Selamento dentinário imediato em restauração semidireta: relato de caso / Immediate dentin sealing in semi-direct restoration: case report

O selamento dentinário imediato é um procedimento essencial na Odontologia, que envolve a aplicação de agentes de selamento na interface entre a dentina e o material restaurador imediatamente após a remoção da cárie e do preparo da cavidade dentária. Este processo busca selar os túbulos dentinários expostos, proporcionando proteção à polpa dentária. O presente caso foi realizado em um paciente do sexo masculino, 56 anos que se queixou de desconforto no elemento dentário 17. Após avaliação clínica e radiográfica, foi constatado uma ampla restauração desadaptada na porção mesio - oclusal do referido dente, sendo que o elemento em questão não possui tratamento endodôntico. Após planejamento e assinatura do TCLE, os seguintes passos foram realizados: remoção da lesão cariosa do dente 17, seguido da realização do levantamento marginal mesial e a realização do selamento dentinário imediato. Moldagem com silicone de adição do dente em questão e do antagonista, assim como registro da mordida. Foi confeccionada uma restauração semidireta em resina composta sob o modelo de gesso obtido. A cimentação da restauração foi feita na consulta seguinte, cumprindo os requisitos fundamentais para restaurar forma, função e estética, resultando na melhoria da qualidade de vida do paciente(AU)

Immediate dentin sealing is an essential procedure in dentistry, involving the application of sealing agents at the interface between dentin and the restorative material immediately after caries removal and cavity preparation. This process aims to seal exposed dentinal tubules, providing protection to the dental pulp. The present case involved a 56-year-old male patient who complained of discomfort in tooth number 17. After clinical and radiographic evaluation, a wide, maladapted restoration in the mesio-occlusal portion of the tooth was identified, with no endodontic treatment in the affected element. Following planning and informed consent, the following steps were taken: removal of the carious lesion from tooth number 17, followed by the execution of mesial marginal elevation and immediate dentin sealing. Silicone addition molding of the affected tooth and antagonist, along with bite registration, was performed. A semi-direct restoration in composite resin was fabricated based on the obtained gypsum model. The restoration was cemented in the subsequent appointment, meeting the essential requirements to restore form, function, and aesthetics, resulting in an improvement in the patient's quality of life(AU)

Restauração indireta em resina composta: um relato de prontuário / Indirect resin composite restoration: a dental record report

Restaurações diretas em resina composta são amplamente utilizadas em odontologia para restaurar dentes posteriores. Todavia, quando há grande destruição coronária, onde a distância do istmo excede dois terços da distância intercuspídea, as restaurações indiretas em resina composta são indicadas. O presente estudo teve como objetivo relatar a análise de um prontuário de um paciente que recebeu uma restauração indireta em resina composta em dente posterior amplamente destruído. Através da análise de prontuários de pacientes atendidos nas disciplinas de Estágios Supervisionados do Curso de Odontologia da FSG Centro Universitário no ano de 2023, foi selecionado um prontuário de um paciente que compareceu a clínica odontológica da FSG com uma restauração em amálgama fraturada com reparo em resina composta que apresentou sintomatologia dolorosa. O procedimento diagnóstico ocorreu através de exame clínico e radiográfico, que constatou a indicação de substituição da restauração insatisfatória e realização de uma restauração indireta em resina composta. Os resultados estéticos e funcionais apresentados demostraram a viabilidade da técnica restauradora indireta em resina composta para reabilitar dentes posteriores com ampla destruição coronária(AU)

Direct composite resin restoration are widely used in dentistry to restore posterior teeth. However, when there is large coronary destruction, that the distance from the isthmus exceeds two- thirds of the intercuspal distance, indirect composite resin restorations are indicated. This study aimed to report the analysis of a dental record of a patient who received an indirect restoration in composite resin in a badly destroyed posterior tooth. Through the analysis of dental records of patients seen in the disciplines of Supervised Internship of the Dentistry Course at FSG Centro Universitário in the year 2023, the dental record of a patient who attended the FSG dental clinic with fractured amalgam restoration with composite resin repair was selected who had painful symptoms. The diagnostic procedure took place through clinical and radiographic examination, which revealed the indication of replacing the unsatisfactory restoration and carrying out an indirect restoration in composite resin.The aesthetic and functional results presented demonstrated the viability of the indirect composite resin restoration technique for rehabilitating posterior teeth with extensive coronal destruction(AU)

Restauração em resina composta semidireta em dente posterior: relato de caso / Semi-direct composite restoration in posterior toth: a case report

A escolha da técnica restauradora desempenha papel fundamental na eficácia e duração de um tratamento reabilitador. O objetivo deste relato de caso foi descrever a utilização da técnica semidireta para a confecção de uma restauração em resina composta em um primeiro molar inferior. A paciente apresentava uma restauração insatisfatória no dente 36, que necessitava ser substituída devido à infiltração por cárie. Optou-se pela técnica semidireta devido à amplitude da cavidade, que envolvia estruturas de suporte, e pela combinação das vantagens das abordagens direta e indireta. O procedimento envolveu a remoção de tecido cariado, a aplicação de hidróxido de cálcio pasta, seguida da aplicação de uma fina camada de ionômero de vidro e, posteriormente, resina fluída para realizar o selamento dentinário. O preparo foi realizado seguindo os princípios necessários. O elemento em questão foi moldado com silicone de adição e o arco antagonista, com alginato. Ambos modelos foram vertidos com silicone para modelos semirrígidos e montados em oclusor de peças de brinquedo. A restauração semidireta foi confeccionada em resina composta Filtek Z350 XT, respeitando a anatomia do dente 36. Pigmentos foram utilizados para aprimorar detalhes estéticos. Após acabamento e polimento, a peça foi condicionada e cimentada com cimento dual Relyx Ultimate. Pode-se concluir que a abordagem restauradora por meio da técnica semidireta construída em modelo semirrígido é uma opção terapêutica conservadora e vantajosa para dentes com extensa destruição coronária. Essa técnica possibilita a restauração de forma eficaz, garantindo tanto a estética quanto a função adequada do dente afetado(AU)

