The effect of different framework's material on strain induced in distal abutment in mandibular Kennedy's class II: an in-vitro study / O efeito de diferentes materiais de estrutura na deformação induzida na distal do pilar da classe II de Kennedy mandibular: um estudo in vitro

Objective: This study aims to compare the strain induced in the supporting structures of unilateral mandibular removable partial denture frameworks retained by extra-coronal attachments fabricated with three different materials. Material and Methods: Three mandibular class II digitally designed and printed acrylic models with detachable abutments were used to fabricate three removable partial denture framework with extra coronal attachments from three different materials. A total of 33 models were prepared for strain testing (n=11). Models were divided into three groups according to framework's material: porcelain fused to cobalt chromium (PFM), polyetherketoneketone (PEKK) and polyetheretherketone (PEEK) group. Unilateral load of 60 N was applied in the three groups and strains were measured around the main abutment and saddle area using strain gauge. Results: Statistical analysis was performed using Shapiro-Wilk's test and by checking data distribution. Data were found to be non-parametric and were analysed using Kruskal-Wallis test followed by Dunn's post hoc test with Bonferroni correction. PFM group showed significantly the highest strain values around abutment, slot 1 (1mm distal to the socket of the last abutment) and slot 2 (1 cm away from slot 1) respectively (843.00±23.08, 91.00±6.52 and 1274.00±65.71) than the other tested groups (p<0.05) at same tested sites respectively followed by PEKK group (384.00±37.48, 81.00±2.24 and 135.00±0.00) and PEEK group (29.00±4.18, 63.00±4.47 and 52.00±5.70). Conclusions: PEEK and PEKK for partial denture framework with extra coronal attachments are adequate alternative to PFM due to their good mechanical response applying less strain on supportive structures in free-end cases. PEEK induces lower strain magnitude on the supporting structures when compared to PEKK. (AU)

Objetivo: Este estudo tem como objetivo comparar a tensão induzida nas estruturas de suporte de estruturas de próteses parciais removíveis mandibulares unilateraisretidas por encaixes extracoronários fabricados com três materiais diferentes. Material e Métodos: Três modelos mandibulares de classe II digitalmente projetados e impressos em acrílico com pilares destacáveis foram usados para fabricar três estruturas de próteses parciais removíveis com encaixes extracoronários de três materiais diferentes. Um total de 33 modelos foram preparados para testes de deformação (n=11). Os modelos foram divididos em três grupos de acordo com o material da estrutura: porcelana fundida com cobalto-cromo (PFM), poliétercetonacetona (PEKK) e polieteretercetona (PEEK). Carga unilateral de 60 N foi aplicada nos três grupos e as deformações foram medidas em torno do pilar principal e área de sela usando medido de tensão. Resultados: A análise estatística foi realizada por meio do teste de Shapiro-Wilk e com a verificação da distribuição dos dados. Os dados mostraram-se não paramétricos e foram analisados pelo teste de Kruskal-Wallis seguido pelo de Dunn com correção de Bonferroni. O grupo PFM mostrou significativamente os maiores valores de tensão ao redor do pilar, slot 1 (1mm distal do último pilar) e slot 2 (1 cm de distância do slot 1) respectivamente (843,00±23,08, 91,00±6,52 e 1274,00±65,71) do que os outros grupos testados (p<0,05) nos mesmos locais testados, respectivamente, seguido pelo grupo PEKK (384,00±37,48, 81,00±2,24 e 135,00±0,00) e grupo PEEK (29,00±4,18, 63,00±4,47 e 52,00±5,70). Conclusão: PEEK e PEKK para estrutura de prótese parcial com encaixes extracoronários são alternativas adequadas ao PFM devido à sua boa resposta mecânica aplicando menos tensão nas estruturas de suporte em casos de extremidade livre. O PEEK induz menor magnitude de deformação nas estruturas de suporte quando comparado ao PEKK (AU)

Esofagotomía y cierre primario por cuerpo extraño en esófago superior / Esophagotomy and primary closure due to foreign body in the upper esophagus

