RESUMEN
Objective@#To explore the effect of different miniscrew placement heights on the distribution of biological forces produced by clear aligner combined with intramaxillary traction for mandibular molar distalization, to identify the miniscrew location that is conducive to the protection of lower anterior tooth anchorage and to provide a reference that can be used when designing clinical treatments.@*Methods@#Mimics, GeomagicStudio 2017, SolidWorks 2016, and Ansys workbench were used to establish finite element analysis models and perform mechanical analysis under the following six working conditions: working condition 1 was the control group without miniscrews; working conditions 2 to 5 had miniscrew in the buccal bone cortex between the first and second molars of the lower jaw 10 mm, 7 mm, 4 mm, and 1 mm from the top of the alveolar crest, respectively; working condition 6 had the miniscrew in the center of the buccal tongue at the anterior edge of the ascending branch of the lower jaw 5 mm above the occlusal plane.@*Results@#On the sagittal axis, miniscrew anchorage caused distal displacement of all teeth. Compared to the control group, in the miniscrew group, the displacement of the anterior molars exceeded that of the second molars. On the vertical axis, the result in the control group was similar to backward bending; the results in the miniscrew groups resembled the effect of a lever, lowering the lateral incisors and canines and raising the central incisors and first premolars. On the coronal axis, the second premolars and the first molars showed lingual displacement in the control group, and only the premolars and first molars showed lingual displacementin the miniscrew groups. The canines were the teeth that were most strongly affected by the change in miniscrew placement height.@*Conclusion@#The higher the miniscrew position is, the stronger the protective effect on the anterior anchorage. According to the miniscrew placement height, the mandibular arch should be properly narrowed, the central incisors and first premolars should be lowered, and the lateral incisors and canines should be raised when designing clinical treatments.
RESUMEN
Objective To design a search and rescue UAV that is portable and user-friendly in order to meet the needs of rescue personnel on the battlefield.Methods Three-dimensional design software CATIA was used to complete the structural design of the UAV body.In order to make full use of the internal space of the UAV body,folding wings were adopted to reduce the volume of the UAV.By using ABAQUS,the finite elements of the key parts of the UAV were analyzed before the modal analysis of the whole vehicle was conducted to verify the reliability of the structure.The robot simulation software Webots was used for motion simulation of the UAV.Results Simulation analysis and test verification suggested that the structural design of the UAV was well-grounded.It could be quickly and properly deployed by means of hand launch or barrels,which made it easier for rescuers to use the UAV.Conclusion The design and simulation research of UAVs with portable folding wings for search and rescue is of great significance for the research and development of physical prototypes.This study is expected to stimulate new ideas for the development of rescue equipment in the PLA,and contribute to miniaturization of UAVs.
RESUMEN
BACKGROUND:The proximal femoral nail antirotation is the preferred treatment for reverse osteoporotic intertrochanteric fractures.Bone cement enhancement can reduce the probability of proximal femoral nail antirotation cut-out and cut-through,but there are no relevant biomechanical studies demonstrating the effect of bone cement content and location on the stress and displacement of the fracture end. OBJECTIVE:To investigate the effects of different contents and locations of bone cement in cement-reinforced proximal femoral nail antirotation on stress,strain,and displacement of reverse osteoporotic femoral intertrochanteric fractures in the elderly by finite element analysis. METHODS:A healthy adult female right femur model was extracted by Mimics software and smoothed in Geometric software.Five types of internal fixation methods of proximal femoral nail antirotation(cementless,cephalic spherical 1 mL,cephalic spherical 2 mL,cephalic spherical 3.4 mL,and cylindrical 5 mL around spiral blade)and femoral intertrochanteric fracture(AO subtype 31-A3.1 type)model were established in Solidworks software.After assembly,the total stress distribution,peak stress and displacement of the five models of implants with the femur were compared in Ansys software. RESULTS AND CONCLUSION:(1)The peak stresses of proximal femoral nail antirotation with head-end spherical 1 mL,head-end spherical 2 mL,head-end spherical 3.4 mL,and cylindrical 5 mL enhanced proximal femoral nail antirotation around the spiral blade respectively were 571.07 MPa(located at the junction of the spiral blade and the main nail),495.45 MPa(located at the junction of the spiral blade and the main nail),467.20 MPa(located at the junction of the main nail and the distal screw connection),642.70 MPa(located at the junction of the main nail and distal screw connection),and 458.58 MPa(located at the junction of the spiral blade and the main nail).(2)The maximum displacements of proximal femoral nail antirotation with head end sphere 1 mL,head end sphere 2 mL,head end sphere 3.4 mL,and with cylindrical 5 mL enhancement around the spiral blade were 9.260 5,7.589 1,7.316 8,6.790 7,and 6.615 7 mm,respectively,all of which were located at the proximal end of the femoral head.(3)These findings revealed that for reverse femoral intertrochanteric fractures treated with proximal femoral nail antirotation,the bone cement enhancement had significant mechanical stability compared with no enhancement,and the enhancement of the spiral blade 5 mL around the perimeter was the best,which is more preferable for aged unstable intertrochanteric fractures.