The choice of restorative technique plays a fundamental role in the effectiveness and duration of rehabilitation treatment. The objective of this case report was to describe the use of the semi-direct technique to create a composite resin restoration in a lower first molar. The patient had an unsatisfactory restoration on tooth 36, which needed to be replaced due to cavity infiltration. The semi-direct technique was chosen due to the amplitude of the cavity, which involved support structures, and the combination of advantages of the direct and indirect approaches. The procedure involved the removal of carious tissue, and the application of calcium hydroxide paste, followed by the application of a thin layer of glass ionomer and, subsequently, fluid resin to seal the dentin. The preparation was carried out following the necessary principles. The element in question was molded with addition silicone and the antagonist arch was molded with alginate. Both models were poured with silicone for semi-rigid models and mounted on toy parts occluders. The semi-direct restoration was made in Filtek Z350 XT composite resin, respecting the anatomy of tooth 36. Pigments were used to improve aesthetic details. After finishing and polishing, the piece was conditioned and cemented with Relyx Ultimate dual cement. It can be concluded that the restorative approach using the semi-direct technique built on a semi-rigid model is a conservative and advantageous therapeutic option for teeth with extensive coronal destruction. This technique allows for effective restoration, ensuring both the aesthetics and adequate function of the affected tooth(AU)

Reanatomização estética dos dentes anteriores com resina composta: relato de caso / Reanatomización estética de dientes anteriores com resina compuesta: reporte de caso / Aesthetic reanatomization of front teeths with composite resin: case report

Introdução: A alta busca por tratamentos estéticos levou a indústria odontológica a aprimorar suas técnicas e desenvolver materiais com novas características que possibilitam a mimetização da estrutura dental, associando alta qualidade estética à saúde. Para isso, é necessário uma anamnese detalhada e exame físico intra e extrabucal, análise morfológica dos dentes e da face, para que a reabilitação proposta seja adequada. Objetivo: O objetivo deste estudo é descrever um caso clínico de reanatomização dos elementos dentais anteriores superiores, por meio de restaurações diretas em resina composta, restabelecendo a estética e função da paciente. Relato de caso: Paciente do sexo feminino, 19 anos, procurou a Clínica Escola da Faculdade de Odontologia do Recife -FOR relatando insatisfação com seu sorriso e declarou não estar disposta a se submeter a um tratamento ortodôntico. Ao realizar o exame clínico, observou-se que havia desalinhamento dos elementos dentários ântero-superiores. Após a realização do enceramento diagnóstico e validação da mesma através do mockupcom resina bisacrílica, optou-se por realizar a reanatomização estética com resina composta nanohíbrida, de forma conservadora, ou seja, sem desgastar os dentes em questão. Conclusão: As etapas do planejamento foram fundamentais para maior previsibilidade e obtenção do excelente resultado. Os materiais e técnicas selecionados para realização dos procedimentos aliaram características de resistência e estética, visando maior longevidade (AU).

Introduction: The high demand for aesthetic treatments has led the dental industry to improve its techniques and develop materials with new characteristics that allow mimicking the tooth structure, associating high aesthetic quality with health. This requires a detailed anamnesis,intra-and extraoral physical examination, and morphological analysis of the teeth and faceto allow an adequate proposed rehabilitation. Objective:The objective of this study is to describe a clinical case of reshaping of upper anterior teeth, by direct composite resin restorations, reestablishing the patient's aesthetics and function. Case report:Female patient, 19 years old, sought the Clínica Escola da Faculdade de Odontologia do Recife -FOR, reporting dissatisfaction with her smile and declared that she was unwilling to undergo orthodontic treatment. Clinical examinationrevealed misalignment of the upper anteriorteeth. After diagnostic waxing and validation by mockup with bis-acryl resin, it was decided to perform the aesthetic reshaping with nanohybrid composite resin in a conservative manner, i.e., without tooth wearing . Conclusion:The planning stages were fundamental for greater predictability and obtaining excellent results. The materials and techniques selected for the procedurescombined resistance and aesthetic characteristics, aiming at greater longevity (AU).

Introducción:La gran demanda para tratamientos estéticos ha llevado a la industria dental a mejorarsus técnicas y desarrollar materiales con nuevas características que permitan mimetizar la estructura dental, combinando una alta calidad estética con la salud. Para que esto ocurra, es necesario realizer una anamnesis detallada y un examen físicointra y extraoral, así como un análisis morfológico de los dientes y de la cara, para que la rehabilitación propuesta sea da adecuada. Objetivo:El objetivo de este studio es describir un caso clínico de reanatomización de los elementos dentales de resinacompuesta, restabeleciendo la estética y función de la paciente. Informe de caso:Paciente del sexo feminine, 19 años de edad, que acudió a la Clínica Escuela de La Facultad de Odontología de Recife ­FOR menifestando insatisfaccíon con su sonrisa y declarando no estar dispuesta a someterse a tratamiento de ortodoncia. En el examen clínico se observódesalineación de los elementos dentarios anterosuperiores. Tras realizar un encerado diagnóstico y validarlo con un mock-up de resina bisacrílica, se optó porrealizer una reanatomización estética con resina compuesta nanohíbrida de forma conservadora, es decir, sin desgastarlos dientes implicados. Conclusión:Las etapas de planificacíon han sido fundamentales para una mayor previsibilidad y la obtención de excelentes resultados. Los materiales y técnicas seleccionados para la realización de los procedimentos combinaron características de resistencia y estética, buscando una mayor longevidad (AU).