RESUMEN Los cuerpos extraños en el esófago son un problema frecuente en urgencias, debido la mayoría de las veces a ingestión accidental. Presentamos el caso de una paciente femenina de 50 años, sin antecedentes patológicos, que consulta por presentar la ingesta de prótesis dental mientras almorzaba, con posterior disfagia, odinofagia y dolor cervical. Se le realizan radiografías y tomografía computarizada (TC) donde se evidencia imagen radiopaca en esófago cervical. Se interconsulta con el Servicio de Gastroenterología, dada la imposibilidad de extracción de la prótesis por vía endoscópica. Se realiza luego cervicotomía lateral izquierda de emergencia, con esofagotomía, extracción del cuerpo extraño y cierre primario del esófago. La obstrucción del esófago por cuerpos extraños puede ocasionar muchas complicaciones. La consecuente demora en el tratamiento puede llevar a un marcado aumento de la mortalidad. Por eso, en este caso, se prioriza la cirugía ante un riesgo elevado de perforación y hemorragia.

ABSTRACT Esophageal foreign bodies are a common problem in the emergency department, usually due to accidental ingestion. We report the case of a 50-year-old otherwise healthy female patient who sought medical care due to dysphagia, odynophagia and cervical pain after swallowing a partial denture while having lunch. The patient underwent X-rays and a computed tomography (CT) scan which showed a radiopaque image in the upper esophagus. After a failed attempt to remove the denture through endoscopy, surgery was decided via a left lateral emergency cervicotomy with esophagotomy, foreign body removal and primary closure of the esophagus. Esophageal obstruction due to foreign bodies may cause many complications. Treatment delays may result in increased mortality. Thus, in this case we prioritized surgery due to high risk of perforation and bleeding.

Fréquence et déterminants de l'édentement partiel des adultes dans les institutions médicodentaires de Kinshasa, en République Démocratique du Congo

Contexte et objectifs. La perte de dents appelée édentement affecte la mastication, la parole, l'esthétique, le comportement social et la qualité de vie. L'objectif de la présente étude était d'évaluer la fréquence et les determinants de l'édentement partiel (EP) chez les adultes dans les institutions médico-dentaires de Kinshasa. Méthodes. C'était étude transversale analytique conduite entre octobre 2019 et juillet 2021 dans quelques institutions médico-dentaires de Kinshasa auprès des patients adultes congolais. Les variables d'intérêts étaient la fréquence et les causes de l'EP, les facteurs sociodémographiques et la présence du diabète et/ou de l'hypertension artérielle (HTA). Les déterminants de l'EP ont été recherchés par l'analyse de régression logistique multivariée. Résultats. Quatre cent vingt sept patients ont été inclus. Leur âge moyen était de 37,9 ±15,4 ans. La fréquence de l'EP était de 71%. Seul le statut diabète et/ou hypertension a été indépendamment associé à l'EP (ORa : 23,8 ; IC 95% : 3,2-174,8). Conclusion. La fréquence de l'EP était très élevée chez les adultes, influencée par la presence du diabète et/ou HTA.

Influence of Khat Extract (Catha edulis) on corrosion resistance of Co-Cr dental alloys / Influência do extrato de Khat (Catha edulis) na resistência à corrosão de ligas dentais Co-Cr

Objective: The aim of this experimental study was to assess the effect of khat extract with different concentrations on the corrosion resistance of cobalt-chromium (Co-Cr) dental alloys used for removable denture. Material and Methods:The corrosion resistance of three Co-Cr alloys (Neobond II®, Kera 501® and PD Casta H®) was evaluated in artificial saliva in presence of three different concentrations of khat extracts. Fusayama-Meyer artificial saliva was used as a reference solution. The corrosion properties of the alloys were analyzed using potentiodynamic polarization, electrochemical impedance spectroscopy and surface analysis. The data was presented in means, standard deviations, and related figures. Comparison between the different concentrations was done using 1-way ANOVA test. The surface analysis was performed using scanning electron microscopy (SEM). Results: the results showed that the corrosion resistance of the three alloys tested (Neobond II®, Kera 501® and PD Casta H®) decreased in artificial saliva containing khat extract compared with that of the reference solution. Additionally, the corrosion resistance of the three Co-Cr dental alloys decreased by increasing the concentration of khat extract. Furthermore, the results indicate that Neobond II® alloy showed the least corrosion resistance compared with that of Kera 501® and PD Casta H® alloys. Conclusion: Khat extract with different concentrations had negative impact on the corrosion resistance of Cr-Co alloys. More in-vivo studies are highly recommended to confirm the results of the present study (AU)

