Finite element analyses of retention of removable partial denture circumferential clasps manufactured by selective laser melting / 北京大学学报(医学版)

OBJECTIVE@#To compare the retentions of different designs of cobalt-chromium (Co-Cr), pure titanium (CP Ti), and titanium alloy (Ti-6Al-4V) removable partial denture (RPD) circumferential clasps manufactured by selective laser melting (SLM) and to analyze the stress distribution of these clasps during the removal from abutment teeth.@*METHODS@#Clasps with clasp arm size A (1.9 mm width/1.1 mm thickness at the body and 0.8-taper) or B (1.2 times A) and 0.25 mm or 0.50 mm undercut engagement were modeled on a prepared first premolar die, named as designs A1, A2, A3, and A4, respectively. The density and elastic modulus of SLM-built Co-Cr, CP Ti, and Ti-6Al-4V were measured and given to different groups of clasps. The density, elastic modulus, and Poisson ' s ratio of enamel were given to the die. The control group was the cast Co-Cr clasp with design A1, to which the density and elastic modulus of cast Co-Cr alloy were given. The Poisson's ratio of all metals was 0.33. The initial 5 N dislodging force was applied, and the maximum displacement of the clasp along the insertion path was computed. The load was reapplied with an increment of 5 N than in the last simulation until the clasp was completely dislodged. The retentive force range of different groups of clasps was obtained. The retentive forces of the SLM-built Co-Cr, CP Ti, and Ti-6Al-4V clasps with equivalent computed retentive force range to the control group were validated through the insertion/removal experiment. The von Mises stress distributions of these three groups of SLM-built clasps under 15 N loads were analyzed.@*RESULTS@#SLM-built Co-Cr, CP Ti, and Ti-6Al-4V clasps with designs B1 or B2, and Co-Cr clasps with design A2 had higher retentive forces than those of the control group. SLM-built CP Ti and Ti-6Al-4V clasps with design A1 had lower retentive forces than those of the control group. SLM-built Co-Cr clasp with design A1 and SLM-built CP Ti and Ti-6Al-4V clasps with design A2 had equivalent retentive forces to those of the control group. The insertion/removal experiment showed that the measured retentive forces of these three groups of SLM-built clasps were (21.57±5.41) N, (19.75±4.47) N, and (19.32±2.04) N, respectively. No statistically significant measured retentive force difference was found among these three groups of SLM-built clasps (P>0.05). The maximum von Mises stress of these three groups of SLM-built clasps exceeded their responding yield strength except for the Ti-6Al-4V one.@*CONCLUSION@#SLM-built Co-Cr circumferential clasps had higher retention than CP Ti and Ti-6Al-4V ones with the same clasp arm size and undercut engagement. The retention of SLM-built circumferential clasps could be adjusted by changing the undercut engagement and clasp arm size. If SLM-built circumferential clasps are used in clinical practice, the Ti-6Al-4V clasp with clasp arm size A and 0.50 mm undercut engagement is recommended considering the long-term use of RPD in the patient's mouth.

Influencia de parámetros de diseño sobre el comportamiento biomecánico de un implante dental corto / Influence of design parameters on the biomechanical behavior of a short dental implant

Introducción: Los implantes dentales deben transmitir esfuerzos al tejido óseo y generar deformaciones que favorezcan el equilibrio entre los procesos de formación y reabsorción ósea. Debido al alto número de pacientes que presentan maxilares con dimensiones reducidas, es necesario estudiar el comportamiento biomecánico de implantes dentales cortos. Objetivos: Evaluar el efecto de los parámetros de diseño: diámetro máximo, longitud de la interfaz hueso-implante y altura del filete de la rosca sobre el comportamiento biomecánico de un nuevo diseño de implante dental corto. Métodos: Los modelos tridimensionales del implante dental corto fueron creados usando el software Autodesk Inventor Profesional versión 2011 (Autodesk Inc, California, USA) y analizados con el software de elementos finitos Autodesk® Algor® Simulation (Autodesk Inc, California, USA). Resultados: Los niveles máximos de esfuerzos equivalentes de von Mises se obtuvieron, en el hueso cortical peri-implantar. Las cargas aplicadas al implante generaron, en el hueso trabecular peri-implantar, los mayores esfuerzos equivalentes de von Mises en la región apical y los menores valores en la región próxima al hueso cortical. Además, los mayores valores de deformación se obtuvieron en el hueso trabecular para todos los modelos estudiados. Conclusiones: En general, los resultados de las simulaciones mostraron que la mayoría de los modelos estudiados generan esfuerzos y deformaciones en el hueso cortical peri-implantar en niveles que estimulan el crecimiento y la remodelación ósea. No obstante, en algunas de las variantes simuladas se observaron niveles de esfuerzos y deformaciones, en zonas del hueso trabecular peri-implantar, que pueden provocar pérdida ósea en los maxilares. Las variables diámetro del implante y altura del filete de la rosca exhibieron la mayor influencia sobre los esfuerzos y deformaciones máximas generados en el tejido óseo(AU)

Introduction: Dental implants should transmit stresses to the bone tissue and generate strain levels that favor the balance between the bone formation and bone resorption processes. Due to the high number of patients with reduced jawbone dimensions, it is essential to study the biomechanical behavior of short dental implants. Objective: Evaluate the effect of the design parameters: Maximum diameter, Length of the bone-implant interface and Thread depth on the biomechanical behavior of a new design of short dental implant. Methods: The 3D models of the short dental implant were created using Autodesk Inventor Professional software (Autodesk Inc, California, USA) and analyzed by finite elements with Autodesk® Algor® Simulation software (Autodesk Inc, California, USA). Results: The maximum von Mises equivalent stress was obtained in peri-implant cortical bone. The loads applied to the implant generated in peri-implant cancellous bone, the highest von Mises equivalent stress in the lower end of the apical region and the lowest stress values in the region next to the cortical bone. In addition, the highest strain values were obtained in cancellous bone for all models under study. Conclusions: In general, the simulation results showed that most of the models under study generate stresses and strains in peri-implant cortical bone at levels that stimulate bone growth and bone remodeling. However, for some models, it was observed levels of stress and strain in peri-implant cancellous bone that could provoke the bone onset. The variables Implant diameter and Thread depth exhibited the greatest influence on the maximum stresses and strains obtained in the bone tissue(AU)