Bisphenol A released and ultrastructural changes in dental composite resins

Dental composite resins may release bisphenol-A or similar molecules affecting patient health and the environment. This study measured bisphenol-A release from three commonly used in patients composite resins (Filtek™ Z350 XT, Filtek™ P60, Filtek™ Bulk Fill) immersed in three liquid mediums (artificial saliva, 0.001 M lactic acid and 15% ethanol) and assessed the changes in the surface micromorphology.The released BPA was measured by HPLC at basal time (t=0), 1 h, 1 d, 7 d and 30 d. Topographic analysis of specimens was performed by scanning electron microscopy (SEM). The data were analyzed using one-way ANOVA and Tukey post-hoc test (P < 0.05). BPA in solution increased significantly in the three DCRs immersed in 0.001 M lactic acid at all times. SEM micrographs of the specimen in 0.001 M lactic acid disclosed more structural defects than others. The surface of the three composite resins was morphologically affected by their immersion in all solutions. SEM evidenced that the dental materials underwent erosion and cracks with filler particles protruding from the surface. The morphological changes in tested dental materials produced by exposure to these solutions are potentially dangerous to patients by causing caries, infections, and partial loss of dental material.

Mathematical-Physical description of the oxygen-inhibited layer (OIL) in nanofilled dental polymers / Descripción físico-matemática de la capa inhibida por oxígeno en polímeros dentales nano rellenados

Abstract This research evaluates the presence of the oxygen-inhibited layer (OIL) on the top surface of a photopolymerized dental composite resin protected with a glycerin layer. This evaluation was conducted using physical and mathematical methods. Polymerized discs were fabricated to evaluate Vickers microhardness (VHN), and pre-and post-polymerized samples were used for the calculation of C-O/C-H ratios through Fourier Transform Infrared Spectroscopy (FTIR) (n=10), using two types of glycerin, one for medical use (MG) and another for dental use (DG). Surface hardness decreased from MG to DG to CO, and the increase in C-O/C-H ratios decreased in the same order (p<0.05). Samples protected with medical and dental glycerin layers are harder and exhibit lower C-O/C-H bond ratios than the control group.

Resumen La presente investigación evalúa la presencia de la capa inhibida por oxígeno OIL en la última superficie fotocurada de una resina compuesta de uso odontológica que fue protegida con una capa de glicerina. Esta evaluación se hizo a partir de métodos físicos y matemáticos. Se fabricaron discos polimerizados para evaluar la microdureza Vickers (VHN) y pre y post polimerizados para el cálculo de tasas C-O/C-H por medio de Espectroscopía Infrarroja Transformada de Fourier (FTIR) (n=10) usando dos tipos de glicerina, una de uso médico (MG) y otra de uso dental (DG). La dureza superficial disminuyó de MG a DG a CO y el aumento de tasas C-O/C-H disminuyó en ese mismo orden (p<0,05). Las muestras protegidas con capas de glicerina médica y odontológica son más duras y presentan menos cantidad tasas de enlaces C-O/C-H que el grupo control.

Effect of different decontamination agents on the bond strength of CAD/CAM blocks and repair composite materials / Efecto de diferentes agentes descontaminantes sobre la resistencia de unión de bloques CAD/CAM y resinas compuestas

Abstract The purpose of this study was to examine the effect of different decontamination agents on the bond strength of saliva-contaminated CAD/CAM blocks and repair composite materials. Two hunderd eighty 3-mm-thick specimens were prepared from four different CAD/CAM materials: Katana Zirconia UTML disc, IPS e.max CAD block, Shofu block, and Vita Enamic block. Each material was divided into seven different subgroups (N=70). Group 1 had a clean surface. The other groups were comprised of the samples, which were contaminated with human saliva: group 2: negative control (non-cleaned); group 3: cleaned with water spray; group 4: cleaned with 70% ethanol; group 5: cleaned with Ivoclean; group 6: cleaned with Katana Cleaner; and group 7: cleaned with phosphoric acid. After the decontamination protocols, the resin composite cylinders were bonded to the CAD/CAM surfaces with a thin layer of dual-cured resin cement. The samples were stored for 24 hours at 37°C in distilled water. Then, they were subjected to a shear bond strength test (SBS). The values were recorded, and fracture types were evaluated using a microscope. Data were analyzed using two-way ANOVA and Tukey's post-hoc test. Generally, all decontaminating agents improved the SBS of composites to Katana Zirconia UTML, IPS e.max, and Vita Enamic materials (p<0.05). However, for Shofu materials, group 6 samples exhibited significantly higher bond strength values as compared with group 2 samples (p=0.026). The highest SBS values were seen in the phosphoric acid-treated group in Katana zirconia materials (26.45 ± 9.38 MPa), whereas the lowest values were seen in group 2 samples in Shofu materials (13.17±3.40 MPa). Each decontaminant agent improved the bond strength of composites to the contaminated CAD/CAM materials. If saliva is not cleaned before adhesive procedure, SBS values may decrease. All decontamination agents can be used safely on zirconia, lithium-disilicate glass-ceramic, hybrid ceramic, and polymer-infiltrated ceramic surfaces.