Objetivo: O objetivo deste estudo experimental foi avaliar o efeito do extrato de khat em diferentes concentrações na resistência à corrosão de ligas dentárias de cobalto-cromo (Co-Cr) utilizadas em próteses removíveis. Material e Métodos:A resistência à corrosão de três ligas de Co-Cr (Neobond II®, Kera 501® e PD Casta H®) foi avaliada em saliva artificial na presença de três concentrações diferentes de extratos khat. A saliva artificial de Fusayama-Meyer foi usada como solução de referência. As propriedades de corrosão das ligas foram analisadas usando polarização potenciodinâmica, espectroscopia de impedância eletroquímica e análise de superfície. Os dados foram apresentados em médias, desvios-padrão e figuras relacionadas. A comparação entre as diferentes concentrações foi feita usando o teste One-way ANOVA. A análise de superfície foi realizada em microscopia eletrônica de varredura (MEV). Resultados: os resultados mostraram que a resistência à corrosão das três ligas testadas (Neobond II®, Kera 501® e PD Casta H®) diminuiu na saliva artificial contendo extrato khat em comparação com a solução de referência. Além disso, a resistência à corrosão das três ligas dentais Co-Cr diminuiu com o aumento da concentração de extrato de khat. Além disso, os resultados indicam que a liga Neobond II® apresentou a menor resistência à corrosão em comparação com as ligas Kera 501® e PD Casta H®. Conclusão: O extrato de Khat com diferentes concentrações teve impacto negativo na resistência à corrosão de ligas de Cr-Co. Mais estudos in vivo são altamente recomendados para confirmar os resultados do presente estudo. (AU)

Comparative study of some mechanical properties of cobalt chromium and polyether ether ketone thermoplastic removable partial denture clasps: an In-vitro Study / Estudo comparativo de algumas propriedades mecânicas dos grampos parciais removíveis termoplásticos removíveis termoplásticos de cobalto cromo e éter cetona: um estudo in vitro

Objective: was to evaluate the retentive force, fatigue resistance and deformity of clasps made from two materials cobalt chromium and poly ether ether ketone (PEEK). Material and Methods: sixteen models were fabricated,each one having lower 1st molar. Models were divided into two groups according to materials,group I (GI) for cobalt chromium (Co-Cr) and group II (GII) for PEEK. Each testing models and its clasps were mounted inside universal testing machine, the retention was measured by applying withdrawal force to it by this machine at 5 mm/min. The Fatigue resistance is measured by the reduction in retention through repeated insertion and removal cycles using robota chewing simulator. Removal and insertion cycling of clasps was carried out for 360, 730, 1080, 1,440, 2,116 and 2,880 cycles (corresponding to 3, 6, 9, 12, 18 and 24 months of simulated clinical use of a RPD) to simulate the fatigue resistance test. Deformity was measured before and after each cycling using a digital micrometer. Statistical analysis was done by 2-way-ANOVA test to detect significance effects of each variable. Results: Retention and fatigue resistance, after 360, 730, 1080, 1,440, 2,116 and 2,880 cycles totally the difference between Co-Cr and PEEK groups was statistically non-significant (P = 0.0980> 0.05) where (Co-Cr > PEEK). Deformation results, regardless to evaluation time, Co-Cr group recorded statistically significant higher deformation mean value than PEEK group (P = 0.008 < 0.05).Regardless to material group, deformation mean value changed nonsignificantly by time (P = 0.2882> 0.05). Conclusion: PEEK clasps (1.0 mm in cross section diameter) engage 0.50 mm undercut provide sufficient retention nearly similar that of Co-Cr clasps.(AU)