RESUMEN
BACKGROUND:In the treatment of edentulous maxillary implants supported fixed repair,the selection of upper scaffold structure materials and the design of different distal implant implantation methods have a close influence on the long-term stability of the whole mouth implant repair. OBJECTIVE:To comprehensively explore the influence of three different materials of upper scaffold and two implant fixation designs on the biomechanics of the fixed maxillary implant repair based on the three-dimensional finite element method. METHODS:Based on the conical beam CT data of a healthy adult with normal jaws,the Mimics software was used to separate the maxillary and maxillary dentin three-dimensional solid models,and the Geomagic Studio software was used to construct the three-dimensional finite element model of denture with denture implant and fixed maxillary arch combined with specific model parameters.According to the different designs of distal implants in the maxillary posterior region,two scheme models were established.Scheme 1(Design 1)was designed in accordance with the"All-on-4"design used in clinical practice.Two implants were vertically implanted in the bilateral incisor region of the maxilla,and the other two implants were implanted in the bilateral second premolar region at a 30° angle.In scheme 2(Design 2),two implants were vertically implanted in the lateral incisor region of the maxilla,and two short implants were vertically implanted in the posterior region of the maxilla in the bilateral second premolar region.Three materials(titanium,zirconia and polyether ether ketone)were used to assign values to the upper scaffold structure in the two designs,and six different models were obtained.The biomechanical effects of the implant,surrounding bone tissue and the upper scaffold structure were compared and analyzed in the oblique loading direction. RESULTS AND CONCLUSION:(1)The maximum stress peaks of all models were distributed in the neck region around the posterior implant and the cortical bone under the two edentulous implant fixed restoration schemes,regardless of the material of the upper scaffold.(2)Compared with the alternative design of Design 2,which adopted vertical implantation of short implants,Design 1 showed a more ideal stress distribution on the maxilla.(3)The scaffold model constructed by polyether ether ketone material transferred higher stress to the implant and surrounding bone tissue close to the loading zone of the upper jaw bone,followed by titanium and zirconia.As for the support itself,the peak stress of the upper scaffold of polyether ether ketone was significantly lower than that of the zirconia and titanium scaffolds.Zirconia scaffolds were used among the three upper scaffolds to disperse the stress distribution of implant and bone tissue.(4)The results suggest that both designs can be applied to clinical practice.However,from the perspective of biomechanics,the stress distribution of the implant,surrounding bone tissue and upper scaffold in Design 1 is more rational,which is more conducive to the long-term prognosis of fixed implant repair in patients with edentulous jaws.The upper scaffold material has a certain influence on the stress distribution of the implant-bone interface.
RESUMEN
BACKGROUND:For dislocation of acromioclavicular joint induced by coracoclavicular ligament fracture,single EndoButton Plate reconstruction and double EndoButton Plates reconstruction are common repair methods.Further study on the stress distribution and fracture risk of the two repair methods is of great significance. OBJECTIVE:To study the biomechanical properties of the coracoclavicular ligament,and compare the fixation effect,stress distribution and failure mode of single and double EndoButton Plates reconstruction. METHODS:(1)Finite element simulation analysis:Mimics,Wrap and SolidWorks were used to establish normal coracoclavicular ligament,single EndoButton Plate reconstruction and double EndoButton Plates reconstruction.Ansys software was used to analyze the stress and deformation of the scapula and clavicle of each model under vertical load.(2)Sample experiment:Fifteen intact scapular-clavicle specimens were randomly grouped into five groups,with three specimens in each group.In group A,the acromioclavicular ligament was severed and the coracoclavicular ligament remained intact.In group B,acromioclavicular ligaments and trapeoid ligaments were severed,leaving intact conical ligaments.In group C,acromioclavicular ligaments and conical ligaments were cut off,and the intact traprex ligaments were retained.In group D,acromioclavicular and coracoclavicular ligaments were severed,and coracoclavicular ligaments were repaired by single EndoButton Plate reconstruction.In group E,acromioclavicular and coracoclavicular ligaments were severed,and the coracoclavicular ligaments were repaired by double EndoButton Plates reconstruction.The mechanical experiment was carried out by a mechanical testing machine to analyze the biomechanical status,stress distribution and failure patterns of the scapular-clavicle and clavicle. RESULTS AND CONCLUSION:(1)Finite element simulation analysis:The average stress of coracoclavicular ligament attached specimens was the lowest,and the risk of coracoclavicular fracture was less than that of single and double EndoButton Plates reconstruction.The mean stress of the coracoid process was similar in single and double EndoButton Plates reconstruction,and the fracture risk was similar.(2)Sample experiment:In groups A,B,C,D and E,the stiffness of specimens was(26.4±3.5),(19.8±2.8),(21.3±3.2),(57.7±4.1),and(46.2±2.8)N/mm,respectively;the ultimate loads were(545.5±53.7),(360.1±42.1),(250.9±44.4),(643.5±39.1),and(511.9±31.7)N,respectively;global stiffness in groups D and E was higher than that in group A(P=0.000 06,0.000 3);ultimate load in group D was higher than that in group A(P<0.05);the ultimate load was not significantly different between the group E and group A(P>0.05).Ligament fracture was observed in groups A,B and C and coracoid process fracture was found in groups D and E.(3)These results suggest that from the biomechanical analysis,Single EndoButton Plate reconstruction and double EndoButton Plates reconstruction are effective treatment techniques for coracoclavicular ligament fracture in acromioclavicular joint dislocation,but increase the risk of fracture.The double EndoButton Plates reconstruction dispersed the stress of the steel plate and reduced the contact force between the steel plate and bone,but slightly reduced the ultimate bearing capacity.Single and double EndoButton Plates reconstruction should be selected according to the actual clinical situation.
