detected in 3 batches of azinamide raw material. CONCLUSIONS ：The method is specific ，sensitive and accurate. It can be used for the trace determination of maleic hydrazide in azintamide or other matrix.
ABSTRACT
The compatibility of kanamycin with sodium citrate for the formulation of kanamycin sulfate injection was determined, including optimization of the amount of sodium citrate in the injection and the sterilization process. An HPLC coupled with an evaporative light scattering detector (ELSD) was used to measure the amount of sodium citrate and the impurity profiles. A validated post-column derivatization HPLC coupled with a fluorescence detector (FLD) was used to determine the correlation between specific impurities in a domestic factory and sodium citrate, and then the formulation was evaluated by HPLC coupled with mass detector (MS) characterization of degradation products. The results show that the amount of sodium citrate in kanamycin sulfate injection from a domestic factory is about 40 times higher than that of the Meiji formulation. Several specific impurities can be detected in solutions heated under simulated sterilization conditions (121 ℃), which were correlated with the amount of sodium citrate. Impurities were characterized by HPLC-MS/MS, and data showed that the identified impurities were interaction products of kanamycin and sodium citrate. These results indicate that greater attention should be directed at formula optimization in domestic factories, as it is crucial to the safety and efficacy of the preparations. Drug-excipient chemical compatibility should also be evaluated in the development of pharmaceutical dosages forms especially when the active pharmaceutical ingredients have a primary amine group.
ABSTRACT
Research on polymer impurities has always been important in the quality control of cephalosporins. Research on polymers in cephalosporins that lack active amino groups on the C-7 side chain has not been reported. Therefore, our study used cefazolin sodium, which is widely used in the clinic, as an example. The polymer in cefazolin sodium and its product "cefazolin sodium pentahydrate for injection" was analyzed by column switching liquid chromatography-high resolution mass spectrometry. Two polymer impurity peaks were detected and the possible structures of these polymers were suggested. Through two-dimensional liquid chromatography, the chromatographic peaks following Sephadex gel chromatography and high-performance gel chromatography were compared to those obtained by reverse high-performance liquid chromatography (HPLC) for cefazolin sodium as reported in the Chinese Pharmacopoeia. The HPLC method proves more suitable for polymer detection than Sephadex gel chromatography and high-performance gel chromatography. The method of polymer detection for cefazolin sodium was established using the method of related substances HPLC as described in the Chinese Pharmacopoeia.
ABSTRACT
@#To establish a method for the determination of formaldehyde and glyoxal simultaneously in varenicline tartrate active pharmaceutical ingredient (API) and its intermediate, formaldehyde and glyoxal were derivatized by 2, 4-dinitrophenylhydrazine (2,4-DNPH) to improve the HPLC retention and UV detection sensitivity. Separation was performed on a C8 (150 mm × 4.6 mm, 5 μm) column by linear gradient elution using acetonitrile and water as the mobile phase; the detective wavelength was set at 380 nm.Formaldehyde and glyoxal were quantitatively determined by an external reference method.Linear calibration was established for both formaldehyde and glyoxal in the range from 0.094 to 1.88 μg/mL.The detection and the quantification limits were 0.047 μg/mL (19 μg/g) and 0.094 μg/mL (38 μg/g), respectively.The recoveries were (95.0±1.1)% and (99.4 ± 2.6)% for formaldehyde and glyoxal, respectively.This method has been fully validated to be applicable to quantitative analysis of trace amount of formaldehyde and glyoxal in varenicline tartrate API and its intermediate.Test results demonstrated that the contents of both formaldehyde and glyoxal met the permitted daily exposure (PDE) limits for the finished products of varenicline tartrate API as well as its intermediate, though the glyoxal contents in the crude intermediates were likely to exceed the limit.The established method is valuable for the manufacturing process and quality control of varenicline tartrate.