Objetivo: o objetivo foi avaliar a força de retenção, a resistência à fadiga e a deformidade dos grampos fabricados com dois materiais diferentes: cromo-cobalto (Co-Cr) e poliéter-éter-étercetona (PEEK). Materiais e métodos: dezesseis modelos foram confeccionados, cada um com 1º molar inferior. Os modelos foram divididos em dois grupos de acordo com o material: grupo I Co-Cr e grupo II para PEEK. Cada modelo de teste universal e seus grampos foram montados em uma máquina de teste universal. A retenção foi medida aplicando força de retirada por esta máquina a 5 mm/min. A resistência à fadiga foi medida pela redução na retenção através de ciclos repetidos de inserção e remoção usando um simulador do ciclo de mastigação. O ciclo de remoção e inserção dos grampos foi realizado por 360, 730, 1080, 1.440, 2.116 e 2.880 ciclos (correspondendo a 3, 6, 9, 12, 18 e 24 meses de uso clínico simulado de um RPD) para simular o teste de resistência à fadiga. A deformidade foi medida antes e após cada ciclo, usando um micrômetro digital. A análise estatística foi realizada pelo teste ANOVA de 2 fatores para detectar os efeitos de significância de cada variável. Resultados: A retenção e a resistência à fadiga após 360, 730, 1080, 1.440, 2.116 e 2.880 ciclos entre os grupos Co-Cr e PEEK não mostrou diferença estatisticamente significativa (p = 0,0980> 0,05), onde (Co-Cr> PEEK). Para os resultados da deformação, independentemente do tempo de avaliação, o grupo Co-Cr registrou um valor médio de deformação maior, com diferença estatística significativa, quando comparado com o grupo PEEK (p= 0,008 < 0,05). Independentemente do grupo de material, o valor médio da deformação foi alterado de forma não significativa pelo tempo (p= 0,2882> 0,05). Conclusão: os grampos PEEK (1,0 mm de diâmetro da seção transversal) engatam 0,50 mm retenção quase semelhante à dos grampos Co-Cr (AU)

Clinical and sociodemographic evaluation of peri-implant health of implant retained prostheses fabricated with an immediate oclusal loading protocol / Avaliação clínica e sociodemográfica da saúde peri-implantar de próteses retidas em implantes fabricadas com um protocolo de carga oclusal imediata

ABSTRACT Introduction Dental implant therapy, when well planned, can contribute to the patient's quality of life and is an important tool for solving a serious public health problem in various parts of the world. Objective This study investigated peri-implant health in fixed implants supported by an immediate loading technique and to associate those outcomes with sociodemographic conditions. Material and method After the disassembly of the prostheses on implants with the "Branemark Model" the peri-implant health of 93 patients was evaluated using dental plaque index (DPI), probing pocket depths (PPD), bleeding on probing (BOP), clinical attachment levels (CAL), and presence of gingival hyperplasia. Patients also answered a questionnaire about their gender, age, socioeconomic status (Brazilian Association of Research Companies - ABEP), general health and tobacco use. Result The most constant clinical findings were the presence of plaque, followed by gingival hyperplasia and periimplantitis, which was associated with disease progression. Most of the patients in the study were female, Caucasian, and under 60 years of age, with prostheses located in their lower arch, and they belonged to social classes A and B. Conclusion The presence of dental biofilm occurred in almost all implants and was not related to the presence of periimplantitis. The progression of periimplantitis with bone loss was related to sub gingival bleeding. The sociodemographic characteristics in the study did not present great correlations with the clinical variables of the dental implants studied.

RESUMO Introdução A terapia de implantes dentais, quando bem planejada, pode contribuir para a qualidade de vida do paciente e é uma ferramenta importante para solucionar um sério problema de saúde pública em várias partes do mundo. Objetivo Este estudo investigou a saúde peri-implantar em implantes fixos apoiados por uma técnica de carga imediata e associou esses resultados a condições sociodemográficas. Material e método Após a desmontagem das próteses sobre implantes com o "Modelo de Branemark", a avaliação peri-implantar de 93 pacientes foi avaliada por meio do índice de placa dental (IPD), profundidade de sondagem (PS), sangramento à sondagem (SS), níveis clínicos de fixação (NCF) e presença de hiperplasia gengival. Os pacientes também responderam a um questionário sobre sexo, idade, nível socioeconômico (Associação Brasileira de Empresas de Pesquisa - ABEP), saúde geral e tabagismo. Resultado Os achados clínicos mais constantes foram a presença de placa, seguida de hiperplasia gengival e periimplantite, que esteve associada à progressão da doença. A maioria dos pacientes do estudo era do sexo feminino, caucasiana e com idade inferior a 60 anos, com próteses localizadas na arcada inferior, pertencentes às classes sociais A e B. Conclusão A presença de biofilme dentário ocorreu em quase todos os implantes e não foi relacionado à presença de periimplantite. A progressão da peri-implantite com perda óssea foi relacionada ao sangramento subgengival. As características sociodemográficas do estudo não apresentaram grandes correlações com as variáveis clínicas dos implantes dentários estudados.

