Study on quantitative analysis of bracket-induced nonlinear response of labio-cheek soft tissue during the orthodontic process / 生物医学工程学杂志

In the orthodontics process, intervention and sliding of an orthodontic bracket during the orthodontic process can arise large response of the labio-cheek soft tissue. Soft tissue damage and ulcers frequently happen at the early stage of orthodontic treatment. In the field of orthodontic medicine, qualitative analysis is always carried out through statistics of clinical cases, while quantitative explanation of bio-mechanical mechanism is lacking. For this purpose, finite element analysis of a three-dimensional labio-cheek-bracket-tooth model is conducted to quantify the bracket-induced mechanical response of the labio-cheek soft tissue, which involves complex coupling of contact nonlinearity, material nonlinearity and geometric nonlinearity. Firstly, based on the biological composition characteristics of labio-cheek, a second-order Ogden model is optimally selected to describe the adipose-like material of the labio-cheek soft tissue. Secondly, according to the characteristics of oral activity, a two-stage simulation model of bracket intervention and orthogonal sliding is established, and the key contact parameters are optimally set. Finally, the two-level analysis method of overall model and submodel is used to achieve efficient solution of high-precision strains in submodels based on the displacement boundary obtained from the overall model calculation. Calculation results with four typical tooth morphologies during orthodontic treatment show that: ① the maximum strain of soft tissue is distributed along the sharp edges of the bracket, consistent with the clinically observed profile of soft tissue deformation; ② the maximum strain of soft tissue is reduced as the teeth align, consistent with the clinical manifestation of common damage and ulcers at the beginning of orthodontic treatment and reduced patient discomfort at the end of treatment. The method in this paper can provide reference for relevant quantitative analysis studies in the field of orthodontic medical treatment at home and abroad, and further benefit to the product development analysis of new orthodontic devices.

Comparative evaluation of three methods of adhesive remnant removal after orthodontic bracket debonding

ABSTRACT Objective: This study aimed to assess the effects of three methods of adhesive remnant removal (carbide bur and low speed handpiece, carbide bur and high speed handpiece, and zircon-rich glass fiber reinforced composite bur), after orthodontic bracket debonding, on tooth color and enamel surface roughness. Methods: Ninety sound premolar teeth were selected. The baseline tooth color was assessed using Vita spectrophotometer. The teeth were subjected to bracket bonding processes and then randomly divided into three equal groups. In each group, composite remnant was removed by one of the three methods of adhesive removal, and the teeth were then subjected to color assessment again. To measure the surface roughness, a scanning electron microscope (SEM) with x400 magnification was used. Results: ANOVA showed that the effect of the three methods of adhesive remnant removal on ∆L, ∆b and ∆E was statistically significant (p=0.01), but without significant effect on ∆a. Comparison of the means showed that composite bur and high speed carbide bur yielded the highest ∆E (p=0.05), and had a significant difference when compared to carbide bur and low speed handpiece. The highest ∆L and ∆b values belonged to samples approached with composite bur and carbide bur with high speed handpiece, respectively. SEM analysis showed that the composite bur created a very smooth surface, compared to the other two methods. Conclusion: Zircon-rich glass fiber reinforced composite created the smoothest enamel surface and highest color change, when compared to the other two methods.

RESUMO Objetivo: O presente estudo teve como objetivo avaliar os efeitos de três métodos de remoção de adesivo remanescente (broca carbide e peça de mão em baixa rotação, broca carbide e peça de mão em alta rotação, e broca de compósito reforçado com fibra de vidro rica em zircônia), após a descolagem de braquetes ortodônticos, sobre a cor dos dentes e rugosidade superficial do esmalte. Métodos: Noventa pré-molares hígidos foram selecionados. A cor inicial dos dentes foi avaliada usando um espectrofotômetro Vita. Os dentes foram submetidos à etapa de colagem dos braquetes e, então, divididos aleatoriamente em três grupos. Em cada grupo, o adesivo remanescente foi removido usando um dos três métodos de remoção, e os dentes foram novamente submetidos à avaliação de cor. Para medir a rugosidade superficial dos dentes, foi usado um microscópio eletrônico de varredura (MEV) com aumento de 400x. Resultados: A ANOVA mostrou que os três métodos de remoção do adesivo remanescente tiveram efeito estatisticamente significativo (p=0,01) em ∆L, ∆b e ∆E, mas sem efeito significativo em ∆a. A comparação das médias mostrou que a broca de compósito e a broca carbide em alta rotação produziram o maior ∆E (p=0,05) e tiveram uma diferença significativa quando comparadas com a broca carbide e a peça de mão em baixa rotação. Os maiores valores de ∆L e ∆b foram encontrados, respectivamente, nos grupos com broca de compósito e broca carbide usando peça de mão em alta rotação. A análise MEV mostrou que o uso da broca de compósito resultou em uma superfície muito lisa, em comparação com os outros dois métodos. Conclusão: Em comparação aos outros métodos, a broca de compósito reforçado com fibra de vidro rica em zircônia criou a superfície de esmalte mais lisa e resultou em uma maior mudança de cor.

Análisis comparativo in vitro de la resistencia adhesiva al cizallamiento de brackets metálicos adheridos a superficies dentarias tratadas con diferentes agentes blanqueadores / Comparative in vitro analysis of the adhesive resistance to the shear bond strength of metal brackets adhered to dental surfaces treated with different bleaching agents

RESUMEN: Objetivo: Evaluar y comparar el efecto de tres agentes blanqueadores en la resistencia adhesiva al cizallamiento de brackets metálicos. Método: Se cementaron 76 brackets en premolares humanos extraídos por indicación de ortodoncia. Se establecieron 4 grupos: (0) control, (1) esmalte tratado con Peróxido de Carbamida al 16%, (2) Peróxido de Hidrógeno al 35% y (3) tiras de blanqueamiento con Peróxido de Hidrógeno al 10%. Los brackets fueron cementados con Transbond XT (3M Unitek, EE.UU.). Se realizaron 5.000 ciclos de termociclado, luego se evaluó la resistencia adhesiva mediante una máquina Bisco y la cantidad de material adhesivo remanente según el índice adhesivo remanente (ARI). El análisis estadístico incluyó pruebas de Shapiro- Wilk, Kruskal -Wallis y Mann-Whitney. Resultados: Los grupos 0, 1, 2, 3 obtuvieron fuerzas de resistencia de 12.64, 11.06, 6.4 y 9.34 Mpa respectivamente con diferencia estadística entre los grupos (p <0.05). El ARI fue significativamente diferente en algunos grupos (p <0.05), indicando fallas adhesivas para el grupo 2 (p <0.05), cohesivas para el grupo control y de ambos tipos para los grupos 1 y 3. Conclusiones: El peróxido de hidrógeno al 35% reduce la resistencia adhesiva al cizallamiento en brackets metálicos sometidos a termociclado 24 horas luego del blanqueamiento.