ABSTRACT
@#To improve the standard of quality control of tazobactam and its preparations in China, national reference standard of tazobactam impurity A was developed. After tazobactam impurity A was synthesized, its structure was validated by infrared (IR), mass spectrometry (MS) and nuclear magnetic resonance (NMR), and its content uniformity and short-term stability were measured and investigated. Then, water content and residue on ignition of impurity A were determined, and its purity was determined using high performance liquid chromatography (HPLC) with 10 mmol/L ammonium acetate solution-acetonitrile (98∶2) as the mobile phase. Mass balance method was used to determine the content of the first batch of tazobactam impurity A national standard substance. Meanwhile, nuclear magnetic quantitative method was used to calculate the content, which was mutually verified with the mass balance method. The developed reference material of tazobactam impurity A is consistent with the maximum degradation impurity in tazobactam system applicability solution and the reference material of tazobactam related substance A contained in USP41. Within the 95% confidence range, the ratio of inter- and intra-bottle variance of impurity A after separation was 0.61 (< F0.05(11,12)), proving that the uniformity was satisfying. The contents of organic impurity, water content and inorganic impurity in impurity A were 0.90%, 1.24% and 0.25%, respectively. The content of impurity A was determined to be 97.6% by mass balance method, which was basically consistent with the result of nuclear magnetic quantitative method (97.1%). Under the condition of 25 °C, the area normalized purity of impurity A was 99.1% at 0, 3, 5 and 10 days, proving that the sample was stable at room temperature for 10 days. Finally the first batch of national standard substance of tazobactam impurity A was established successfully.
ABSTRACT
Methocarbamol is a central nervous system depressant with skeletal muscle relaxant properties indicated to treatspasms. During the synthesis of methocarbamol from guaifenesin, both potential known and an unknown impurity(0.05%–0.1%), high performance liquid chromatography) were observed. The later was separated using preparativeliquid chromatography. Upon the findings of the 1H nuclear magnetic resonance, Mass, and IR spectral analysis, theunknown impurity was designated as a β-isomer of methocarbamol [1-hydroxy-3-(2-methoxy phenoxy) propan-2-ylcarbamate]. The impurity isolation, its structure elucidation, and the potential formation mechanism are discussed.
ABSTRACT
The research and development of monoclonal antibodies (mAbs) is a rapidly developing field. From the first generation of murine mAbs to the fourth generation of fully human mAbs, the efficacy and safety of mAbs in the treatment of various diseases have been continuously improved. In order to regulate the development and evaluation of mAbs, drug regulatory agencies and pharmacopeias of America and China have tried to issue feasible test procedures and acceptance criteria for quality evaluation of mAbs and biosimilars. Mass spectrometry (MS) technique with high sensitivity, resolution, selectivity, and specificity has become an important tool to evaluate the quality characteristics of monoclonal antibody-related products or specify mAb quality. The research of MS-based monoclonal antibody study involves structure characterization, impurity analysis, pharmacokinetics/pharmacodynamics (PK/PD), etc. This review focuses on the current quality control requirements of mAb related products and the development of MS technique for mAb quality characterization and specification. It is expected to provide information and references for evaluating the quality of monoclonal antibodies under research and development.
ABSTRACT
@#HPLC method was used for the determination of related substances in (E)-4-[2-(4-chlorophenoxy)-2-methylpanoyloxy]-3-methoxyphenyl acrylic acid. The separation was achieved by Ultimate XB-C18 column (4.6 mm×150 mm,5 μm) with mobile phase composed of methanol-1% acetic acid water (70∶30) at a wavelength of 275 nm. The results showed that (E)-4-[2-(4-chlorophenoxy)-2-methylpanoyloxy]-3-methoxyphenyl acrylic acid with various intermediates and compulsory destruction of degradation products were well separated. The impurity limit in three batches of API was less than 0.1% and the main impurity C was isolated and identified. Within the range from 0.20 to 59.96 μg/mL, the mass concentration of impurity C has good linear relationship with the peak area (r=0.999 9). The control method of related substances for (E)-4-[2-(4-chlorophenoxy)-2-methylpanoyloxy]-3-methoxyphenyl acrylic acid was established by impurity reference method and self-high and low concentration comparison. Methodological validation can be used for the detection of related substances of (E)-4-[2-(4-chlorophenoxy)-2-methylpanoyloxy]-3-methoxyphenyl acrylic acid.
ABSTRACT
@#The high-purity impurity C was isolated and purified from a new anti-allergic drug, rupatifen, by nucleophilic substitution reaction with bromobutaric acid, and its structure was confirmed by IR, UV, MS, 1H NMR, 13C NMR, DEPT135°,HSQC, HMBC, and 1H-1HCOSY. The preparation process of impurity C in this study was simple and easy to obtain under mild conditions, with the purity of 99.0% and the yield of 25%-30%;and the sample met the target compound by structural confirmation. The preparation process and structure confirmation provided sufficient impurity C reference substance for impurity research of raw materials and preparations of rupatifen fumarate, which laid a solid foundation for quality research of new drugs.