A comparative evaluation of tray spacer thickness and repeat pour on the accuracy of monophasic polyvinyl siloxane impression material: In vitro study.

Purpose: This study was aimed to determine the effect of various tray spacer thickness and subsequent repeated pours on the accuracy and dimensional stability of the impression made from monophasic polyvinyl siloxane material. Materials and Methods: Custom trays with different spacer thickness (2, 4 and 6 mm) were used for making an impression of a master model simulating 3 unit fixed partial denture with monophasic polyvinyl siloxane material. These impressions were poured with die stone and repoured. Distance between the reference points were measured and subjected to statistical analysis. Result: Casts obtained from 1 st , 2 nd and 3 rd pour of the impression in 2, 4 and 6 mm spacer thickness tray have similar dimensional accuracy amongst each other and with the master model except in molar diameter and inter-abutment distances of cast obtained from 6 mm spacer thickness tray. Conclusion: The vertical distance of stone dies were decreased, whereas horizontal distance increased as the thickness of impression material is increased. There were statistically non-significant changes occurring among the repeated pours in 2, 4 and 6 mm spacer thickness. Clinical Implication: 2 and 4 mm spacer thickness are acceptable for making an impression for three unit fixed partial denture with monophasic polyvinyl siloxane material and it was not affected by two subsequent (1 st and 2 nd ) repeated pours.

Effect of 3 different medicament on dimensional stability and surface detail reproduction of polyvinyl siloxane impression material.

Aim:Surface detail reproduction and dimensional stability of Poly vinyl siloxane impression material is most important property for final success of fixed partial denture. Purpose: This study was carried out to determine the effect of retraction cord medicaments (epinephrine, aluminum chloride and ferric sulfate) on the dimensional accuracy and surface detail reproduction of polyvinyl siloxane impressions. Method and materials: Polyvinyl siloxane impressions were made of standardized metal dies (American Dental Association [ADA] specification No. 19) and was treated with 1 of the 3 retraction cord medicaments. Dimensional accuracy was evaluated by comparing the average length of a line in the impressions to the standard die. Surface detail reproduction was evaluated by viewing the impressions under low-angle illumination at 10X magnification. Reproduction was considered satisfactory if 2 of 3 horizontal lines were reproduced continuously. The dies were also evaluated under the microscope before the impression was made. Results: The medicaments did not significantly affect the dimensional stability. Aluminum chloride and ferric sulfate had an adverse effect on surface detail reproduction. Epinephrine had no effect. Discussion: The changes in dimensional accuracy were within ADA guidelines, the surface detail reproduction was modified such that the impression would be considered clinically unacceptable. For optimal results, care must be taken to remove all traces of these retraction cord medicaments prior to recording of a polyvinyl siloxane impression.

Dimensional accuracy and detail reproduction of two hydrophilic vinyl polysiloxane impression materials tested under different conditions.

Background and Objectives: A limitation of vinyl polysiloxane (VPS) impression materials is hydrophobicity, and manufacturers have added surfactants and labeled these new products as "hydrophilic." The purpose of this investigation was to evaluate and compare the dimensional accuracy and surface detail reproduction of two hydrophilic VPS impression materials under dry, moist, and wet conditions. Materials and Methods: Ten impressions were made under dry, moist, and wet conditions respectively, with monophase, and regular body VPS impression material using a stainless steel metal die similar to that described in American Dental Association (ADA) specification 19, with lines scribed on it. Dimensional accuracy was measured by comparing the average length of the middle horizontal line in each impression to the same line on the metal die, by using a measuring microscope. The surface detail was evaluated. A one-way analysis of variance and Student t-test were used to compare mean dimensional changes (α = 0.05). Results: Conditions (dry, moist, and wet) did not cause significant adverse effects on the dimensional accuracy of either material. The mean dimensional changes were 0.00084% (+0.00041%) for monophase and 0.00119% (+0.00033%) for regular body. Monophase material was satisfactory in detail reproduction 100% of the time in dry conditions, 90% in moist, and only 20% in wet conditions. The regular body showed 100% satisfactory impressions in dry, 80% in moist, and 10% in wet conditions. With the additional smooth surface evaluation, only under dry conditions impressions with clinically acceptable surface quality were produced. Conclusions: Dimensional changes for both materials were well within ADA standards of minimal shrinkage value of 0.5%.