Resumen El propósito de este estudio fue examinar el efecto de diferentes agentes descontaminantes sobre la fuerza de unión de bloques CAD/CAM contaminados con saliva y materiales compuestos de reparación. Se prepararon doscientas ochenta muestras de 3 mm de espesor a partir de cuatro materiales CAD/CAM diferentes: disco Katana Zirconia UTML, bloque IPS e.max CAD, bloque Shofu y bloque Vita Enamic. Cada material se dividió en siete subgrupos diferentes (N=70). El grupo 1 tenía una superficie limpia. Los otros grupos estaban compuestos por muestras que estaban contaminadas con saliva humana: grupo 2: control negativo (no limpio); grupo 3: limpiado con agua pulverizada; grupo 4: limpiado con etanol al 70%; grupo 5: limpiado con Ivoclean; grupo 6: limpiado con Katana Cleaner; y grupo 7: limpiado con ácido fosfórico. Después de los protocolos de descontaminación, los cilindros de composite de resina se adhirieron a las superficies CAD/CAM con una fina capa de cemento de resina de curado dual. Las muestras se almacenaron durante 24 horas a 37°C en agua destilada. Luego, fueron sometidos a una prueba de resistencia al corte (SBS). Se registraron los valores y se evaluaron los tipos de fracturas utilizando un microscopio. Los datos se analizaron mediante ANOVA de dos factores y la prueba post-hoc de Tukey. En general, todos los agentes descontaminantes mejoraron el SBS de los composites con los materiales Katana Zirconia UTML, IPS e.max y Vita Enamic (p<0,05). Sin embargo, para los materiales Shofu, las muestras del grupo 6 exhibieron valores de fuerza de unión significativamente más altos en comparación con las muestras del grupo 2 (p=0,026). Los valores más altos de SBS se observaron en el grupo tratado con ácido fosfórico en materiales de circonio Katana (26,45 ± 9,38 MPa), mientras que los valores más bajos se observaron en las muestras del grupo 2 en materiales Shofu (13,17 ± 3,40 MPa). Cada agente descontaminante mejoró la fuerza de unión de los composites a los materiales CAD/CAM contaminados. Si no se limpia la saliva antes del procedimiento adhesivo, los valores de SBS pueden disminuir. Todos los agentes descontaminantes se pueden utilizar de forma segura en superficies de circonio, cerámica de vidrio de disilicato de litio, cerámica híbrida y cerámica con infiltraciones de polímeros.

Color variation of composite resins in relation to the Vita Classical shade guide: colorimetric analysis

Aim: The aim of this study was to verify the color variation between different composite resins and the Vita Classical Shade Guide. Methods: Two-millimeter thickness samples were made (n = 6) from eight commercial brands of composite resin (shade A2): Charisma (Kulzer), Forma (Ultradent), Harmonize (Kerr), Luna (SDI), Opallis (FGM), Oppus Bulk Fill (FGM), Vittra (FGM) and Filtek Z250 XT (3M ESPE). Specimens were stored in distilled water for 7 days and then polished. Color measurements of samples and A2 shade of the Vita Classical Shade Guide were performed using the Vita Easy Shade Advance 4.0 spectrophotometer on a black background. Color variations were calculated using the CIEDE2000 formula, considering values ≥0.81 being noticeable by the human eye and ≥1.77 being clinically unacceptable. Results were statistically analyzed with a 5% significance level. Results: Color variation (ΔE) of composite (E1 ) compared to the Vita Classical Shade Guide (E0 ) was greater than clinically acceptable for all the materials evaluated in this study. Forma (ΔE=2.08 ± sd=0.47) and Filtek Z250 XT (2.50 ± 0.20) had the smallest amount of color variation values found in the results. Harmonize (3.32 ± 0.63) presented values similar to Filtek Z250 XT, but it was worse than Forma. Vittra (3.51 ± 0.28), Charisma (3.80 ± 0.20), Opallis (4.24 ± 0.30) and Luna (5.67 ± 0.20) did not differ among each other and presented higher color variation than Forma, Filtek Z350XT and Harmonize. Oppus Bulk Fill (13.94 ± 1.12) was the composite with the greatest color variation. Conclusions: The findings in this study show that attention should be taken when using the Vita Color Shade Guide for composite shade selection

Effect of Water and Chlorhexidine with Different Pressures of Oral Irrigation Device on the Surface Roughness and Topography of Giomer

Abstract Objective: To evaluate the effect of different pressures of an oral irrigation device (OID) and the irrigation solution type on the surface roughness of the giomer restorative material. Material and Methods: In this in vitro study, disk-shaped giomer samples were fabricated and assigned to 5 groups (n=23): Group 1, storage in distilled water (control); Group 2, OID #7 pressure/ water; Group 3, OID #10 pressure/ water; Group 4, OID #7 pressure/ 0.05% CHX; Group 5, OID #10 pressure/ 0.05% CHX. The samples' treatment simulated a one-year application of OID. Surface roughness (Ra) and topography of the giomer were evaluated using profilometry and scanning electron microscopy. The data were analyzed with Paired t-test, Tukey, and ANOVA tests (α=0.05). Results: The Ra of the samples increased significantly after treatment with OID (p<0.001). The roughness increase in groups with a pressure of 10 was higher than those with a pressure of 7 (p<0.001). The effect of pressure on surface changes was significant (p<0.001). However, the solution type and the cumulative effect of these two factors were insignificant (p=0.08 and p=0.43, respectively). Conclusion: Oral irrigation device with both solutions significantly increased the surface roughness and topographic changes of the giomer. The severity of these changes was related to the device's pressure.

