Preparation and antibacterial properties of Cu-ZnO-loaded dental veneering porcelain / 口腔疾病防治

Objective@#To investigate the antibacterial properties, biocompatibility and mechanical properties of Cu-ZnO-loaded dental veneering porcelain to provide an experimental basis for the development of new dental veneering porcelain. @*Methods@#Cu-ZnO nanoparticles were added to IPS E.max Ceram for restorative veneer porcelain at different mass percentages of 0 wt%, 1 wt%, 2 wt%, 3 wt%, 4 wt%, 5 wt%, and 6 wt% using ball milling in ceramic powder. A cylindrical specimen with a diameter of 20 mm and a thickness of 2 mm was prepared by high-temperature sintering. Scanning electron microscopy was used to observe the surface morphologies of nano-Cu-ZnO and the specimens. The antibacterial effect of Escherichia coli (E. coli) was quantitatively studied by the plate colony counting method. The CCK-8 method was used to evaluate in vitro the cytotoxicity of the tested piece to mouse fibroblasts (L929). Live and dead cells were observed by fluorescence microscopy. The mechanical properties of modified IPS E. Max Ceram veneering porcelain were tested by a three-point bending strength test. @* Results @# Under the scanning electron microscope, Cu-ZnO appears with a block-like structure and can be seen dispersed in the veneering porcelain. When the nano Cu-ZnO loading was 1 wt%, 2 wt%, 3 wt%, and 4 wt%, the antibacterial rates of the specimens were 24.85%, 67.94%, 96.92%, and 99.99%, respectively, and the difference between the experimental groups and the control group was statistically significant (F = 23.308,P = 0.001). The relative growth rate of each group was greater than 80% after coculture with mouse fibroblast cells (L929) for 1 day and 3 days, and there was no significant difference between the groups. The morphology of L929 cells was normal after coculture for 24 hours. With the increase in the Cu-ZnO concentration, the flexural strength of the specimen exhibited an increasing trend followed by a decreasing trend. The bending strength of the specimen loaded with 3 wt% nano Cu-ZnO reached the maximum value (84.728 ± 6.82) MPa, and there was no statistically significant difference between groups (F = 0.633,P = 0.702).@*Conclusion@#The antibacterial rate of IPS E. max Ceram veneering porcelain loaded with 3 wt% nano Cu-ZnO was more than 96% against E. coli after high-temperature sintering at 750 ℃. The bending strength reached the maximum (84.728 ± 6.82) MPa, and there was no obvious cytotoxicity.

Influence of diode laser and warm air drying on the shear bond strength of Lithium di-silicate to Dentin. An in-vitro study / Influência do laser de diodo e da secagem com ar quente na resistência ao cisalhamento do Di-silicato de Lítio a dentina. Um estudo in-vitro

Objective: The current study aimed to evaluate the effect of diode laser irradiation (980 nm) and warm air drying (50°C) on shear bond strength between Lithium di-silicate (IPS e.max; Ivoclar) and human dentin using both (Etch & Rinse) adhesive, Adper™ Single Bond 2 (3M ESPE) and (Self-etch) adhesive, Single Bond UniversalTM(3M ESPE) before adhesive polymerization. Material and Methods: 54 sound lower molars were sectioned to obtain flat dentinal surfaces. Specimens were divided into 2 equal groups (n=27): Group 1 (ER) and Group 2 (SE) according to bonding approach. Each subgroup was subdivided according to dentin surface treatment into 3 equal subgroups (n=9): Control (Co), Diode laser irradiation (L) and Warm air drying (W). All specimens were adhesively cemented to IPS e.max® CAD discs using RelyX™ Ultimate Clicker™(3M ESPE) resin cement. Samples were then subjected to pre-loading in a thermodynamic manner. All samples were tested for shear bond strength using computer-controlled material testing machine. Data analysis was performed using two-way (ANOVA) (p< 0.05) followed by pair-wise Tukey's post-hoc tests. Results: In (SE) group, the subgroup (W) had the highest shear bond strength values followed by (Co) subgroup and the least was (L) subgroup with statistically significant difference. As for (ER) group, the subgroup (W) had the highest shear bond strength values followed by (Co) subgroup and the least was (L) subgroup with no statistically significant difference. Conclusion: Warm air drying for (SE) bonding approach increased shear bond strength of Lithium di-silicate to human dentin and can be introduced as a new effective protocol.(AU)