RESUMEN
BACKGROUND:Due to the treatment of cervical spondylosis,the Zero-P system of the anterior cervical interbody fusion system will have problems such as screw loosening and fracture after operation,so a novel Low-P system has been developed. OBJECTIVE:To compare the effects of the novel Low-P and Zero-P anterior cervical intervertebral fusion systems on the biomechanical properties of adjacent segments of the cervical spine and to perform stress analysis on the internal fixation system,so as to provide a theoretical reference for clinical treatment. METHODS:A complete model of the C1-C7 segment of the cervical spine was established.Based on the effectiveness of the model,a finite element model of Low-P(type Z Low-P and type H Low-P)and Zero-P system implanted in C4-C5 segments was established.The stress distribution of implanted devices and adjacent vertebral nucleus pulposus,fibrous rings and end plates was analyzed under the conditions of forward flexion,posterior extension,lateral bending and rotation. RESULTS AND CONCLUSION:(1)After implantation of Low-P and Zero-P internal fixation devices,the range of motion of the type H Low-P system was large;the maximum stress value of type Z Low-P system was small;the maximum stress of Zero-P on the nucleus pulposus of adjacent segments was large;the maximum stress of end plate was small.(2)The influence of three internal fixation systems on adjacent segment fiber rings was close.(3)The screw stress of the Zero-P internal fixation system was much greater than that of the Low-P system.(4)It is indicated that compared with Zero-P type internal fixation system,the novel Low-P system reduces the stress value of steel plate and screw,which can reduce screw loosening and internal fixation system failure.The Low-P system has less stress on the nucleus pulposus of adjacent discs and reduces disc degeneration in adjacent segments.This paper provides a theoretical basis for the clinical study of a Low-P type internal fixation system.
RESUMEN
BACKGROUND:Among the pathogenic factors of cervical spondylosis,herniation of the intervertebral disc,dislocation of the facet joint and the stenosis of the intervertebral foramen are important factors leading to symptoms in patients.Moreover,inappropriate manipulation may aggravate the possibility of cervical disc rupture,leading to exacerbation of symptoms in patients. OBJECTIVE:To compare the effect between sagittal cervical manipulation and traditional cervical rotation manipulation on the area of the intervertebral disc,facet joint and intervertebral foramen at the operative segment by the finite element analysis. METHODS:The neck CT data of a male volunteer with a normal neck were selected and imported into Mimics 17.0 three-dimensional reconstruction software.Geo-magic Studio 12.0,Solidworks 2017 and Ansys Workbench 17.0 software were used for the construction of the finite element model of cervical vertebrae(C3-6)including intervertebral disc and articular cartilage.The lower end plate of the C5 vertebral body was fixed.A uniformly distributed vertical downward 50 N load was applied on the upper surface of the upper vertebral body(C3).The stress,deformation and deformation direction of the C4-5 intervertebral disc,joint capsule stress,the displacement of facet joints and the area of bilateral intervertebral foramen were compared between sagittal cervical manipulation and traditional rotation reduction. RESULTS AND CONCLUSION:(1)When using the rotation technique,the maximum normal equivalent stress(von Mises stress)of the C4-5 disc was 8.06 MPa;the total deformation was 1.05 mm,and the fiber ring expanded to the left and outside.When using the sagittal tip lifting technique,the maximum normal equivalent stress(von Mises stress)of the C4-5 disc was 2.60 MPa;the total deformation was 0.90 mm,and the fiber ring expanded to the left and back.Compared with the rotation technique,the pressure of the cervical manipulation technique on the disc was less(about 32.3%of the rotation technique),and the deformation degree of the disc was also light(about 85.7%of the rotation technique).(2)When the rotation technique was used,the maximum stresses of the left and right articular capsule ligaments were 0.37 MPa and 1.69 MPa,respectively.The overall displacement of the facet joint was 2.21 mm.The area of the right intervertebral foramen decreased by about 3.8%and the area of the left intervertebral foramen increased by about 0.9%.When the sagittal end lifting manipulation was performed,the maximum stresses of the left and right articular capsule ligaments were 0.27 MPa and 1.70 MPa,respectively;the overall displacement of the facet joint was 1.63 mm;the area of the right intervertebral foramen increased by about 2.6%,and the area of the left intervertebral foramen decreased by about 0.9%.Compared with rotation manipulation,sagittal end lifting manipulation had fewer changes in the displacement of facet joint,joint capsule stress and intervertebral foramen area,so it was safer to operate.(3)In conclusion,compared with cervical rotation manipulation,sagittal end lifting manipulation has fewer changes in facet joint displacement,intervertebral disc stress/deformation degree,joint capsule stress,and foraminal area.In clinical practice,more appropriate manipulation should be selected based on biomechanical results after an accurate assessment of patients'conditions.