ABSTRACT: Aim: To evaluate and compare the effect of three bleaching agents on the shear bond strength of metallic brackets. Method: Brackets were cemented on 76 human premolars extracted for orthodontic reasons. 4 groups were evaluated: (0) Control, (1) enamel treated with Carbamide Peroxide 16%, (2) Hydrogen Peroxide 35% and (3) Hydrogen Peroxide 10% "Whitening strips". All brackets were cemented using Transbond XT adhesive system (3M, Unitek, USA). All samples were thermocycled (5.000 cycles). Shear bond strength was evaluated with a Bisco machine and the amount of adhesive material at the base of the brackets and enamel surface was assessed using the adhesive remnant index (ARI). The statistical analysis included Shapiro-Wilk, Kruskal-Wallis and Mann-Whitney U tests. Results: The results of shear bond strength for groups 0, 1, 2, and 3 were 12.64, 11.06, 6.4 and 9.34 MPa respectively, with statistically significant differences between groups (p <0.05). ARI index was significantly different in some groups (p <0.05), indicating cohesive failure for control, adhesive failure for group 2 (p <0.05), adhesive and cohesive failure for groups 1 and 3. Conclusions: The 35% hydrogen peroxide office bleaching agent reduces adhesion values in the metal brackets thermocycled 24 hours after bleaching.

Influence of radiant exposure values from two third generation LED curing units on polymerization profile and microhardness of orthodontic composite under ceramic and metallic brackets

ABSTRACT Introduction: Third generation of LED light curing units might be used in short exposure periods for orthodontic brackets bonding. Objective: This study evaluated the effect of the different radiant exposure (RE) values: Manufacturers' instructions (MI), ½ MI, 1/4 MI and Turbo mode. Two third-generation LED curing units were used: VALO® and Bluephase 20i® . The degree of conversion (DC) and Vickers hardness (VHN) of an orthodontic composite (OC) (Transbond XT) under metallic (MB) or ceramic brackets (CB) were measured. Methods: OC was applied to the bracket base, which was then placed over an attenuated total reflectance (ATR) table coupled to an infrared light spectroscope, or to a glass surface for the VHN analysis. The specimens were light-cured and DC values were calculated. The VHN was obtained in a microhardness tester. The data were analyzed with 2-way ANOVA followed by Tukey's post-hoc test (pre-set α=0.05). Linear regression analysis evaluated the relationship between RE values and dependent variables. Results: CB allowed higher DC and VHN values than MB (p< 0.001). No significant difference was noted among groups when CB were used. For MB, MI groups showed the highest DC and VHN values. A significant, but weak relationship was found between delivered RE values and dependent variables. Conclusions: The decrease in RE values from third generation LED CU did not jeopardize the DC values when CB were used, but can compromise DC and VHN values when MB are used.

RESUMO Introdução: A terceira geração de LEDs fotopolimerizadores pode ser utilizada em curtos períodos de exposição para a colagem de braquetes ortodônticos. Objetivo: O presente estudo avaliou o efeito dos diferentes valores de irradiância (IR): instruções do fabricante (IF), ½ IF, » IF e modo Turbo. Dois fotopolimerizadores LED de terceira geração (VALO® e Bluephase20i®) foram utilizados. Foram mensurados o grau de conversão (GC) e a dureza Vickers (VHN) de um compósito ortodôntico (CO) (Transbond XT) sob braquetes metálicos (BM) ou cerâmicos (BC). Métodos: O compósito ortodôntico foi aplicado na base do braquete e foi posicionado sobre uma mesa de refletância total atenuada (ATR) acoplada a um espectroscópio de infravermelho ou a uma superfície de vidro para análise de VHN. As amostras foram fotopolimerizadas e os valores de GC foram calculados. O VHN foi obtido em um microdurômetro. Os dados foram analisados com ANOVA de 2 fatores seguida do teste post-hoc de Tukey (predefinido α = 0,05). A análise de regressão linear avaliou a relação entre os valores de IR e as variáveis dependentes. Resultados: BC permitiu valores maiores de GC e VHN do que BM (p<0,001). Nenhuma diferença significativa foi observada entre os grupos quando BC foi utilizado. Para BM, os grupos de IF mostraram os maiores valores de GC e VHN. Uma relação significativa, mas fraca, entre os valores de IR entregue e as variáveis dependentes foi encontrada. Conclusões: A diminuição dos valores de IR dos fotopolimerizadores LED de terceira geração não prejudicou os valores de GC quando BC foram utilizados, mas pode comprometer os valores de GC e VHN quando BM são utilizados.

Effect of Fixed Orthodontic Appliances on Subgingival Plaque Microbiota

Introduction: The present study aimed to examine changes insubgingival microbiota and clinical parameters before and afterplacement of bracket.Methods: Clinical parameters such as plaque index (PI),probing depth (PD), bleeding on probing (BOP), clinicalattachment level (CAL), and gingival index (GI) were recorded.Additionally, subgingival microbial samples were collected from30 individuals aged between 13 and 25.A total of 15 individualsas the control group were matched in terms of age and sexwithout needing orthodontic treatment using specific primers.Furthermore, SYBER Green Real-Time PCR was conducted todetermine bacterial flora in stored samples. All the mentionedprocedures were reexamined in the experimental and controlgroups three months after band and bracket bonding. Adescriptive analysis was conducted, and paired t-test andWilcoxon test were employed for differences between thegroups (P<0.05).Results: No changes in the level of clinical attachment wereseen, but scores for plaque index, bleeding on probing andgingival index increased 3 months after placement of bracketin the experimental group (P<0.05). P. nigrescence in theexperimental group increased after placement of bracketscompared to the control group, but P. gingivalis and T.Denticola proportions increased.Conclusions: Fixed orthodontic appliances may raise thegrowth of periodontopathogenic bacteria and consequentlyleads to gingival inflammation without destructive effect ondeep periodontal tissues.