Prosthetic treatment for Down's syndrome patient with dental cross bite problem using maxillary double crown denture / 대한치과보철학회지

Patients with Down's syndrome have several dental complications such as small teeth caused by underdevelopment of dentin and enamel, periodontitis, agenesis of teeth, prolonged retention of primary teeth and malocclusion due to narrow palate. Removable denture with maxillary double crowns would be a good treatment option to solve the problems of the patient with Down's syndrome. Double crowns compensate the insufficient support and retention of denture and easily solve the cross bite problem. Double crowns also allow easy repair of denture in case of abutment teeth extraction. In this case, 26-year-old female patient with Down's syndrome and dental phobia had small number of teeth with enamel hypoplasia, prolonged retention of primary teeth and dental cross bite. Prosthetic treatment was done using removable denture with double crowns in the maxilla. In the mandible, teeth preparation was done on enamel margin without anesthesia. Anterior laminate and posterior complete zirconia crown restorations were performed. As a result, the cross bite was effectively corrected by denture with double crowns. Pronunciation and appearance were also improved without extraction of teeth and dental anesthesia.

Restoration of bilateral distal extension removable partial denture using a fixed implant prosthesis in unilateral partial edentulous patient: A case report / 대한치과보철학회지

Traditional removable partial denture is a successful treatment for partial edentulous patients. When the abutment is formed with unilateral minority teeth, satisfaction with the use of removable partial denture may be lowered due to patient's discomfort and damage of the abutment. Recently, it has been reported that the unilateral posterior extension partial denture is used as a bilateral posterior extension partial denture using implant fixed prostheses as abutments. In this case, by using implant surveyed crown prostheses, bilateral posterior extension partial denture is fabricated in site that is predicted to have a poor prognosis. This resulted in improved support, maintenance, and stabilization of the removable partial denture, which were economically beneficial to patient and satisfied with use.

Evaluation of two interforaminal implants and implant-assisted removable dentures on stress distribution: an in vitro study

OBJECTIVES: In mandibular edentulism, the treatment option with a two-interforaminal implant-retained bridge and a removable partial denture is rarely evaluated in literature. The aim of this in vitro study was to evaluate the stress distribution of this treatment option by comparing it with traditional treatment options with interforaminal implants in the edentulous mandible. MATERIALS AND METHODS: Two interforaminal implants were placed in a formalin-fixed cadaver mandible, and overdentures with three different types of attachments were fabricated: (1) two ball attachments and an overdenture, (2) a Dolder bar and an overdenture, and (3) screw-retained two-implant inter-canine porcelain fused to a metal bridge and an implant-assisted removable denture (IARD) with precision attachments. Three biting conditions were generated for each denture type, and the strains were documented under vertical loading of 100 N. RESULTS: The calculated strain values from measured strains in all measurement sites and loading conditions for the screw-retained two-implant inter-canine porcelain fused to a metal bridge and a cast framework partial denture with precision attachments situation were lower than in the other scenarios (P<0.05). CONCLUSION: Within the limitations of the present study, it can be concluded that an IARD may be a reasonable and valuable alternative to ball attachments or a bar in two interforaminal implants, especially when the patients prefer to be able to show their teeth even when they take out their removable dentures.

Estudio comparativo de la desadaptación entre los puentes odontológicos ceramometálicos de tres unidades: puente odontológico convencional vs. puente odontológico con perno buje / A comparative study of the misfit between three-unit metal-ceramic dental bridges: conventional dental bridge vs. pin hub dental bridge

Las coronas individuales presentan un nivel de desadaptación con las piezas dentarias que se magnifica de manera significativa en las estructuras de Prótesis Parcial Fija como son las férulas y el puente odontológico (PO). Esta desadaptación es la consecuencia geométrica de la sumatoria de errores de las cabezas de empotramiento de los PO convencionales, a la que hemos denominado un cruce angular o sinergia de errores. Para evitar dicha sumatoria de errores, hemos desarrollado un elemento protético que denominamos Perno Buje (PB) que permite, tanto en Prótesis Parcial Fija como en Prótesis Implanto Asistida, obtener más precisión con este tipo de estructuras construídas en dos piezas y soldadas en frío que con las construídas en una sola pieza. Este estudio ha demostrado una clara evidencia de que el comportamiento del PB genera una gap menor y más predecible que el PO convencional (AU)