RESUMEN
BACKGROUND:Endoscopic treatment of lumbar disc herniation has obvious advantages over traditional open surgery.Endoscopic surgery involves the implantation of a working cannula,which requires only partial bone removal,and there are no studies on the effects of two types of intraoperative foraminoplasty and laminoplasty on the mechanical properties of the local structure of the lumbar spine. OBJECTIVE:To compare the effect of foraminoplasty and laminoplasty on the biomechanical properties of disc and isthmus of the responsible segment. METHODS:The lumbosacral CT images of a healthy male volunteer were taken,and a finite element model M0 of the L3 to sacral vertebrae was established,on which the primary and secondary foraminoplasty models M1 and M2 of the L5/S1 and the laminoplasty model M3 were built.The same load was applied to compare the intervertebral motion range,disc Von Mises stress and equivalent stress characteristics of L5 vertebral isthmus with each model. RESULTS AND CONCLUSION:(1)Compared with M0,M1 and M2 motion range in L5/S1 segment did not change significantly in all directions;M2 overall motion range increased by 8.60%in flexion;M3 increased by 8.23%and 8.26%in L5/S1 right bending and right torsion,and 5.39%and 5.67%in overall motion range in flexion and right bending,with no significant changes in motion range in the rest of working conditions.(2)Compared with M0,M1 showed no significant change in the extremes of Von Mises stress at L5/S1 disc;M2 increased 11.06%,12.50%,18.32%,and 15.48%in flexion,extension,left torsion,and right torsion;M3 increased 12.22%,19.54%,10.05%,and 9.97%in flexion,extension,left torsion,and right torsion,and the rest working conditions and L4/5 disc maximum Von Mises stress did not change significantly.(3)Compared to M0,the maximum Von Mises stress in the left isthmus of L5 of M1 increased by 12.43%in left bending,18.38%,13.29%,13.62%,and 40.00%in the right isthmus in extension,right bending,left torsion,and right torsion.The maximum Von Mises stress in the left isthmus of L5 of M2 increased by 38.87%,42.63%,16.95%,and 19.35%,and that in the right isthmus increased by 12.58%,33.70%,12.92%,and 17.42%in flexion,extension,left bending,and left torsion.The maximum Von Mises stress in the left isthmus of L5 of M3 increased 67.07%,78.14%,32.33%,62.94%,and 89.99%in flexion,extension,left and right bending,and right torsion.(4)The results suggest that foraminoplasty and laminoplasty have a small effect on spinal motion range;there is a mild increase in the extreme values of disc Von Mises stress in the segments operated by interbody laminoplasty and secondary foraminoplasty;there is no significant change in the extreme values of disc Von Mises stress in adjacent segments,and there is a significant increase in the Von Mises stress in the ipsilateral isthmus operated by the interbody laminoplasty model.
RESUMEN
BACKGROUND:Ankylosing spondylitis is a chronic inflammatory disease with chronic rheumatic immunity.Soft tissue ossification and fusion and spinal stiffness can cause biomechanical changes. OBJECTIVE:To reconstruct the lumbar-sacral intervertebral disc in ankylosing spondylitis patients with lumbar kyphosis by finite element analysis,and to study the range of motion of each segment of T11-S1 and the biomechanical characteristics of annulus fibrosus and nucleus pulposus. METHODS:The imaging data were obtained from an ankylosing spondylitis patient with lumbar kyphosis.The original CT image data of continuously scanned spine were imported into Mimics 21.0 in DICOM format,and T11-S1 was reconstructed respectively.The established model was imported into 3-Matic software in the format of"Stl"to reconstruct the intervertebral disc,and the fibrous intervertebral disc model was obtained.The improved model was further imported into Hypermesh software,and the vertebra,nucleus pulposus,annulus fibrosus and ligament were mesh-divided.After the material properties were given,the model was imported into ABAQUS software to observe the range of motion of each vertebral body in seven different working conditions of T11-S1,and analyze the biomechanical characteristics of each segment of annulus fibrosus and nucleus pulposus. RESULTS AND CONCLUSION:(1)The range of motion of L1 vertebrae was higher than that of other vertebrae under six different working conditions:extension,forward flexion,rotation(left and right),and lateral flexion(left and right).The maximum range of motion was 2.18° during L1 vertebral flexion,and the minimum range of motion was 0.12° during L5 vertebral extension.(2)The annular fiber flexion at L2-L3 segments was greater than the extension(P<0.05),and the annular fiber flexion at L3-L4 and L4-L5 segments was less than the extension(P<0.05).The left rotation of L1-L2 annular fibers was greater than the right rotation(P<0.05).The left flexion of the annulus was greater than the right flexion in L1-L2,L2-L3,L3-L4,L4-L5 and L5-S1 segments(P<0.05).(3)The nucleus pulposus stresses of T11-L12,L1-L2,L2-L3,L3-L4 and L4-L5 segments in forward flexion were greater than in extension(P<0.05).The left rotation of T12-L1 and L3-L4 segments was smaller than the right rotation(P<0.05),and that of T11-T12,L1-L2,and L2-L3 segments was larger than the right rotation(P<0.05).The left flexion was larger than the right flexion in the T11-S1 segment.(4)It is concluded that in ankylosing spondylitis patients with lumbar kyphosis,the minimum range of motion of the vertebral body is located at the L5 vertebral body in extension.To prevent fractures,it is recommended to avoid exercise in the extension position.During the onset of lumbar kyphosis in patients with ankylosing spondylitis,the maximum stress of the annulus fibrosus and nucleus pulposus is located in the L1-L2 segment,which is fixed and will not alter with the change of body position.The late surgical treatment and correction of deformity should focus on releasing the pressure of the annulus fibrosus and nucleus pulposus in this segment to avoid the rupture of the annulus fibrosus and the injury of the nucleus pulposus.
RESUMEN
BACKGROUND:Intramedullary nail has achieved a good clinical result in the treatment of femoral shaft fractures,but some patients still have aseptic nonunion due to mechanical instability.The femur is the longest and largest bone in the human body,but there are few studies on whether the fracture of the femur has different biomechanical results in different areas and the influence of different inserting methods on the stability of fracture fragments in different areas. OBJECTIVE:To analyze the biomechanical characteristics of anterograde and retrograde intramedullary nails in the treatment of different areas of femoral shaft fractures,and to evaluate the best way of insertion to reduce the incidence of nonunion. METHODS:CT data of a healthy volunteer were selected to import into the software of Mimics 19.0 and Geomagic studio 2017 to extract and optimize the three-dimensional model of the right femur.The anterograde and retrograde intramedullary nail models were built with Solidworks 2017 software and assembled with femoral shaft fracture models at different fracture areas according to standard surgical techniques.The models were imported into Abaqus 2017 software in STEP format to set material attribute parameters,boundary conditions,load and submit calculation,and the results were viewed in the visualization module.Among them,the antegrade and retrograde intramedullary nails of the upper femoral shaft fracture were A1 and A2 models,B1 and B2 models in the middle segment,and C1 and C2 models in the lower segment. RESULTS AND CONCLUSION:(1)In models A1,B1 and C2,the overall stress distribution of the femur was more uniform,and the placement,the displacement and angle of the fracture site,and inversion angle of the proximal femoral bone fragment were smaller.(2)For the upper and middle femoral shaft fractures,the anterograde intramedullary nail has a better biomechanical effect.For lower femoral shaft fractures,a retrograde intramedullary nail is preferable.