Comparison of bond strengths of ceramic brackets bonded to zirconia surfaces using different zirconia primers and a universal adhesive

OBJECTIVES: The aim of this study is to compare the shear bond strengths of ceramic brackets bonded to zirconia surfaces using different zirconia primers and universal adhesive. MATERIALS AND METHODS: Fifty zirconia blocks (15 × 15 × 10 mm, Zpex, Tosoh Corporation) were polished with 1,000 grit sand paper and air-abraded with 50 µm Al2O3 for 10 seconds (40 psi). They were divided into 5 groups: control (CO), Metal/Zirconia primer (MZ, Ivoclar Vivadent), Z-PRIME Plus (ZP, Bisco), Zirconia Liner (ZL, Sun Medical), and Scotchbond Universal adhesive (SU, 3M ESPE). Transbond XT Primer (used for CO, MZ, ZP, and ZL) and Transbond XT Paste was used for bracket bonding (Gemini clear ceramic brackets, 3M Unitek). After 24 hours at 37°C storage, specimens underwent 2,000 thermocycles, and then, shear bond strengths were measured (1 mm/min). An adhesive remnant index (ARI) score was calculated. The data were analyzed using one-way analysis of variance and the Bonferroni test (p = 0.05). RESULTS: Surface treatment with primers resulted in increased shear bond strength. The SU group showed the highest shear bond strength followed by the ZP, ZL, MZ, and CO groups, in that order. The median ARI scores were as follows: CO = 0, MZ = 0, ZP = 0, ZL = 0, and SU = 3 (p < 0.05). CONCLUSIONS: Within this experiment, zirconia primer can increase the shear bond strength of bracket bonding. The highest shear bond strength is observed in SU group, even when no primer is used.

Influence of Thermal Cycles Number on Bond Strength of Metallic Brackets to Ceramic

Abstract The aim of this study was to evaluate the effect of different number of thermal cycles on the shear bond strength (SBS) of metallic orthodontic brackets bonded to feldspathic ceramic by a composite resin. Twenty-five ceramic cylinders were etched with 10% hydrofluoric acid for 60 s and received two layers of silane. Brackets were bonded to the cylinders using Transbond XT and assigned to 5 groups (n=5): Group 1 - Control group (without thermal cycling); Group 2 - 500 thermal cycles; Group 3 - 5,000 thermal cycles; Group 4 - 7,000 thermal cycles and Group 5 - 10,000 thermal cycles. Light-activation was carried out by Radii Plus LED. SBS testing was carried out after 24 h of storage in deionized water and thermal cycling (5/55 oC and 30 s dwell time). Five brackets were bonded to each cylinder, totalizing 25 brackets for each group. Data were submitted to one-way ANOVA and Tukey’s test (α=0.05). The Adhesive Remnant Index (ARI) was evaluated at 8× magnification. The SBS (MPa) of control group (9.3±0.8), 500 (9.0±0.7) and 5,000 (8.4±0.9) thermal cycles were significantly higher than those after 7,000 (6.8±0.6) and 10,000 (4.9±1.0) thermal cycles (p<0.05). The ARI showed a predominance of Scores 0 (adhesive failure) prevailed in all groups, as shown by the ARI, with increased scores 1 and 2 (mixed failures) for control group and 500 thermal cycles. In conclusion, thermal fatigue may compromise the bonding integration between metallic brackets and ceramic restorations. For in vitro testing, use of at least 7,000 cycles is advised to result in significant fatigue on the bonding interface.

Resumo O objetivo neste estudo foi avaliar o efeito de diferentes números de ciclos térmicos na resistência da união de braquetes metálicos à cerâmica feldspática usando resina composta. Vinte e cinco cilindros de cerâmica foram condicionados com ácido fluorídrico a 10% por 60 s e duas camadas de silano. Braquetes foram fixados nos cilindros usando Transbond XT e depois separados em 5 grupos (n=5): Grupo 1 - Grupo Controle (sem ciclagem térmica); Grupo 2 - 500 ciclos térmicos; Grupo 3 - 5.000 ciclos térmicos; Grupo 4 - 7.000 ciclos térmicos e Grupo 5 - 10.000 ciclos térmicos. A fotoativação foi realizada com aparelho LED Radii Plus. O ensaio de resistência de união ao cisalhamento foi realizado após armazenagem por 24 h em água deionizada ou após a ciclagem térmica (5º/55 ºC, com banhos de 30 s cada). Cinco braquetes foram fixados em cada cilindro, totalizando 25 bráquetes por grupo. Os dados foram submetidos à análise de variância de um fator e ao teste de Tukey (α=0,05). O Índice de Remanescente Adesivo (IRA) foi avaliado com aumento de 8x. Os valores de resistência (MPa) dos grupos controle (9,3±0,8), 500 (9,0±0,7) e 5.000 (8,4±0,9) ciclos térmicos foram significantemente maiores do que os grupos submetidos à 7.000 (6,8±0,6) e 10.000 (4,9±1,0) ciclos térmicos (p<0,05). O IRA mostrou predominância do escore 0 para todos os grupos, com aumento de escores 1 e 2 para os grupos controle e submetidos a 500 ciclos térmicos. Em conclusão, a fadiga térmica pode comprometer a união entre os braquetes metálicos e as restaurações cerâmicas. Para testes in vitro, o uso de pelo menos 7.000 ciclos é recomendado para determinar fadiga significante na interface de união.

Research of design and manufacturing technology of titanium personalized orthodontic bracket / 口腔疾病防治

Objective @# A titanium personalized orthodontic bracket is designed and manufactured using the technology of computed tomography (CT), computer aided design (CAD), finite element analysis (FEA), and selective laser melting (SLM) to well match the patient tooth so as to realize mold-free manufacturing. @*Methods@#A model of a titanium personalized orthodontic bracket which is built by CT scanning machine and Pro/E software, is imported into Ansys software to carry out finite element simulation analysis with nonlinear contact method. Then, the titanium personalized orthodontic bracket is proposed after the model data above is imported to SLM molding equipment via titanium powder melted with layer by layer using a high-speed scanning galvanometer. @*Results @#The maximum equivalent stress of the titanium personalized orthodontic bracket is distributed uniformly and reasonably, the titanium personalized orthodontic bracket formed by SLM molding equipment can provide high accuracy and there is a high similarity between the bottom of the orthodontic bracket and the tooth surface shape.@*Conclusion @#The combination of CT, CAD, FEA, SLM technology can fulfill model-free manufacturing of the personalized orthodontic bracket and thus shorten the manufacturing cycle.