The individual crowns show a level of teeth failure rehabilitation that is significantly magnified in partial fixed prosthesis as in splints and dental bridges. This failure, called angular cross or mistake sinergy, is the geometric consequence of the number of mistakes that conventional dental bridge fitted heads produce. In order to avoid this sum of mistakes, a prothetic element called Pin Hub has been developed. This element allows more accuracy in this kind of structures made of two pieces and cold welding than the ones made out of one piece; not only in partial fixed prothesis but also in assisted implant prosthesis. This study has proved that the Pin Hub creates a minor and more predictable gap that the one produced by a conventional dental bridge (AU)

Alternativa estética ante la pérdida de piezas primarias en el sector anterior: resolución clínica / Esthetic alternative to the loss of primary pieces in the previous sector

La pérdida de piezas permanentes en el sector anterior sigue siendo una preocupación clínica en el tratamiento odontológico de niños y adolescentes. Es importante destacar que la pubertad y la adolescencia son etapas donde las relaciones con los pares son de suma importancia. Las restauraciones protéticas convencionales no cumplen las expectativas estéticas, pero siguen siendo el tratamiento de elección, ya que los implantes solo pueden ser realizados una vez finalizados el crecimiento y el desarrollo. Los sistemas adhesivos mediante cinta de fibra de vidrio han simplificado el trabajo, brindando una alternativa intermedia conservadora y estética. El objetivo de este trabajo es presentar la resolución clínica en dos pacientes que concurrieron a la Cátedra de Odontología Integral Niños luego de haber sufrido traumatismos que provocaron la pérdida de piezas dentarias permanentes logrando la restitución de la longitud de arco, la devolución de la estética y la fonación con la colocación de una prótesis tipo Maryland, realizada con cinta de fibra de vidrio preimpregnada con resina compuesta (AU)

Premature loss of anterior permanent teeth is still a cause for concern in dental treatment of children and adolescents. Social relationships with peers are particularly important during puberty and adolescence. Removable prosthesis has always been a choice but they may not satisfy patients' esthetic expectations and dental implants can only be placed after the jaw has finished growing. Adhesive directly bonded splints with glass fibers reinforced composite resins can be an alternative to conventional space maintainers. The aim of this report is to describe the treatment of two patients who attended at the Department of Comprehensive Children´s Dentistry after suffering traumatic dental injuries using bridges as an approach to restore arch length, esthetics and function (AU)

Empreinte sectorielle en occlusion

L'empreinte sectorielle en occlusion est souvent citée dans la littérature comme une méthode alternative pour réaliser des empreintes en prothèse conjointe, avec une variété de matériaux et de techniques d'empreinte. Elle présente de nombreux avantages par rapport aux techniques d'empreintes classiques. Le présent article a pour but de passer en revue les différentes indications, avantages et limites de l'empreinte sectorielle en occlusion, pour ensuite présenter la mise en oeuvre de cette technique, à travers deux cas cliniques

Clinical application of mandibular removable partial denture using implant-supported surveyed crown: A case report / 대한치과보철학회지

When making conventional removable partial denture for the remaining teeth where the remaining teeth are only on one side, rotation of the denture occurs -in function- on the axis of the connected remaining teeth. If the edentulous portion is long, it becomes harder to obtain retention and stability for the abutment as the importance of the mucous membrane support is elevated. Such movements of denture decrease denture retention and stability, put excessive stress on the abutment, and give bad influence on periodontal health. Therefore, additional implant placement can be of a good choice in gaining additional retention and stability for partial denture. Thus hereby we report this clinical case as successful results were obtained by placing implants symmetrical to the remaining teeth and putting implant-supported surveyed crowns on the implants, allowing the partial denture to be designed to accept varying components and to have suitable path of insertion.