Effect of composite radiopacity and margin location of the restoration on the diagnosis of secondary caries

Abstract This research aimed to evaluate the effect of the radiopacity of a Bulk-Fill composite (X-TraFil, VOCO, Germany) and a Conventional composite (P60, 3M ESPE, USA) and assessment of the margin location in the enamel and dentin on the diagnosis of secondary caries. 76 intact premolars with MOD preparation were divided into two equal groups and filled with the conventional and bulk-fill composite. Four regions were considered to simulate carious lesions (two regions in enamel and two regions in dentin). In each group, half of the regions in the dentin and half in the enamel were randomly selected for secondary caries simulation and filled with a wax-plaster combination while the remaining regions stayed intact. Bitewing imaging was done using the PSP digital sensor. Five examiners reviewed the images, and lesions were recorded. Caries diagnosis indicators and paired-sample t-test were used for statistical analysis. The reproducibility and accuracy of the examiners' responses were evaluated using the kappa and agreement coefficient (α=0.05). The sensitivity, specificity, and accuracy of diagnosing secondary carious lesions in enamel were significantly better under conventional than bulk-fill composite. Similarly, the sensitivity and accuracy of diagnosing secondary caries in dentin were significantly higher under conventional composite than bulk-fill composite (p<0.05). No significant differences were found in the agreement and kappa coefficient between conventional and bulk-fill composites in the enamel and dentin (p>0.05). The diagnostic accuracy of carious lesions was higher under conventional composite than bulk-fill composite. However, the location of the secondary was ineffective in caries diagnosis.

Resumo Essa pesquisa teve como objetivo avaliar o efeito da radiopacidade de resina composta Bulk-Fill (X-TraFil, VOCO, Alemanha) e de resina composta convencional (P60, 3M ESPE, EUA) e a avaliação da localização da margem no esmalte e na dentina no diagnóstico de cárie secundária. 76 pré-molares intactos com preparo MOD foram divididos em dois grupos iguais e restaurados de acordo com o grupo experimental. Quatro regiões foram consideradas para simular lesões de cárie (duas regiões no esmalte e duas regiões na dentina). Em cada grupo, metade das regiões na dentina e metade no esmalte foram selecionadas aleatoriamente para a simulação de cárie secundária e preenchidas com uma combinação de cera e gesso, enquanto as regiões restantes permaneceram intactas. As imagens de bitewing foram feitas usando o sensor digital PSP. Cinco examinadores analisaram as imagens, e as lesões foram registradas. Os indicadores de diagnóstico de cárie e o teste t de amostra pareada foram usados para análise estatística. A reprodutibilidade e a precisão das respostas dos examinadores foram avaliadas usando o kappa e o coeficiente de concordância (α=0,05). A sensibilidade, a especificidade e a precisão do diagnóstico de lesões cariosas secundárias no esmalte foram significativamente melhores com a resina composta convencional do que com a resina composta bulk-fill. Da mesma forma, a sensibilidade e a precisão do diagnóstico de cáries secundárias na dentina foram significativamente maiores com a resina convencional do que com a resina bulk-fill (p<0,05). Não foram encontradas diferenças significativas na concordância e no coeficiente kappa entre as resinas convencionais e bulk-fill no esmalte e na dentina (p>0,05). A precisão do diagnóstico de lesões cariosas foi maior com a resina composta convencional do que com a resina composta bulk-fill. Entretanto, a localização do secundário foi ineficaz no diagnóstico de cárie.

Color matching and color recovery in large composite restorations using single-shade or universal composites

Abstract This study assessed the color-matching ability and color recovery of unprepared teeth when using single-shade composites and a universal composite in large restorations. Buccal and palatine surface colors of molars were measured with a spectrophotometer (CIELAB) before preparing round cavities (6 mm in diameter, 2 mm in depth). The cavities were randomly filled with a single-shade composite (Omnichroma, Diamond One, or Vittra APS Unique) or a universal composite (Filtek Universal). Color measurements of the restored cavities were taken, and overall color differences (ΔEab and ΔE00) and differences in the whitening index for dentistry (ΔWID) from baseline were calculated. Additionally, visual assessments of a color match to the surrounding enamel were performed by forty evaluators (laypersons and undergraduate students of dentistry) in a viewing booth under illuminant D65, with rating scores from 0 (no color mismatch) to 4 (not acceptable). Data were analyzed using RM or one-way ANOVA (α = 0.05). Results showed that the restorations generally exhibited whiter colors (WID ranged from 27.9 to 41.3) than the unprepared teeth (WID ranged from 15.9 to 19.3). The composite Filtek Universal demonstrated the lowest color discrepancy (ΔWID = 8.6; ΔE00 = 10.8; and ΔE00 = 6.2), and no significant differences were observed among the evaluated single-shade composites. Furthermore, all composites showed similar and adequate color matches to the surrounding enamel. However, it is important to note that despite their ability to match the surrounding enamel reasonably, none of the composites evaluated in large restorations fully recovered the color observed in unprepared teeth.