RESUMEN
BACKGROUND:The treatment of distal tibial fractures with soft tissue injury has always been challenging,and the new retrograde tibial nailing is a new choice.Up to now,there were few reports on the biomechanical properties between the new retrograde tibial nailing,anterograde intramedullary nailing and supercutaneous locking plate. OBJECTIVE:To explore the biomechanical stability of new retrograde tibial nailing,antegrade intramedullary nailing and supercutaneous locking plate in the treatment of distal tibial fractures with soft tissue injury using finite element analysis so as to offer a scientific foundation for clinical application. METHODS:The finite element model of transverse distal tibia fracture was established by relevant software utilizing the CT data of the tibia from a 42-year-old healthy male.Retrograde tibial nailing,antegrade intramedullary nailing and supercutaneous locking plate finite element models were assembled under the principle of fracture fixation.Finally,meshing,applying loads,and data processing were accomplished with the ANSYS 2019 software.Moreover,the stress distribution and displacement of the tibia and internal fixation of each model were compared. RESULTS AND CONCLUSION:(1)The displacement of fracture end in the three groups increased with the increase of load.In all mode loads,the average displacement of the fracture end was the least in the retrograde tibial nailing group,followed by the supercutaneous locking plate group,and the highest in the antegrade intramedullary nailing group.At 800 N vertical load,the displacement difference of the fracture end was statistically significant(P<0.05).There was no statistical significance in other load modes.(2)Under different loads,the tibial stress in the three groups was the highest in the middle of the tibia,and gradually decreased to the proximal and distal ends.The stress distribution of the tibial shaft was the highest in the retrograde tibial nailing group,followed by the supercutaneous locking plate group,and the least in the antegrade intramedullary nailing group.(3)Under different loads,the stress of the tibial stress raiser in the three groups was significantly higher in the supercutaneous locking plate group than in the other two groups,with statistical significance(P<0.05).(4)Under different loads,the stress of the fixators in the three groups was the largest in the supercutaneous locking plate group,followed by the retrograde tibial nailing group,and the minimum in the antegrade intramedullary nailing group.There were significant differences in the stress of fixator stress raiser among the three groups under different loading modes(P<0.05).(5)It is indicated that all three fixation methods have the good anti-rotation ability and axial stability.Retrograde tibial nail shows better biomechanical stability.
RESUMEN
BACKGROUND:Three-point mechanics is an effective method for ankle foot orthosis correction and prevention of various foot diseases.At present,the clinical application research on 3D printing ankle foot orthosis has been widespread;however,there are relatively few reports on numerical simulation and finite element analysis involving three-point mechanical correction.There is a lack of relevant biomechanical experimental verification. OBJECTIVE:Three-point force was loaded to analyze the composite model of ankle foot orthosis and foot by finite element method,observing the effect of foot correction with ankle foot orthosis under three-point force intervention,verifying the effectiveness of three-point force and the reliability of ankle foot orthosis. METHODS:A three-dimensional foot and ankle model of a healthy volunteer was constructed based on the medical image processing software Mimics.Rodin 4D and Geomagic reverse engineering software were used to optimize the models and design personalized ankle foot orthosis models.Solidworks software was utilized to turn the ankle model inside for 10° to simulate the foot varus disease.Static loading was carried out on the foot force application area by ANSYS software combined with the three-point mechanics principle.The deformation and stress changes of the foot and ankle tissues were analyzed when the human foot pain threshold was met.The display dynamics was used to further verify the effectiveness of the three-point force applied by the ankle foot orthosis. RESULTS AND CONCLUSION:(1)The personalized ankle foot orthosis designed in this paper had the effect of preventing and fixing foot and ankle varus.The ankle varus was 1.81 mm after being loaded with 1 N·m of varus when not wearing ankle foot orthosis,while it was only 0.44 mm after wearing ankle foot orthosis,the deformation rate was reduced by 75.7%,and the effect of preventing varus was significantly enhanced.(2)When only coronal correction was performed,the low calcaneal force would aggravate the varus angle of the front foot.After adjusting the correction force on the inside of the heel and above the medial malleolus,the varus angle of the front foot and the calcaneus position were improved;however,the medial phalangeal region of the foot still had different degrees of adduction and displacement,which would aggravate the adduction deformity of the patient's front foot.(3)The correction effect of the coronal plane and horizontal plane was better than that of the single coronal plane.There was no adduction and displacement of the medial phalanges of the front foot and the varus angle of the front foot decreased under the force(25,10,10,20 N)of the medial heel,the medial shaft of the first metatarsal,below the lateral malleolus and above the medial malleolus,and the valgus along the X-axis was corrected by 1.395 mm,the calcaneus valgus was corrected by 1.227 mm.The calcaneus varus angle was corrected from 10.21° to 7.25°,and the varus angle was improved by 28.9%.(4)The lateral plantar metatarsal load decreased,the medial plantar metatarsal load increased under the action of a two-plane three-point force,and the plantar bone stress was significantly improved after correction.Thus,the reliability of the three-point force principle was further verified.This study provides an important theoretical support for the implementation of ankle foot orthosis in the treatment of varus in clinical practice.