Implant assisted removable partial denture with implant surveyed crown: A 20-month follow-up case report / 대한치과보철학회지

Traditional options for posterior edentulous treatment include removable partial dentures and implant fixed prostheses. Recently, the concept of implant assisted removable partial denture, in which two treatments are fused, has been introduced in consideration of systemic health and patient's needs, costs, residual alveolar bone status and so on. Implant assisted removable partial denture has the advantage of increasing the retention and stability of the denture and improving its esthetics in cases of large bone defects or biomechanical disadvantages. In addition, it is possible to strategically place the implants in a site where the alveolar bone is relatively sufficient, thereby overcome the limit of the conventional removable partial denture design as well as reducing the burden on a wide range of implant surgery. Cost reduction is also expected. In this case, the patient was treated by placing the implant in both premolar sites of the mandible and fabricating the distal extension removable partial denture with the implant fixed prosthesis as an abutment. After delivering the definitive prosthesis, the patient showed satisfaction with the masticatory function and esthetics. and has been regularly followed-up for more than one year. The following 20-months follow-up case report describes the design of an implant-assisted-removable partial denture (IARPD) in which two cementretained implant crowns used to provide support and stability.

Pónticos ovoides en el manejo de tejidos blandos, zona posterior con y sin extracción: reporte de dos casos clínicos / Ovate pontics in soft tissue management, posterior zone with and without extraction: report of two clinical cases

Un problema que sucede a menudo en la práctica clínica es la ausencia dental por diversos factores. Esto conduce a un gran desafío para surehabilitación, ya que debido a la pérdida dentaria se genera un colapsodel reborde alveolar, lo que ocasiona alteración en la morfología óseay gingival, o en diversos casos, se realizaron extracciones sin una planeación restaurativa, por lo que su sustitución implica mayores procedimientos. Una alternativa a esta ausencia dental es el diseño de póntico ovoide, siempre y cuando cumpla los requisitos clínicos para un mejor resultado estético, funcional e higiénico. El objetivo de este artículo es mostrar el empleo del póntico ovoide en el sector posterior con distintos aspectos clínicos: por un lado, utilizando la técnica de conformación del lecho gingival a presión y por el otro, la técnica directa postextracción, mediante prótesis fija de tres unidades en metal/porcelana.

A problem that often occurs in clinical practice is the dental absence caused by various factors. This leads to a great challenge for rehabilitation since due to tooth loss, a collapse of the alveolar ridgeis generated, causing an alteration in bone and gingival morphology; also, in many cases, extractions were made without restorative planning, so their replacement involves major procedures. An alternative to this dental absence is ovate pontic design, provided it meets the clinical requirements for better esthetic, functional and hygienic result. The aim of this article is to show the use of the ovoid pontic in the posterior region with different clinical aspects: first, using the technique of forming the gingival bed under pressure and on the other, postextraction direct technique through a three-unit fi xed prosthesis in metal/porcelain.

Angulated implants for fabrication of implant supported fixed partial denture in the maxilla

Until recently, angled abutments have been the only solution to correcting the trajectory of the emergence profile of labially inclined implants in the maxilla. However, the clinical implications of angled abutments reveal several shortcomings. Newly designed angulated implants with a 12-degree restorative platform angula-tion are an alternative to angled abutments. The purpose of this article was to report a case utilizing new angulated implants [Co-axis, Keystone dental, Burlington, MA, USA] in the premaxilla thereby facilitating fabrication of a multi-unit implant re-tained fixed dental prosthesis

Theoretical axial wall angulation for rotational resistance form in an experimental-fixed partial denture

PURPOSE: The aim of this study was to determine the influence of long base lengths of a fixed partial denture (FPD) to rotational resistance with variation of vertical wall angulation. MATERIALS AND METHODS: Trigonometric calculations were done to determine the maximum wall angle needed to resist rotational displacement of an experimental-FPD model in 2-dimensional plane. The maximum wall angle calculation determines the greatest taper that resists rotation. Two different axes of rotation were used to test this model with five vertical abutment heights of 3-, 3.5-, 4-, 4.5-, and 5-mm. The two rotational axes were located on the mesial-side of the anterior abutment and the distal-side of the posterior abutment. Rotation of the FPD around the anterior axis was counter-clockwise, Posterior-Anterior (P-A) and clockwise, Anterior-Posterior (A-P) around the distal axis in the sagittal plane. RESULTS: Low levels of vertical wall taper, ≤ 10-degrees, were needed to resist rotational displacement in all wall height categories; 2–to–6–degrees is generally considered ideal, with 7–to–10–degrees as favorable to the long axis of the abutment. Rotation around both axes demonstrated that two axial walls of the FPD resisted rotational displacement in each direction. In addition, uneven abutment height combinations required the lowest wall angulations to achieve resistance in this study. CONCLUSION: The vertical height and angulation of FPD abutments, two rotational axes, and the long base lengths all play a role in FPD resistance form.