Resumo Este estudo avaliou a habilidade de combinação de cores e recuperação de cor de dentes não preparados ao utilizar resinas compostas de única tonalidade e uma resina composta universal em grandes restaurações. As cores das superfícies bucais e palatinas de molares foram medidas com um espectrofotômetro (CIELAB) antes de preparar cavidades esféricas (6 mm de diâmetro, 2 mm de profundidade). As cavidades foram preenchidas aleatoriamente com uma resina composta de única tonalidade (Omnichroma, Diamond One ou Vittra APS Unique) ou com uma resina composta universal (Filtek Universal). Foram realizadas medições das cores das cavidades restauradas e calculadas as diferenças de cor globais (ΔEab and ΔE00)) e as diferenças no índice de clareamento para odontologia (ΔWID) em relação à cor inicial. Além disso, foram realizadas avaliações visuais da correspondência de cor com o esmalte circundante por quarenta avaliadores (leigos e estudantes de odontologia) em uma cabine de visualização sob iluminante D65, com pontuações de 0 (nenhuma discrepância de cor) a 4 (não aceitável). Os dados foram analisados usando RM ou ANOVA unidirecional (α = 0,05). Os resultados mostraram que as restaurações geralmente apresentavam cores mais brancas (WID variou de 27,9 a 41,3) do que os dentes não preparados (WID variou de 15,9 a 19,3). A resina composta Filtek Universal demonstrou a menor discrepância de cor (ΔWID = 8,6; ΔE00 = 10,8; and ΔE00 = 6,2), e não foram observadas diferenças significativas entre as resinas compostas de única tonalidade avaliadas. Além disso, todas as resinas compostas apresentaram correspondência de cor similar e adequada com o esmalte circundante. No entanto, é importante observar que, apesar de sua capacidade de corresponder razoavelmente com o esmalte circundante, nenhuma das resinas compostas avaliadas em grandes restaurações recuperou completamente a cor observada nos dentes não preparados.

Niobium oxyhydroxide as a bioactive agent and reinforcement to a high-viscosity bulk-fill resin composite

Abstract Objective The present in vitro study incorporated niobium oxyhydroxide fillers into an experimental high-viscosity bulk-fill resin composite to improve its mechanical performance and provide it a bioactive potential. Methodology Scanning electron microscopy synthesized and characterized 0.5% niobium oxyhydroxide fillers, demonstrating a homogeneous morphology that represented a reinforcement for the feature. Fillers were weighed, gradually added to the experimental resin composite, and homogenized for one minute, forming three groups: BF (experimental high-viscosity bulk-fill resin composite; control), BF0.5 (experimental high-viscosity bulk-fill resin composite modified with 0.5% niobium oxyhydroxide fillers), and BFC (commercial bulk-fill resin composite Beautifil Bulk U, Shofu; positive control). In total, 10 specimens/groups (8 × 2 × 2 mm) underwent flexural strength (FS) tests in a universal testing machine (Instron) (500N). Resin composites were also assessed for Knoop hardness (KH), depth of cure (DoC), degree of conversion (DC), elastic modulus (E), and degree of color change (ΔE). The bioactive potential of the developed resin composite was evaluated after immersing the specimens into a simulated body fluid in vitro solution and assessing them using a Fourier-transformed infrared spectroscope with an attenuated total reflectance accessory. One-way ANOVA, followed by the Tukey's test (p<0.05), determined FS, DC, KH, and ΔE. For DoC, ANOVA was performed, which demonstrated no significant difference between groups (p<0.05). Conclusions The high-viscosity bulk-fill resin composite with 0.5% niobium oxyhydroxide fillers showed promising outcomes as reinforcement agents and performed well for bioactive potential, although less predictable than the commercial resin composite with Giomer technology.

Color and surface roughness alterations of bulk-fill resin composites submitted to simulated toothbrushing with whitening dentifrices

Aim: To evaluate the surface roughness and color stability of bulk-fill resin composites after simulated toothbrushing with whitening dentifrices. The radioactive/relative dentin abrasion (RDA) and radioactive/relative enamel abrasion (REA) of dentifrices were also assessed. Methods: Specimens (n=10) of Tetric N Ceram Bulk Fill (TNCB), Filtek One Bulk Fill (FOB) resin composites, and Z100(Control) were prepared using a cylindrical Teflon matrix. Surface roughness (Ra, µm) was assessed by a roughness meter and the color evaluations (ΔEab , ΔE00 , WID ) were performed using a digital spectrophotometer based on the CIELAB system. Three measurements were performed per sample, before and after simulated toothbrushing with 3D Oral-B White Perfection (3DW) and Black is White (BW) dentifrices. The abrasivity (REA and RDA values) of the used dentifrices was also determined by the Hefferren abrasivity test. Results: The Ra values increased significantly in all resin composites after 3DW and BW toothbrushing. The acceptable threshold color varied among resin composites, and TNCB and Z100 presented the highest ΔEab and ΔE00 for BW dentifrice. The 3DW dentifrice was significantly more abrasive than BW dentifrice on enamel and dentin. Conclusions: simulated toothbrushing with tested whitening dentifrices increased the surface roughness at acceptable levels. The Tetric N Ceram Bulk-fill and Z100 composite showed the highest color alteration in BW. 3D White Perfection dentifrice was more abrasive on dentin and enamel than Black is White.