Cleansing orthodontic brackets with air-powder polishing: effects on frictional force and degree of debris

ABSTRACT Introduction: Debris buildup on the bracket-wire interface can influence friction. Cleansing brackets with air-powder polishing can affect this process. Objective: The aim of this study was to evaluate the frictional force and amount of debris remaining on orthodontic brackets subjected to prophylaxis with air-powder polishing. Methods: Frictional force and debris buildup on the surface of 28 premolar brackets were evaluated after orthodontic treatment. In one hemiarch, each bracket was subjected to air-powder polishing (n = 14) for five seconds, while the contralateral hemiarch (n = 14) served as control. Mechanical friction tests were performed and images of the polished bracket surfaces and control surfaces were examined. Wilcoxon test was applied for comparative analysis between hemiarches at p < 0.05. Results: Brackets that had been cleaned with air-powder polishing showed lower friction (median = 1.27 N) when compared to the control surfaces (median = 4.52 N) (p < 0.01). Image analysis showed that the control group exhibited greater debris buildup (median = 2.0) compared with the group that received prophylaxis with air-powder polishing (median = 0.5) (p < 0.05). Conclusion: Cleansing orthodontic brackets with air-powder polishing significantly reduces debris buildup on the bracket surface while decreasing friction levels observed during sliding mechanics.

RESUMO Introdução: o acúmulo de detritos na interface braquete-arco pode influenciar no atrito, mas a limpeza dos braquetes usando jatos de bicarbonato de sódio pode interferir nesse processo. Objetivo: o objetivo desse estudo foi avaliar a força de atrito e a quantidade de detritos remanescentes em braquetes ortodônticos submetidos à profilaxia com jatos de bicarbonato de sódio. Material e Métodos: avaliou-se, ao final do tratamento ortodôntico, a força de atrito e o acúmulo de detritos na superfície de 28 braquetes de pré-molares. Em uma hemiarcada, os braquetes foram jateados com bicarbonato de sódio (n = 14) por 5 segundos, enquanto a hemiarcada contralateral serviu de controle (n = 14). Foram realizados ensaios mecânicos de atrito e análise imagiológica dos braquetes de ambas as hemiarcadas, a jateada e a controle. O teste de Wilcoxon foi utilizado para a análise comparativa entre as hemiarcadas, com p < 0,05. Resultados: os braquetes submetidos à limpeza com jatos de bicarbonato de sódio apresentaram menor atrito (mediana = 1,27N), quando comparados aos do lado controle (mediana = 4,52N) (p < 0,01). A análise imagiológica demonstrou que o grupo controle apresentou maior acúmulo de detritos (mediana = 2,0), em comparação ao grupo que recebeu profilaxia com jatos de bicarbonato (mediana = 0,5) (p < 0,05). Conclusão: a limpeza dos braquetes ortodônticos por meio do jateamento com bicarbonato de sódio reduz significativamente o acúmulo de detritos na superfície deles, bem como os níveis de atrito observados durante a mecânica de deslizamento.

Translucency and color match with a shade guide of esthetic brackets with the aid of a spectroradiometer

ABSTRACT Objective: Since the color of esthetic brackets should match that of teeth, the aims of this study were to determine the color and translucency of esthetic brackets by means of the clinically relevant use of a spectroradiometer, and to compare the color of brackets with that of a commercial shade guide. Methods: The color of central and tie-wing regions of four plastic and four ceramic brackets was measured according to the CIE L*a*b* color scale over white and black backgrounds. Brackets were classified into five groups based on their composition. The color of Vitapan Classical Shade Guide tabs was also measured. Translucency parameter (TP) and contrast ratio (CR) were calculated to determine translucency. Results: Color differences between brackets and the shade guide tabs were 10.4 - 34.5 ∆E*ab units. TP and CR values for the central region were 16.4 - 27.7 and 0.38 - 0.58, whereas for the tie-wings they were 24.0 - 39.9 and 0.25 - 0.45, respectively. The color coordinates, TP and CR values were significantly influenced by bracket composition and brand (p < 0.05). Conclusions: Esthetic brackets investigated herein showed unacceptable color differences (∆E*ab > 5.5) compared with the shade guide tabs. Differences in the translucency of brackets by brand were within the visually perceptible range (∆CR > 0.07). Therefore, brackets showing the best matching performance for each case should be selected considering esthetic and functional demands.

RESUMO Objetivo: considerando-se que a cor dos braquetes estéticos deve corresponder à cor dos dentes, os objetivos do presente estudo foram determinar a cor e a translucidez de braquetes estéticos, por meio do uso clinicamente relevante de um espectroradiômetro, e comparar a cor desses braquetes com a cor de uma escala comercial de cores. Métodos: a cor das regiões central e da aleta de quatro braquetes plásticos e quatro braquetes cerâmicos foi medida segundo o sistema de cores CIE L*a*b*, sobre fundos branco e preto. Os braquetes foram classificados em cinco grupos, de acordo com a sua composição. A cor das peças da escala de cores Vitapan Classical(r) também foi medida. O parâmetro de translucidez (PT) e a razão de contraste (RC) foram calculados para se determinar a translucidez. Resultados: as diferenças de cor entre os braquetes e as peças da escala de cores variaram de 10,4 a 34,5 unidades ∆E*ab. Os valores de PT e RC, respectivamente, variaram de 16,4 a 27,7 e de 0,38 a 0,58 na região central; já para a região das aletas, esses valores variaram de 24,0 a 39,9 e de 0,25 a 0,45. As coordenadas de cor e os valores de PT e RC foram significativamente influenciados pela marca e composição dos braquetes (p < 0,05). Conclusões: os braquetes estéticos investigados nesse estudo demonstraram diferenças de cor inaceitáveis (∆E*ab > 5,5), quando comparados às peças da escala de cores. As diferenças de translucidez entre as marcas de braquetes estavam dentro do limite visualmente perceptível (∆RC > 0,07). Portanto, ao selecionar os braquetes com a melhor correspondência de cor, deve-se levar em consideração as exigências estéticas e funcionais de cada caso.