RESUMEN
BACKGROUND:Less is reported on the influence of cortical bone thickness on displacement and equivalent stress. OBJECTIVE:To analyze the influence of cortical bone thickness on the maximum displacement and equivalent stress at the implant-bone interface through a three-dimensional finite element method,thereby providing some suggestions for oral implantation. METHODS:In this experiment,we selected the cone-shaped CT image data of a patient who was scheduled for mandibular first molar implant restoration.First,we established a mandibular model in Mimics13 software,and then imported it into Solid works 2022 software.According to the related product information,we drew the cone-shaped implant(4.1 mm×10 mm)and the upper prosthesis model.Cortical bone models were obtained according to different cortical bone thicknesses(2.5,2.0,1.5,1.0 mm)and named D1,D2,D3,and D4,respectively.All the models were imported into ANSYS Workbench 2021 software and cross-combined.Finally,we applied vertical and oblique loads to the four groups of models,and analyzed the stress of the models in each group. RESULTS AND CONCLUSION:The peak equivalent stress is lowest in the cancellous bone and highest in the upper prosthesis,that is,at the abutment-implant junction.The peak stress increases with the decrease of cortical bone thickness.The peak stress of the abutment increases with the decrease of cortical bone thickness,and a similar explanation can also be applied to the other implant restoration components.The peak stress in bone tissue and implants increases with the increase of cortical bone thickness.In models D1,D2,D3,the peak stress in implants is higher than that in bone tissue,but the results are reversed in D4.
RESUMEN
BACKGROUND:Anterior subtotal corpectomy,decompression and fusion is a conventional method to treat cervical degenerative diseases.A titanium cage is an important implant to maintain the stability of the cervical spine after subtotal corpectomy.In recent years,many patients have complications such as titanium cage sinking,which are highly controversial. OBJECTIVE:To investigate the internal biomechanical relationship between the tilt angle of the titanium cage and postoperative titanium cage subsidence after anterior subtotal cervical corpectomy,decompression and fusion. METHODS:A three-dimensional finite element model of the C4-C6 segment was established by CT images of a normal human cervical spine,in which the anterior subtotal resection,decompression and fusion of the C5 vertebral body were simulated,and titanium cages with different tilt angles(-6° to-1° negative angle,that is,the front edge of titanium cage is shorter than the rear edge of titanium cage;1° to 6° positive angle,that is,the front edge of titanium cage is longer than the rear edge of titanium cage)were placed.After setting the boundary conditions,preloads of 50,100 and 150 N were applied respectively on the C4 vertebral body.The stress value of each contact point between the titanium cage and C4 lower-end plate and C6 lower-end plate(seven stress contact points on the contact surface of titanium mesh)was recorded and statistical analysis was conducted. RESULTS AND CONCLUSION:(1)The tilt angles of the titanium cage of the positive angle group and negative angle group under 50,100 and 150 N stress respectively were found by Mann Whitn test,with P<0.05,which was statistically significant.The dispersion coefficients of the positive angle group were smaller than those of the negative angle group under 50,100 and 150 N stress conditions.(2)Under 50,100 and 150 N stress conditions,the Wilcoxon sign rank test in the positive angle group of titanium cage tilt angle found that when the angle was set to 1° to 5°,the difference was not statistically significant(P>0.05).However,when the tilt angle of the titanium cage was set to 6°,the difference was statistically significant(P<0.05).(3)Under 50,100 and 150 N stress conditions,the Wilcoxon sign rank test in the negative angle group of titanium cage tilt angle found that when the tilt angle was set to-1° to-6°,the difference was not statistically significant(P>0.05).(4)It is concluded that in the sagittal position,the titanium cage with a positive tilt angle is more stable than with a negative tilt angle,which is more suitable for clinical use.The tilt angle of the titanium cage is relatively stable in the range of 1° to 5°.When the tilt angle is 6°,the stability starts to decline,which is easy to cause complications of titanium cage sinking after surgery.It is more suitable to select the titanium cage with a tilt angle of 1° to 5° according to the clinical situation during surgery to improve the efficacy.
RESUMEN
BACKGROUND:The stability of the pelvis is mainly determined by the posterior pelvic ring and the sacroiliac joint.The posterior pelvic ring injury and the dislocation of the sacroiliac joint caused by high energy impacts such as car accidents increase year by year.Surgical treatment is the best method,and there are many kinds of endophytorepair methods in clinical practice,but which treatment method has the best biomechanical properties is still controversial. OBJECTIVE:To compare the biomechanical properties of three kinds of internal implants:anterior double plates,posterior bridging plate and tension nail in the repair of unilateral unstable pelvic posterior ring injury,to provide a reference for the clinical treatment and development of a new pelvic tension screw. METHODS:(1)Finite element simulation:Mimics,Wrap and SolidWorks were used to establish normal pelvic model,unilateral injured pelvis model,and three kinds of internal implant repaired models(anterior double plates,posterior bridging plate and tension nail).Ansys was used to analyze the stress and deformation of the models.(2)Biomechanical test:A total of 15 intact pelvic specimens were randomly grouped into five groups,normal pelvic model,unilateral injured pelvis model,anterior double plates,posterior bridging plate and tension nail groups.The mechanical test was performed using an Instron E10000 testing machine. RESULTS AND CONCLUSION:(1)Simulation:In the normal pelvic model,the average displacement of the sacrum was 0.174 mm,and the maximum stress of the sacral iliac bone was 10.51 MPa,and the stress distribution was uniform.The mean sacral displacement of the unilateral injured pelvis model was 0.267 mm,and the stress concentration of the model was obvious.The mean displacement of the sacrum in the three repaired models was close to that in the normal pelvic model,and the stress distribution of the sacral iliac bone in the tension nail repaired model was uniform.(2)Mechanical test:The stiffness of the normal pelvic model was(226.38±4.18)N/mm,and that of the unilateral unstable pelvic model was the smallest(130.02±2.19)N/mm.The deviation of the normal pelvic model stiffness and the three repaired models'stiffness were all within(±10%),and the repair effect was obvious.(3)The simulation results were in agreement with the experimental results.(4)The biomechanics of the tension nail repaired model was the most similar to that of the normal pelvis,and this method was the best.The repairing stiffness of the anterior double plate was too large,and the stress shielding effect was more significant.The posterior bridging plate repair could not solve the compensatory effect of the normal side soft tissue and had defects.This study provides an optimal basis for clinical surgery.(5)The new type of pelvic tension nail should be improved from the point of view of the tension nail to retain the good biomechanical properties of the tension nail,while adding other advantages,such as being used for the osteoporotic pelvis.