Assessment of bulk-fill of resins microhardness longitudinal

Aim: This study aimed to assess the polymerization effectiveness of bulk-fill composite resins in longitudinal microhardness. Methods: Blocks of bulk-fill composite resin with thicknesses of 6 mm were analyzed with Vickers microhardness. The resin blocks were divided into two groups (n=6): resin AURA and OPUS. The microhardness test was performed before (base and top) and after (longitudinal microhardness) sectioning the blocks at distances of 2 mm, 4 mm, and 6 mm from the top of the block. The mean microhardness values were tabulated and subjected to ANOVA followed by Tukey's test (p<0.05). Results: The OPUS bulk-fill resin samples presented microhardness means of 55.9 kgf/mm2, 53.7 kgf/mm2, and 49.3 kgf/mm2, the AURA bulk-fill resin samples presented microhardness means of 57,02 kgf/mm2, 55,86 kgf/mm2 e 51,77 kgf/mm2 for the distances of 2 mm, 4 mm, and 6 mm, respectively. Tukey's statistical test showed a significant difference in microhardness values at different distances of 2 mm, 4 mm, and 6 mm (p<0.001) for each resin. Although there was a statistically significant difference within and between the groups assessed, all samples showed polymerization effectiveness when comparing the top and base of the block. Conclusion: Polymerization was effective in different thicknesses (2 mm, 4 mm, and 6 mm) in both resins studied. The microhardness ratio was adequate when comparing the base and top

Effect of Toothpaste Fluoride Concentration on Color Stability of Resin Composites: An In Vitro Study

ABSTRACT Objective: To investigate the effects of two different dentifrice fluoride concentrations on the color stability of the composite. Material and Methods: Twenty-seven specimens (2×4×5 mm) each of microfilled (Gradia, GC, Japan) and nanohybrid (Grandio, VOCO, Germany) composites were prepared. The specimens were randomly divided into six groups (control, Fluoflor caries protection toothpaste with 1450ppm Fluoride (EXW, France), and Fluoflor kids toothpaste with 500ppm Fluoride (EXW, France) (n = 9). The specimens were immersed in a mixture of artificial saliva and toothpaste in a ratio of 1:3 and applied for 60 seconds every 12 hours for 42 days. The control samples were incubated in artificial saliva at 37°C. Primary and secondary color measurements were performed using color parameters (L∗a∗b) with a spectrophotoshade (MHT Optic Research AG, Niederhasli, Switzerland). Data were analyzed using a two-way analysis of variance at a significance level of 0.05. Results: According to the two-way ANOVA analysis, there was no significant difference in color change between the composites and no difference in the level of discoloration between different fluoride concentrations(p>0.05). Also, None of the dentifrices caused clinically significant color changes(∆E˂3.3). Conclusion: No clinically unacceptable color changes were observed in the microfilled and nanofilled composites with different concentrations of fluoride toothpaste.

Reliability of the color measurement of resin composites using images obtained using a stereoscopic loupe

Abstract This study assessed the reliability of a color measurement method using images obtained from a charge-coupled device (CCD) camera and a stereoscopic loupe. Disc-shaped specimens were created using the composite Filtek Z350 XT (shades DA1, DA2, DA3, and DA4) (n = 3). CIELAB color coordinates of the specimens were measured using the spectrophotometer SP60 over white and black backgrounds. Images of the same specimens were taken using a CCD camera attached to a stereoscopic loupe. The color of the image was measured (red-green-blue [RGB]) using an image processing software and converted to CIELAB coordinates. For each color coordinate, data from images were adjusted using linear regressions predicting those values from SP60. The whiteness index for dentistry (WID) and translucency parameter (TP00) of the specimens as well as the color differences (ΔE00) among pairwise shades were calculated. Data were analyzed via repeated-measures analysis of variance and Tukey's post hoc test (α = 0.05). Images obtained using the loupe tended to be darker and redder than the actual color. Data adjustment resulted in similar WID, ΔE00, and TP00 values to those observed for the spectrophotometer. Differences were observed only for the WID of shade DA3 and ΔE00 for comparing DA1 and DA3 over the black background. However, these differences were not clinically relevant. The use of adjusted data from images taken using a stereoscopic loupe is considered a feasible method for color measurement.

Short curing time bulk fill composite systems: volumetric shrinkage, degree of conversion and Vickers hardness

Abstract This study aimed to evaluate volumetric polymerization shrinkage, degree of conversion and Vickers hardness of four bulk-fill resin composites light-activated with their dedicated light curing units (LCUs). Four groups were evaluated, according to the type of composite and curing mode: Tetric EvoCeram Bulk-fill (TEBO) and Tetric EvoFlow Bulk-fill (TEBF) were light-activated with Bluephase Style 20i (20s, in high-mode), while Tetric Powerfill (TEPO) and Tetric Powerflow (TEPF) were light-activated with Bluephase PowerCure (3s). Volumetric polymerization shrinkage test (n = 6) was performed in standardized box-shaped class-I cavities of extracted third molars (4 x 4 x 4 mm). Teeth were scanned before and after resin composite application by micro-computed tomography, and acquired data were evaluated with Amira software. Degree of conversion (n = 5) was evaluated at the top and bottom surfaces of composite cylindric samples (4 mm diameter, 4 mm thickness) using an FT-IR spectrometer (spectra between 1,500 and 1,800 cm-1, 40 scans at a resolution of 4 cm-1). Three Vickers indentations (50 g / 15 s), spaced 500 μm apart, were performed on the top and bottom composite surfaces and averaged. One-way ANOVA was used for data evaluation. TEPF showed the lowest volumetric polymerization shrinkage (p < 0.05), while the other composites were not significantly different within each other (p > 0.05). All materials presented a significant decrease in degree of conversion and Vickers hardness when compared top to bottom surfaces (p < 0.05). Bottom to top surface ratios for degree of conversion ranged from 0.8 (TEBO and TEPO) to 0.9 (TEBF and TEPF), and from 0.4 (TEPO) to 0.7 (TEBF and TEPF) for hardness. In conclusion, resinous materials present a decrease in hardness and degree of conversion from top to bottom even when a higher power is used, while the flowable material TEPF showed the lowest volumetric shrinkage values compared to the other materials.