Influence of Light Source, Thermocycling and Silane on the Shear Bond Strength of Metallic Brackets to Ceramic

The objective of this study was to evaluate the effects of different light sources, thermocycling and silane on the bond strength of metallic brackets to ceramic. Cylinders of feldspathic ceramic were etched with 10% hydrofluoric acid for 60 s. Half of the cylinders (Groups 1 to 4) received two layers of silane. Metallic brackets were bonded to the cylinders using Transbond XT and divided into 8 groups (n=20), according to light source (Radii Plus LED - 40 s; Groups 1, 2, 5 and 6 and XL 2500 halogen light - 40 s; Groups 3, 4, 7 and 8) and experimental conditions with (Groups 2, 4, 6 and 8) without thermocycling (Groups 1, 3, 5 and 7). Shear bond testing was carried out after 24 h of deionized water storage (Groups 1, 3, 5 and 7) and thermocycling (Groups 2, 4, 6 and 8; 7,000 cycles - 5°/55 °C). Date were submitted to three-way ANOVA and Tukey's post hoc test (α=0.05). The Adhesive Remnamt Index (ARI) was evaluated at 8× magnification. The application of silane was effective in increasing the shear bond strength of the brackets to ceramic (p<0.05). Significant difference (p<0.05) on the bond strength was observed between light sources with or without thermocycling. The ARI showed a predominance of scores 0 for all groups, with an increase in scores 1, 2 and 3 for the silane groups. In conclusion, silane improved significantly the shear bond strength of the brackets to ceramic. The thermocycling and light sources influence on the bond strength.

Resumo O objetivo neste estudo foi avaliar o efeito de diferentes fontes de luz, termociclagem e silano na resistência de união de bráquetes metálicos a cerâmica feldspática. Cilindros de cerâmica feldspática foram condicionados com ácido fluorídrico a 10% por 60 s. Metade dos cilindros (Grupos 1 a 4) recebeu duas camadas de silano. Bráquetes metálicos foram colados aos cilindros usando Transbond XT (3M Unitek), formando 8 grupos (n=20), dependendo das fontes de luz usadas para fotoativação (Radii Plus LED - 40s; Grupos 1, 2, 5 e 6 e XL 2500 halógena - 40 s; Grupos 3, 4, 7 e 8), nas condições experimentais com (Grupos 2, 4, 6 e 8) e sem ciclagem térmica (Grupos 1, 3, 5 e 7). O ensaio de resistência ao cisalhamento foi realizado após armazenagem por 24 h em água deionizada (Grupos 1, 3, 5 e 7) ou armazenados e submetidos a ciclagem térmica (Grupos 2, 4, 6 e 8; 7.000 ciclos - 5° e 55° C). Os dados foram submetidos à Análise de Variância de três fatores e teste de Tukey (α=0,05). O Índice de Remanescente Adesivo (IRA) foi avaliado com aumento de 8×. O uso do silano foi efetivo no aumento da resistência de união ao cisalhamento de bráquetes à cerâmica. Diferença significante na resistência de união foi observada entre as fontes de luz, e com ou sem ciclagem térmica. O IRA mostrou predominância de escore 0 para todos os grupos, com aumento de escores 1, 2 e 3 para os grupos com silano. Em conclusão, a aplicação do silano melhorou significativamente a resistência de união ao cisalhamento de bráquete à cerâmica. A ciclagem térmica e as fontes de luz influenciaram a resistência da união.

Influence of Water Storage and Bonding Material on Bond Strength of Metallic Brackets to Ceramic

Abstract: This study investigated the influence of water storage (24 h and 6 months), and Transbond XT and Fuji Ortho LC bonding materials on the bond strength of metallic brackets bonded to feldspathic ceramic. Four cylinders of feldspathic ceramic were etched with 10% hydrofluoric acid for 60 s. Each cylinder received two layers of silane. Metallic brackets were bonded to the cylinders using Transbond XT or Fuji Ortho LC. Light-activation was carried out with 40 s total exposure time using Bluephase G2. Half the specimens for each bonding materials (n=20) were stored in distilled water at 37 °C for 24 h and the other half for 6 months. Shear bond strength testing was performed after storage times at a crosshead speed of 1 mm/min. The adhesive remnant index (ARI) was used to evaluate the amount of adhesive remaining on the ceramic surface at ×8 magnification. Data were subjected to two-way ANOVA and Tukey's test (p<0.05). Transbond XT showed significantly higher bond strength (p<0.05) than Fuji Ortho LC. Significant differences in bond strength (p<0.05) were found when 24 h and 6 months storage times were compared between materials. ARI showed a predominance of score 0 for all groups, and higher scores at 1, 2 and 3 for 24 h storage time. In conclusion, storage time and bonding materials showed significant influence on the bond strength of brackets to ceramic.

Resumo: Este estudo investigou a influência da armazenagem em água (24 h e 6 meses) e dos materiais para colagem Transbond XT e Fuji Ortho LCO na resistência da união de bráquetes metálicos fixados a cerâmica feldspática. Quatro cilindros de cerâmica foram condicionados com ácido fluorídrico a 10% por 60 s. Todos os cilindros receberam duas camadas de silano. Bráquetes metálicos foram fixados aos cilindros utilizando os materiais Transbond XT ou Fuji Ortho LC. A fotoativação foi realizada com tempo de exposição total de 40 s utilizando Bluephase G2. Metade das amostras de cada material de colagem (n=20) foi armazenada em água destilada a 37 °C por 24 h e outra metade por 6 meses. O ensaio de resistência da união ao cisalhamento foi realizado após os períodos de armazenagem à velocidade de 1 mm/minuto. O Índice de Remanescente Adesivo (IRA) foi utilizado para avaliar a quantidade de adesivo residual na superfície da cerâmica, em lupa estereoscópica com aumento de 8x. Os dados foram submetidos à Análise de Variância de dois fatores e teste de Tukey (p<0,05). Transbond XT apresentou resistência de união significativamente maior do que Fuji Ortho LC. Diferença significante (p<0,05) na resistência da união foi encontrada entre os períodos de armazenagem, qualquer que fosse o material para colagem. O IRA mostrou predominância de escore 0 para todos os grupos, com aumento de escores 1, 2 e 3 para o período de armazenagem de 24 h. Em conclusão, o período de armazenagem e os materiais de colagem influenciaram significativamente a resistência da união de bráquetes à cerâmica.