RESUMEN
BACKGROUND:Anterior cruciate ligament injury tends to lead to secondary meniscus injury and osteoarthritis.At present,there are few studies on the mechanics of meniscus and articular cartilage injury caused by anterior cruciate ligament injury. OBJECTIVE:To study the effect of partial rupture of the anterior cruciate ligament on the stress of medial and lateral meniscus and articular cartilage of knee joint by finite element analysis. METHODS:The CT and MRI images of the knee joint of a healthy volunteer were selected,and the scan data were imported into Mimics,Geomagic and SolidWorks software.After registration and fusion,four kinds of three-dimensional knee joint models were established:models of intact anterior cruciate ligament,rupture of the posterior external tract of anterior cruciate ligament,rupture of the anterior internal tract of anterior cruciate ligament,and absence of anterior cruciate ligament.Finally,data were imported into Ansys software to apply four different modes of loads to the knee joint:Longitudinal loads of 750 N were applied to the top of the femur;longitudinal load of 750 N to the top of the femur and forward thrust of 134 N behind tibia;a longitudinal load of 750 N and a varus moment of 10 Nm were applied to the top of the femur to simulate genu varus;750 N longitudinal load and 4 Nm internal rotation moment were applied to the proximal end of the femur to simulate knee internal rotation.The finite element analysis of biomechanical stress changes of the meniscus and articular cartilage of the knee joint was carried out. RESULTS AND CONCLUSION:(1)In the straight position of the knee joint,when the anterior medial tract of the anterior cruciate ligament was broken and the anterior cruciate ligament was missing under longitudinal loads of 750 N at the top of the femur,the total stress and peak value of meniscus increased significantly,but the stress distribution of the meniscus and the stress of articular cartilage did not change significantly.In longitudinal load of 750 N to the top of the femur and forward thrust of 134 N behind tibia,the fracture of the anterior internal tract of the anterior cruciate ligament increased the tibia forward,the compressive stress of posterior angle of the meniscus increased,and the stress of the articular cartilage did not change significantly.During simulating genu varus,the posterior angular stress of the lateral meniscus decreased,the stress of the medial meniscus increased,and the stress of articular cartilage slightly decreased when anterior cruciate ligament injuries were complete.When the anterior internal tract of the anterior cruciate ligament was broken or absent under knee internal rotation,the equivalent stress peak value of femoral cartilage and tibia cartilage shifted from medial cartilage to lateral cartilage,and the stress peak value of meniscus increased significantly.At this time,the anterior internal tract of the anterior cruciate ligament played a leading role in the rotational stability of the knee joint.(2)These results indicate that the risk of secondary meniscus injury in patients with anterior and medial anterior cruciate ligament band rupture was much higher than that in patients with posterior and external anterior cruciate ligament band rupture when the knee was in the upright standing position,varus and pronation,and there was no significant difference in the impact on articular cartilage.
RESUMEN
BACKGROUND:For teeth with normal dental crown height,pulp cavity retention crown restoration with different depths of the pulp cavity and different repair materials affects the stress and flexural strength of tooth tissue.For short crown molar defects,the research on pulp cavity repair mainly focuses on clinical observation and in vitro flexural strength experiments. OBJECTIVE:To establish a three-dimensional finite element model for short crown molar restored by the endocrown after root canal treatment to analyze the effects of different pulp cavity retention depths and different repair materials on the distribution and size of dentin equivalent stress. METHODS:Based on establishing the complete model of the short crown mandible first molar,a three-dimensional finite element model was established for repairing the distal adjacent defect of the short crown molar with different pulp cavity retention depths(h=2,3,4 mm)and different repair materials(zirconia,lithium disilicate).Under the oblique loading,the equivalent stress distribution was observed.The peak value of dentin equivalent stress and the mean value of equivalent stress near the bottom of the mesial pulp cavity wall were calculated. RESULTS AND CONCLUSION:(1)Equivalent stress concentration areas:The stress of complete short crown molar and restored models mainly concentrated in the mesial root mesial neck and mesial root lingual neck.The stress concentration area was found in the mesial pulp cavity wall corresponding to the bottom layer of restored models,and the stress concentration was obvious in the 4 mm retention depth group.(2)Under the same repair material,the peak value of dentin equivalent stress was the lowest at 3 mm for all models after repair.The average value of equivalent stress near the bottom of the mesial pulp cavity wall was lowest at 3 mm.(3)Under the same retention depth,there was no significant difference between the two materials in the dentin equivalent stress peak and the mean value near the bottom of the mesial pulp cavity.(4)The results showed that under the conditions of this experiment,the endocrown was used to repair the defect of the short crown molar and the retention depth was 3 mm,which was more beneficial to protect the remaining dental tissue.The selection of zirconia or lithium disilicate as the repair material had little effect on the dentin stress.