Influence of retentive areas associated to onlay preparations on the dimensional stability of silicone impression materials

This study evaluated the effect of retentive areas on onlay preparations on the dimensional alterations in condensation and addition silicone materials. A standard model with an onlay preparation was made. Each impression material was used through the double or simultaneous impression technique (n=25), resulting in a hundred impressions of the same model. Impressions were poured with type IV dental stone. Digital images were taken with a light microscope and the distances between the reference points created on the plaster dies were compared with the ones on the standard model. In the occlusal, mesial-medium and mesial-cervical segments, the double impression (DI) with condensation silicone presented similar values compared to the standard model. The values of the addition silicone with DI were similar to the standard model only in the mesial-occlusal segment. In the other segments (distal-cervical, distal-medium and distal-occlusal), all groups were statistically different from the control. It could be concluded that addition and condensation silicone impressions provided plaster dies with significant dimensional alterations in most of the evaluated areas when compared to the standard model. The retentive areas related to the onlay preparation influenced the dimensional stability of the addition and condensation silicone impressions.

Este estudo avaliou as alteracoes dimensionais de silicones de condensacao e adicao usados em duas tecnicas como resultado de areas retentivas de preparos do tipo onlay. Um modelo padrao foi feito e vinte e cinco moldagens realizadas com os dois materiais, atraves da tecnica de dupla impressao ou impressao simultanea, e cada material resultou em 50 modelos de gesso. Imagens digitais foram feitas com um microscopio de luz e as distancias entre os pontos de referencia criados no modelo de gesso foram comparados aos pontos de referencia no modelo padrao. Nos segmentos oclusais, medio-mesial e cervico-mesial, a tecnica de dupla impressao (DI) com silicone de condensacao apresentou valores similares comparados ao modelo padrao. Os valores do silicone de adicao com DI foram similares ao modelo padrao somente no segmento mesio-oclusal. Nos outros segmentos (disto-cervical, medio-distal e disto-oclusal), todos os grupos foram estatisticamente diferentes do controle. Pode- se concluir que moldagens com silicone de adicao e condensacao conferem modelos de gesso com alteracoes dimensionais significativas na maioria das areas avaliadas, quando comparadas ao modelo padrao. As areas retentivas relacionadas ao preparo de onlay influenciaram na estabilidade dimensional das moldagens atraves dos silicones de condensacao e adicao.

WETTABILITY OF POLYVINYLSILOXANE IMPRESSION MATERIALS AND IMPROVED STONE MATERIALS / 대한치과보철학회지

Wettability of addition silicone impression material is very important property for making an accurate restoration. This study examined the impression quality in clinical condition and the wet tability of impression and die material. Four commercially available addition silicone impression material (Express, Examix, Contrast, Perfect) and three die materials (Die-Keen, Vel-Mix, FujiRock) were studied. A total of 50 putty/wash and heavy body/wash impressions of wet intact permanent molar teeth were examined for definition of the gingival sulcus reproduction and then classified in quality ranking. The percentage of the sulcus reproduction ability of each material was calculated from the sulcus depths of cross-sectioned epoxy resin casts from the impressions and clinically measured sulcus depths. The same impression materials were used to produce 3 groups of die stone casts form void entrapment die had been exposed to milk. Voids in the impression. body and stone casts were counted under a stereoscopic microscope. From the experiment, the following results were obtained 1. Sulcus reproduction ability of additional silicone impression material were diminished in order of Express, Examix, Perfect, Contrast. The significant difference was found between Perfect and other material. Heavy body/wash combination was superior to putty/wash method in Perfect impression material. 2. In direct observation, bontrast showed least void in impression body but correlations were not found between sulcus reproduction and void production. 3. In void entrapment laboratory test, wettability were diminished in order of Examix, Contrast, Express, Perfect. Clinical impression recording seems not to correlate with laboratory test. 4. The wettability of die material to impression material was not different in Express, Examix, Contrast. But, in Perfect, Die-Keen had superior wettability to others.