Retrieval analysis of different orthodontic brackets: the applicability of electron microprobe techniques for determining material heterogeneities and corrosive potential

OBJECTIVE: The objective of this study was to investigate the applicability of micro-analytical methods with high spatial resolution to the characterization of the composition and corrosion behavior of two bracket systems. MATERIAL AND METHODS: The surfaces of six nickel-free brackets and six nickel-containing brackets were examined for signs of corrosion and qualitative surface analysis using an electron probe microanalyzer (EPMA), prior to bonding to patient's tooth surfaces and four months after clinical use. The surfaces were characterized qualitatively by secondary electron (SE) images and back scattered electron (BSE) images in both compositional and topographical mode. Qualitative and quantitative wavelength-dispersive analyses were performed for different elements, and by utilizing qualitative analysis the relative concentration of selected elements was mapped two-dimensionally. The absolute concentration of the elements was determined in specially prepared brackets by quantitative analysis using pure element standards for calibration and calculating correction-factors (ZAF). RESULTS: Clear differences were observed between the different bracket types. The nickel-containing stainless steel brackets consist of two separate pieces joined by a brazing alloy. Compositional analysis revealed two different alloy compositions, and reaction zones on both sides of the brazing alloy. The nickel-free bracket was a single piece with only slight variation in element concentration, but had a significantly rougher surface. After clinical use, no corrosive phenomena were detectable with the methods applied. Traces of intraoral wear at the contact areas between the bracket slot and the arch wire were verified. CONCLUSION: Electron probe microanalysis is a valuable tool for the characterization of element distribution and quantitative analysis for corrosion studies.

Effect of bonding material, etching time and silane on the bond strength of metallic orthodontic brackets to ceramic

The purpose of this study was to evaluate the bond strength of metallic orthodontic brackets to feldspathic ceramic with different etching times, bonding materials and with or without silane application. Cylinders of feldspathic ceramic were etched with 10% hydrofluoric acid for 20 or 60 s. For each etching time, half of the cylinders received two layers of silane. Metallic brackets were bonded to the cylinders using Transbond XT (3M Unitek) or Fuji Ortho LC (GC). Light-activation was carried out with total exposure time of 40 s using UltraLume 5. Shear bond strength testing was performed after 24 h storage. Data were submitted to three-way ANOVA and Tukey's test (α=0.05). The adhesive remnant index (ARI) was used to evaluate the amount of adhesive remaining on the ceramic surface at ×8 magnification. Specimens etched for 60 s had significantly higher bond strength compared with 20 s. The application of silane was efficient in increasing the shear bond strength between ceramic and both fixed materials. Transbond XT showed significantly higher (p<0.05) bond strength than Fuji Orth LC. There wasa predominance of ARI score 0 (clean ceramic failure surface) for all groups, with an increase in scores 1, 2 and 3 (adhesive material increasingly present on ceramic failure aspect) for the 60-s etching time. In conclusion, 60-s etching time, silane and Transbond XT improved significantly the shear bond strength of brackets to ceramic.

O objetivo neste estudo foi avaliar a resistência de união de bráquetes a cerâmica feldspática com diferentes tempos de condicionamento ácido, materiais de união, com ou sem aplicação do silano. Cilindros de cerâmica feldspática foram condicionados com ácido fluorídrico 10% por 20 ou 60 s. Para cada tempo de condicionamento, metade dos cilindros recebeu duas camadas de silano. Bráquetes metálicos foram fixados aos cilindros utilizando Transbond XT (3M Unitek) ou Fuji Ortho LC (GC). A fotoativação foi realizada com tempo de exposição total de 40 s utilizando LED UltraLume 5. O ensaio de resistência ao cisalhamento foi realizado após 24 h de armazenagem. Os dados foram submetidos à Análise de Variância a três fatores e teste de Tukey (α=0,05). O Índice de Remanescente Adesivo (IRA) foi utilizado para avaliar a quantidade de adesivo remanescente na superfície cerâmica com magnificação de 8×. Os espécimes condicionados por 60 s apresentaram maior resistência de união comparado com 20 s. A aplicação do silano foi efetiva no aumento da resistência de união ao cisalhamento de bráquetes com a cerâmica para ambos os materiais. O Transbond XT mostrou resistência de união significativamente maior que Fuji Orth LC. O IRA mostrou predominância de escore 0 (ausência de resina na superfície cerâmica) para todos os grupos, com aumento de escores 1, 2 e 3 (aumento da presença de resina na superfície cerâmica) para o tempo de condicionamento de 60 s. Em conclusão, o tempo de condicionamento de 60 s, aplicação de silano e resina Transbond XT melhoraram significativamente a resistência de união ao cisalhamento de bráquetes a cerâmica feldspática.

Análise in vitro da estabilidade de cor e rugosidade superficial de braquetes ortodônticos cerâmicos / In vitro analysis of the color stability and surface roughness of ceramic orthodontic brackets

Este estudo objetivou analisar, in vitro, a estabilidade de cor e rugosidade superficial de braquetes cerâmicos após imersão em soluções corantes. Sete braquetes cerâmicos de incisivo central superior direito de quatro marcas comerciais foram testados: dois monocristalinos e dois policristalinos. Os braquetes foram imersos em quatro soluções corantes (café, vinho tinto, Coca-Cola e chá preto) e em saliva artificial separadamente nos seguintes tempos: T0 (mensuração inicial), T1, T2, T3 e T4 (24 horas, 7,14 e 21 dias respectivamente).Outros sete braquetes de cada marca comercial foram imersos nas mesmas soluções e em tempos iguais aos anteriores, porém com intervalos de escovação diários. As alterações de cor foram avaliadas por espectrofotômetro de reflectância e a rugosidade superficial por meio de um Rugosímetro. Os dados foram avaliados pela Análise de Perfis Multivariados, Análise de Variância (ANOVA), teste de comparação múltipla de médias e Teste t de Student. Com base nos resultados, houve alteração perceptível de cor em todos os braquetes cerâmicos após 21 dias de imersão nas soluções de café (ΔE do Allure = 7,61, Inspire Ice = 6,09, Radiance=6,69, Transcend=7,44), chá preto (ΔE do Allure = 6,24, Inspire Ice = 5,21, Radiance=6,51, Transcend=6,14) e vinho tinto (ΔE do Allure =6,49 , Inspire Ice = 4,76, Radiance=5,19, Transcend=5,64), porém a alteração não foi perceptível para a Coca-Cola e saliva artificial (ΔE<3,7). Os braquetes submetidos à escovação apresentaram médias de alteração de cor significativamente menores e não perceptíveis, exceto para o chá preto. Rugosidade: Média Ra do Allure =0,277, Inspire Ice =0,262, Radiance=0,177, Transcend=0,367. A rugosidade variou apenas com o tempo de imersão. Cocluiu-se que houve alteração de cor dos braquetes cerâmicos quando imersos nas soluções, porém, apenas com o café, chá preto e vinho tinto essa alteração foi perceptível. A estrutura monocristalina ou policristalina não influencia na forma de manchamento. A escovação diária reduziu de forma significante a alteração de cor a níveis não visíveis ao olho humano, exceto para a solução de chá preto. Sobre a rugosidade superficial dos braquetes cerâmicos, não houve variação significante entre as diferentes marcas, soluções e presença ou ausência de escovação, apenas o fator tempo de imersão foi capaz de promover alguma variação. O Radiance foi o braquete que apresentou menor rugosidade e o Transcend a maior média. O Inspire Ice e o Allure são semelhantes quanto à rugosidade superficial