RESUMEN
BACKGROUND:Calcaneal defects are common in clinical practice.It is difficult for surgeons to evaluate the effect of calcaneal reconstruction due to the complex anatomical structure and motor function of the heel.Finite element analysis has become an effective method for biomechanical behavior simulation and numerical analysis. OBJECTIVE:To compare the clinical effect and biomechanical characteristics of total calcaneal reconstruction with the Ⅱ-shaped and V-shaped fibular flap. METHODS:CT images of one left foot of a healthy 50-year-old male were acquired.Mimics software was used to obtain the preliminary three-dimensional model.Geomagic software was used to trim and curve the model.The model was imported into Solidworks software to simulate calcaneal reconstruction and complete the pre-processing of finite element calculation.Finally,Ansys software was used to solve the problem.The simulation results were compared with previous literature results to verify the effectiveness of the model.The surgical effect and biomechanical characteristics of the foot in different gait phases based on the simulated stress results were analyzed. RESULTS AND CONCLUSION:(1)Both Ⅱ-shaped and V-shaped fibular flaps could be used to reconstruct completely missing calcaneus,which could restore the length,width and height of normal calcaneus,and fill up the missing calcaneus bone.(2)Compared with the normal calcaneus,both configurations of fibular flaps showed a tendency for over-concentration of stress after loading.The normal calcaneus stress was mostly concentrated around the calcaneus nodule,the subtalar process and the calcaneus groove,while the stress of the two fibular flaps was mostly concentrated at the junction between the bone flap with the talus and cuboid bones.(3)The maximum stress of calcaneus was different between the two models and normal calcaneus under different simulation conditions,with statistically significant differences(P＜0.05).Compared with the V-shaped fibular flaps,Ⅱ-shaped fibular flaps had less force change in different gaits and were closer to the normal calcaneus.The V-shaped fibular flap bore excessive stress during the period of push-off,and the grafted bone material may yield under this condition and have the risk of fractures.
RESUMEN
BACKGROUND:The traditional fixation method for femoral neck fractures is three hollow screws inverted triangle fixation,and the optimal fixation method for femoral neck fractures that have not achieved anatomical reduction is inconclusive. OBJECTIVE:To compare the biomechanical properties of cannulated screws internal fixation for sub-capitated femoral neck fracture with different reduction qualities based on finite element analysis. METHODS:The three-dimensional digital model was reconstructed using CT data of the proximal femur from a healthy male volunteer.The femur was modeled to sub-capitated femoral neck fractures.Fracture models were divided into anatomical reduction group,coxa vara group,and coxa valgus group.All fracture model groups were transferred using the standard group,screw depression group,and screw elevation group.A vertical downward stress of 1 400 N was applied to the femoral head at the top of the acetabulum.The displacement and stress distribution of the femur and internal fixator under different fixation methods were observed,and the maximum stress and displacement of the femur and fixator were compared. RESULTS AND CONCLUSION:(1)For anatomical reduction femoral neck fracture,the peak stress of fixation in the standard group,screw depression group and screw elevation group was 41.35,31.27 and 43.32 MPa,respectively.The maximum peak stress of the femur was found on the screw elevation group(28.58 MPa),and the standard group had the maximum peak displacement.(2)During hip varus,the stresses in the three subgroups were relatively dispersed and even.The peak stress of the femur in the standard group was the smallest,but the peak displacement was the largest.The stability of fixation might be poor.The peak displacement of the femur in the screw depression group was the smallest.(3)In the hip valgus,obvious screw stress concentration appeared in the screw depression group,and the peak displacement was the largest among the three subgroups,and an in-out-in phenomenon appeared.The peak stress of the screws in the screw elevation group was the largest among the three subgroups,but the peak displacement was the smallest.(4)It is concluded that for sub-capitated femoral neck fractures that are completely anatomically reduced,it is recommended to use standard inverted triangular nails for fixation.When the hip varus and hip valgus occur within the allowable range of the reduction standard,it is recommended to use the inverted triangle screw to fix it by rotating the corresponding angle in the same direction as the hip varus or valgus.
RESUMEN
BACKGROUND:The patella-patellar tendon junction is a high-incidence area of injury in patellar tendinopathy.The rabbit patella-patellar tendon injury model is a commonly used animal experimental research object.At present,the stress analysis of the injury mechanism and modeling method is not comprehensive. OBJECTIVE:Based on the previous histological and mechanical measurements,this study used micro CT to scan and model the whole patella,the patella-patellar tendon junction and the tendon quadriceps junction,to analyze the characteristics of changes in stress,and explore the potential impact of different forms of exercise on patellar tendon degeneration so as to provide a theoretical basis for injury prevention and animal model establishment. METHODS:Female healthy adult New Zealand rabbits were selected to study the patella and tendons at both ends of the left knee joint.After the material was taken,the samples were scanned and saved with micro CT.Mimics,Geomagic Studio and SolidWorks were used to establish a three-dimensional model.Finite element analysis was carried out with Ansys Workbench.The equivalent displacement,stress and strain of the target region were analyzed under different loading conditions(load size and direction changes,different action modes). RESULTS AND CONCLUSION:(1)Load direction change affected trend and value change;load size change affected value change.(2)Compared with other areas,the stress concentration was more obvious at the insertion point of the patellar tendon,and the strain value was the lowest.(3)At the insertion point of the patellar tendon,the stress concentration was greater in valgus than in varus and pronation than in extorsion.(4)The stress concentration effect and stress shielding during knee flexion and extension are the main causes of patellar tendon insertion injury.The stress in pronation and valgus states is also a potential factor leading to damage,which needs further study.The animal model established by jumping and running is more in line with the characteristics of sports injury.