Removable prosthetic rehabilitation in patient with maxillofacial defects caused by gunshot: A case report / 대한치과보철학회지

Maxillofacial defect comes from congenital defect, trauma and surgical resection. Patients with intraoral defect are commonly related to maxillary defect and they need prosthetic rehabilitation. Functional reconstruction of partially edentulous mandible has many limitations. However, if both condyles are intact, maxillofacial prosthesis using partial denture give competent results. In this case, a patient of 58 year-old male has a defect on palate and left mandibular posterior teeth from gunshot. The maxillary defect of this patient is Class IV according to Aramany classification and the mandibular one is Type V according to Cantor and Curtis classification. For retention of the obturator, remaining teeth are fully utilized and artificial teeth are arranged harmoniously to provide stable occlusion. Mandibular RPD covered limited range of deformed soft tissue derived from mandibular resection surgery. With these treatments, the patient in this case showed improvements in mastication, swallowing and speech.

RPD framework fabrication using computer-aided design (CAD) and rapid prototyping / 대한치과보철학회지

Nowadays, digital dentistry is generally applied to prosthodontics with fabrication of inlays or any other fixed prostheses by utilizing CAD/CAM (computer-aided design/computer-aided manufacturing) technology and intraoral scanner. However, in fabricating removable prosthesis, there are some limitations for digital technology to substitute conventional casting method. Therefore, approaching removable prostheses fabrication with CAD/CAM technology would be a meaningful trial. In this case report, Kennedy class III mandibular edentulous patient who was in need of increasing the vertical dimension of occlusion was treated with removable partial denture using CAD and rapid prototyping technique. Surveying and designing the metal framework of the partial denture was performed with CAD, and sacrificial plastic pattern was fabricated with rapid prototyping technique. During the follow up period of nine months, the removable partial denture has provided satisfactory results in esthetics and function.

Implante transalveolar en sustitución de una corona espiga de pronóstico dudoso* / Transalveolar implant to replace a pin crown of doubtful prognosis

La sustitución de los dientes perdidos en la región estética presenta un complejo desafío debido a la dificultad en la reforma de la apariencia natural y de la anatomía papilar. Se Presenta un caso clínico donde se sustituyó un diente con corona espiga de pronóstico dudoso, por un implante inmediato Avanza. Se trata de una paciente de 24 años de edad atendida en la consulta multidisciplinaria de Implantología de la Clínica Docente de Prótesis de Marianao. Tenía una corona espiga en el incisivo central superior derecho, con cambio de coloración que le afectaba su estética. Además se le caía constantemente y estaba ligeramente inflamada por vestibular, lo cual le producía dolor. Después de una evaluación multidisciplinaria y el consentimiento de la paciente, se procede a la retirada de la corona espiga y exodoncia de la raíz del 11 mediante la técnica de colgajo. Inmediatamente se colocó el implante Avanza y se rehabilitó con una prótesis parcial acrílica removible por razones estéticas. Con este tratamiento, la paciente mantuvo el contorno de los tejidos blandos y la altura ósea de la zona intervenida, necesarios para alcanzar excelentes resultados estéticos(AU)

Replacement of missing teeth from the esthetic region poses a complex challenge to dental specialists due to the difficulties involved in reforming natural appearance and papillary anatomy. A clinical case is presented in which a tooth with a pin crown of doubtful prognosis was replaced with an immediate Avanza implant. A 24-year-old female patient presented at the implantology multidisciplinary service of Marianao Prosthetics University Clinic. The patient had a discoloring pin crown in the upper right central incisor that affected her esthetic appearance. Furthermore, the crown constantly fell out and there was slight vestibular swelling, which caused pain. After multidisciplinary evaluation and having obtained the patients consent, the pin crown was removed and root 11 extracted by flap technique. An Avanza implant was immediately placed and rehabilitated with a removable acrylic partial denture for esthetic reasons. With this treatment, the patient maintained the soft tissue contour and bone(AU)