This study aimed to analyze in vitro the color stability and surface roughness of ceramic brackets after immersion in dye solutions. Seven ceramic brackets, upper right central incisor of four commercial brands were tested: two monocrystalline and two polycrystalline. The brackets were immersed separately in four staining solutions (coffee, red wine, Coca-Cola and black tea) and in artificial saliva at following times: T0 (initial measurement), T1, T2, T3 and T4 (24 hours, 7.14 and 21 days respectively). Other seven brackets of each brand were immersed in the same solutions and at same times as previous, but with brushing daily. The changes in color were evaluated by reflectance spectrophotometer and the surface roughness by a surface roughness gauger. The data were evaluated by Multivariate Analysis Profiles, Analysis of Variance (ANOVA), Multiple Comparison Test of means and Test t Student. Based on the results, there was perceptible change of color in all ceramic brackets after 21 days of immersion in coffee solution (ΔE of Allure = 7.61, Inspire Ice = 6,09, Radiance=6,69, Transcend=7,44), black tea (ΔE of Allure = 6,24, Inspire Ice = 5,21, Radiance=6,51, Transcend=6,14) and red wine (ΔE do Allure =6,49 , Inspire Ice = 4,76, Radiance=5,19, Transcend=5,64), but the change was not perceptible to the Coca-Cola and artificial saliva (ΔE <3.7). The brackets that were submitted to brushing showed average color change significantly smaller and not visible, except for black tea. Roughness: Ra Average of Allure = 0.277, Inspire Ice = 0.262, Radiance = 0.177, Transcend = 0.367. The roughness changed with the immersion time. It was cocluded that there was a change in color of ceramic brackets when immersed in the solutions, but only with coffee, black tea and red wine that change was perceptible. The monocrystalline or polycrystalline structure doesn't affect in the form of staining. Daily brushing significantly reduced the color change to levels not visible to the human eye, except for the solution of black tea. About the surface roughness of the ceramic brackets, there was no significant variation between different brands, solutions and presence or absence of brushing, only the immersion time factor was able to provide some variation. Radiance was the bracket with the lowest roughness and the Transcend with the highest average Inspire Ice and Allure are similar in surface roughness

The comparison of the frictional force by the type and angle of orthodontic bracket and the coated or non-coated feature of archwire / 대한치과교정학회지

OBJECTIVE: The purpose of this study was to evaluate the difference in frictional resistance among metal, ceramic, self-ligation brackets and coated or non-coated Ni-Ti archwires at various bracket-archwire angulations during the sliding movement of an orthodontic archwire, using an orthodontic sliding simulation device. METHODS: Four types of bracket (Micro-arch Perpect Clear2 Clippy-C and Damon3 and 5 types of orthodontic archwire (0.014", 0.016", and 0.016" x 0.022" inch coated Ni-Ti, and 0.016" and 0.016" x 0.022" inch Ni-Ti) were used. Further, the bracket-archwire angles were set at 4 different angulations: 0degrees, 3degrees, 6degrees, and 9degrees. RESULTS: The frictions from all the experimental groups were found to be significantly increased in order of self-ligation brackets, Micro-arch and Perpect Clear2 (p < 0.001). The presence of a coat had no effect on the friction of the same sized archwires at 0degrees and 3degrees bracket-archwire angles (p < 0.001). Coated archwires had significantly higher frictions than the same sized non-coated archwires at 6degrees and 9degrees bracket-archwire angles (p < 0.001). The frictions increased significantly as the bracket-archwire angles were increased (p < 0.001). CONCLUSIONS: The use of self-ligation brackets will be beneficial in clinical situations where a low frictional force is required. Further, in cases where crowding is not severe, the use of coated archwires should not cause problems. However, more additional explanation is required considering the fact that the damage of coated archwire and exposure of the metal portion in case of binding and notching and the effects of saliva were not taken into account.

Comparison of finishing and polishing systems for residual resin removal after debonding

OBJECTIVE : The aim of this study was to evaluate (1) the effectiveness of one-step polishers on the surface morphology of enamel using scanning electron microscope (SEM) and compare their effects with conventional systems for residual adhesive removal; and (2) the time spent to remove resin remnants. MATERIAL AND METHODS: Metal brackets were bonded to the buccal surface of 80 freshly extracted human premolar teeth and received the same resin-removal methods to evaluate the time spent to remove resin remnants (n=10). The brackets were debonded and residual adhesive was removed using different systems. Fourty-five premolars, including the control group with intact enamel (n=5), were examined by SEM. RESULTS: 30-blade tungsten carbide burs were the least time-consuming procedure. The best system in SEM study was the PoGo micro-polishers followed by Super-Snap Rainbow system. CONCLUSIONS: The effect of polishing systems on residual resin removal was dependent on the characteristics of the instruments in each system.