Does the combination of whitening toothpaste and hydrogen peroxide bleaching increase the surface roughness and change the morphology of a nanofilled composite?

Aim: To evaluate changes in the surface roughness and morphology of a nanofilled composite following toothbrushing with a whitening (WT) or regular toothpaste (RT), alone or combined with 35% hydrogen peroxide bleaching (HP). Methods: Seventy disc-shaped nanofilled composite (Filtek Z350XT) specimens were randomly divided into groups (n=10): WT, RT, TB (without toothpaste ­ control) or the combinations WT/ HP, RT/HP, TB/HP and HP. All groups underwent toothbrushing simulation (60,000 cycles) and bleaching treatment (4 sessions). Mean surface roughness (Ra, µm) was measured before (T0) and after treatments (TB). Surface morphology was assessed by scanning electron microscopy (SEM) at TB. Mean Ra was analyzed using general mixed models and multiple comparisons by the Tukey-Kramer test (α=5%). Results: HP caused no surface roughness changes on the nanofilled composite after treatment (p>0.05). RT toothbrushing, combined or not with HP, increased the surface roughness (p<0.05). WT and WT/ HP protocols had no effect on the surface roughness of the composite (p>0.05). The nanofilled composite submitted to RT toothbrushing combined with HP (RT/HP) presented substantial surface alterations under SEM, showing deep depressions and round-shaped defects. Toothbrushing with RT combined with the bleaching agent increased exposure of the inorganic fillers. Conclusion: WT toothbrushing, regardless of HP combination, or the single HP protocol had no effect on the surface roughness of the nanofilled composite. However, RT combined with HP negatively affected surface roughness and presented the most noticeable surface changes among groups

Analysis of color stability and degree of conversion of different types of resin composites

Abstract Resin composites containing surface pre-reacted glass (S-PRG) have been introduced to reduce demineralization and improve remineralization of the tooth structure. However, water diffusion within the material is necessary for its action, which can impair its overall physicomechanical properties over time, including color stability. This study aimed to evaluate the color stability and related degree of conversion (DC) of four resin composites. Discs (6 x 4 mm, n = 5/group) of microhybrid (MH), nanofilled (NF), nanohybrid (NH), and S-PRG-based nanohybrid (S-PRG-NH) composites with two opacities (A2/A2E and A2O/A2D) were prepared. Color (CIELab and CIEDE2000) was evaluated with a spectrophotometer after aging in grape juice (2 x 10 min/10mL/7days). The DC was analyzed by using Fourier transform infrared spectroscopy before and after light-curing. Data were statistically analyzed by using two-way analysis of variance and post-hoc least significant difference tests (p<0.05). In the color stability analysis, the interaction between filler type and opacity was significant (CIELab, p = 0.0015; CIEDE2000, p = 0.0026). NH presented the highest color stability, which did not differ from that of MH. The greatest color alteration was observed for S-PRG-NH. S-PRG fillers also influenced DC (p < 0.05). The nanohybrid resin composite presented favorable overall performance, which is likely related to its more stable organic content. Notwithstanding the benefits of using S-PRG-based nanohybrid resins, mostly in aesthetic procedures, professionals should consider the susceptibility of such resins to color alteration, probably due to the water-based bioactive mechanism of action.

In vitro characterization of a novel resin-based restorative material containing alkaline fillers

Abstract Objective: In this study, a comparative evaluation of the physicochemical properties of Cention N and other direct restorative materials was performed. Three restorative materials—a resin-modified glass ionomer (Fuji II LC), an alkasite-based resinous material (Cention N), and a resin composite (Tetric N Ceram)—were characterized in terms of degree of conversion, Knoop hardness number (KHN) ratio, flexural strength, elastic modulus, water sorption, water solubility, microshear bond strength to dentin, immediate microleakage, and radiopacity. Methodology: The microshear bond strength to dentin and microleakage of Cention N were evaluated with and without the application of an adhesive system (Tetric N Bond Universal). A one-way ANOVA test was used to analyze the data in terms of degree of conversion, KHN ratio, water sorption, water solubility, microshear bond strength to dentin, and radiopacity. A two-way ANOVA test (carried out considering the material type and ethanol aging as factors) was used to analyze the data in terms of flexural strength and elastic modulus. The Kruskal-Wallis test was used to statistically analyze the data on microleakage. A significance level of α=0.05 was used for all tests. Results: Fuji II LC was found to have the highest degree of conversion, water sorption, and microleakage, as well as the lowest flexural strength. Cention N had the highest solubility; when used with an adhesive system, it achieved bond strength and microleakage similar to those of the Tetric N Ceram composite. Tetric N Ceram had the highest degree of conversion, KHN ratio, and radiopacity. Conclusion: The properties of Cention N validate its efficacy as an alternative direct restorative material when used in conjunction with an adhesive system.