Quantitative analysis of mutans streptococci adhesion to various orthodontic bracket materials in vivo / 대한치과교정학회지

OBJECTIVE: To estimate the effects of bracket material type on enamel decalcification during orthodontic treatment, this study analyzed the adhesion level of mutans streptococci (MS) to orthodontic bracket materials in vivo. METHODS: Three different types of orthodontic bracket materials were used: stainless steel, monocrystalline sapphire, and polycrystalline alumina. A balanced complete block design was used to exclude the effect of positional variation of bracket materials in the oral cavity. Three types of plastic individual trays were made and one subject placed the tray in the mouth for 12 hours. Then, the attached bacteria were isolated and incubated on a mitis salivarius media containing bacitracin for 48 hours. Finally, the number of colony forming units of MS was counted. The experiments were independently performed 5 times with each of the 3 trays, resulting in a total of 15 times. Mixed model ANOVA was used to compare the adhesion amount of MS. RESULTS: There was no difference in colony forming units among the bracket materials irrespective of jaw and tooth position. CONCLUSIONS: This study suggested that the result of quantitative analysis of MS adhesion to various orthodontic bracket materials in vivo may differ from that of the condition in vitro.

Remoção de braquetes cerâmicos com alicate de How associado à broca diamantada: avaliação da topografia do esmalte / Removal of ceramic brackets with How-type pliers in association with diamond drill: a topographic evaluation of the enamel

OBJETIVO: avaliar a topografia do esmalte dentário após a descolagem de braquetes cerâmicos Allure (GAC/Dentsply) através de dois diferentes métodos. METODOLOGIA: foram utilizados 20 incisivos inferiores permanentes bovinos divididos em dois grupos (n = 10). Em ambos os grupos foram feitas colagens de braquetes cerâmicos Allure utilizando-se Concise (3M Unitek) seguindo as recomendações do fabricante. Após a colagem, os espécimes foram mantidos em estufa, a 37ºC por 24 horas, para completa polimerização do compósito. Após isso foi realizada a remoção dos braquetes, sendo que no grupo A foi utilizado alicate de corte de amarrilho e no grupo B alicate tipo How em braquete previamente fragilizado com broca diamantada. Em ambos os grupos o remanescente de compósito foi removido com broca de carboneto de tungstênio. Após descolagem, os espécimes foram preparados para análise em microscopia eletrônica de varredura, para posterior análise da superfície do esmalte. RESULTADOS E CONCLUSÕES: os resultados mostraram maior quantidade de arranhões nos dentes do grupo A, esses resultados foram estatisticamente superiores ao grupo B com p < 0,05. Dessa maneira, verificou-se que o uso do alicate tipo How em braquete previamente fragilizado produziu menores arranhões à superfície de esmalte, indicando-o para uso clínico.

OBJECTIVE: to evaluate the topography of the tooth enamel after debonding Allure ceramic brackets using two different methods. METHODS: Twenty bovine permanent lower incisors were divided into two groups (n = 10). In groups A and B Allure ceramic brackets were bonded to the teeth using Concise composite according to manufacture's recommendations. After the bonding procedures, the samples were kept in stove at 37ºC for 24 hours for complete composite polymerization. Next, the brackets of group A were removed by using wire pliers, whereas the brackets of group B, which had been previously weakened with diamond drill, were debonded by using How-type pliers. In both groups the composite remnant was removed by using a tungsten carbide-tipped drill. Following the debonding procedures, the samples were prepared for scanning electronic microscopy so that their enamel surfaces could be analyzed. RESULTS AND COCLUSION: showing more scratch marks on the surfaces of the group A teeth were statistically superior to those found in group B (p < 0.05). Therefore, it was observed that the use of How-type pliers for debonding pre-weakened brackets caused less scratches on the enamel surface, which supports their clinical use.

Resistência à remoção de braquetes ortodônticos sob ação de diferentes cargas contínuas / Shear bond strength of orthodontic brackets using different static loading application

OBJETIVO: testar se existe alteração na resistência adesiva de dois cimentos utilizados na colagem de acessórios ortodônticos ao esmalte dentário bovino, sendo um de polimerização química (Concise ortodôntico) e outro fotopolimerizável (Transbond XT), após a aplicação de cargas contínuas. METODOLOGIA: foram utilizados para este estudo 80 dentes bovinos e 80 braquetes metálicos. O esmalte bovino foi condicionado com ácido fosfórico a 37 por cento por 1 minuto e depois lavado e seco. A aplicação dos adesivos, manipulação e aplicação dos dois cimentos foram feitas de acordo com as instruções dos fabricantes. Após 24 horas, todos os braquetes foram submetidos a cargas contínuas de 30g, 70g e 120g, menos o grupo controle, que não recebeu carga alguma. Os espécimes ficaram imersos em água filtrada por 28 dias dentro de uma estufa a 37ºC. Depois deste período, as amostras foram submetidas a testes de cisalhamento em uma Máquina de Ensaios Universal Kratos. Os resultados foram registrados e enviados para análise estatística. CONCLUSÕES: (1) o cimento Concise apresentou maior resistência à remoção que o cimento Transbond XT para todas as cargas utilizadas, (2) não houve diferença estatisticamente significante na resistência adesiva frente às três cargas utilizadas para os dois cimentos testados; (3) no momento da fratura, conforme ocorreu o aumento da carga, a porcentagem de fratura do esmalte diminuiu para o Concise, ao contrário do cimento Transbond XT, onde a porcentagem de fratura de esmalte se manteve constante com o aumento das cargas.

AIM: The purpose of this study was to test differences on bond strength between auto-cured (Concise) and light-cured (Transbond XT) cements after static loading and shear test. METHODS: Eighty bovine teeth and metallic orthodontic brackets (Morelli Ortodontia Braquete Edgewise/Rickets) were tested after static loads of 30, 70 and 120grs. Bovine enamel was conditioned with 37 percent phosphoric acid gel for one minute, rinsed and dried. Adhesives were applied and brackets were bonded according to manufacturer's instructions. Cement thickness was standardized with the use of a heavier Gilmore needle. After 24 hours, half of the specimens were submitted to the static loads of 30, 70 and 120grs. Control group remained unloaded. Then, specimens were immersed in distilled water for 28 days at 37ºC. Afterwards, orthodontic brackets were attached to a loop wire and submitted to a shear force (Máquina de Ensaios Kratos Universal Kratos) under a crosshead speed of 0.5mm/min and load cell of 500Kgf. A two-way ANOVA test (alpha = 0.05) was used to detect significant interactions between cements and static loads. CONCLUSIONS: (1) The Concise cement showed more statistically significant bond strength values than the Transbond XT cement for all static loads; (2) No statistically significant differences were observed regarding static loads for all cements tested and (3) Higher static loads provided less enamel fracture in the Concise group after shear test, whereas in the Transbond XT the rate of enamel fracture remained unchanged regardless of previous load applied.