Objetivo: o objetivo do estudo atual é avaliar o efeito da radiação do laser de diodo (980nm) e secagem de ar quente (50°C) na resistência ao cisalhamento entre dissilicati de Lítio (IPS e.max; Ivoclar) e a dentina humana usando ambos modelos de adesivos (condicionamento total) Adper™ Single Bond e (auto-condicionante) Single Bond Universal™ (3M ESPE), Single Bond UniversalTM (3M ESPE) antes da fotopolimerização. Material e Métodos: 54 segundos molares inferiores foram selecionados para obter superfícies dentinárias planas. Os espécimes foram divididos em 2 grupos iguais (n=27): grupo 1 (ER) e grupo 2 (SE) de acordo com protocolo de adesividade. Cada grupo foi subdividido de acordo com o tratamento de superfície dentro de 3 subgrupos iguais (n=9): Controle (co), irradiação com laser de diodo (L) e secagem com ar quente (W). Todos os espécimes foram adesivamente cimentados a discos de IPS emax CAD usando RelyX Ultimate Clicker (3M ESPE) cimento resinoso. As amostras foram então submetidas a pré-carregamento de forma termodinâmica. Todas as amostras foram testadas para resistência a cisalhamento usando máquina de teste de materiais controlados por computador. A análise de dados foi realizada usando ANOVA dois fatores (p<0.05) seguindo por testes de Tukey pareado como test post-hoc. Resultados: No grupo (SE), o subgrupo (W) apresentou maiores valores de resistência ao cisalhamento seguindo o subgrupo (Co) é o menor foi o subgrupo (L) com diferença estatisticamente significativa. Já para o grupo (Er), o subgrupo (W) apresentou os maiores valores de resistência ao cisalhamento seguido do grupo (Co) e o menor foi o subgrupo (L) sem diferença estatisticamente significante. Conclusão: a secagem com ar quente para a abordagem de adesividade (Se) aumentou a resistência ao cisalhamento do dissilicato de lítio à dentina humana e poderia ser introduzido como um novo e eficaz protocolo(AU)

Faible performances diagnostiques de l'IPS cheville de repos par rapport au doppler artériel des membres inférieurs dans le diagnostic de l'AOMI chez le patient coronarien: à propos d'une série hospitalière / Weak diagnostic performance of resting ankle ABI compared with lower limb's arterial Doppler in the diagnosis of PAD in coronary patients: about a hospital serial study

Introduction. L'index de pression systolique (IPS) est considéré comme un outil indispensable, pour la prise en charge de l'artériopathie oblitérante des membres inférieurs (AOMI), cependant un complément d'exploration par les autres testes physiologiques, IPS au gros orteil et IPS effort s'impose afin de réduire le nombre des faux négatifs. Objectif. Démontrer le faible apport de l'IPS cheville de repos par rapport à l'échodoppler artériel des membres inférieurs dans le diagnostic de l'AOMI. Matériels et méthodes. Sur une série de 300 malades coronariens consécutifs durant l'année 2016 hospitalisés dans le service de cardiologie de l'hôpital universitaire de Constantine, un dépistage de l'AOMI a été réalisé par les investigations suivantes : Mesure de l'IPS à la cheville, compléter par la mesure de l'IPS a l'orteil si incompressibilité artérielle et par la mesure de l'IPS d'effort si l'IPS de repos est limite. Un échodoppler artériel des membres inférieurs a été réalisée par un échographe vividE9 General Electric pour l'ensemble de nos malades, en utilisant une sonde à balayage linéaire 12L, destinée à l'exploration vasculaire périphérique permettant d'obtenir un dépistage ciblé, Le traitement et l'exploitation des données ont fait appel au logiciel SPSS22. Résultats. Une sensibilité modérée de l'ordre de 50%, face à une spécificité élevée avoisinant 100% de l'IPS cheville de repos par rapport à l'échodoppler artériel des membres inférieurs. Sensibilité nettement améliorer après complément par les autres testes physiologiques qui sont la prise de l'IPS cheville effort et la mesure de l'index de pression systolique au gros orteil. Conclusion. L'examen vasculaire des membres inférieurs associe à la mesure de l'IPS cheville couplée aux autres testes physiologique (IPS au gros orteil et IPS effort) assurent une bonne sensibilité et spécificité diagnostiques de l'AOMI

An evaluation of the effect of different veneer materials on fracture resistance of zirconia core / Avaliação dos diferentes efeitos de materiais de revestimento na resistência à fratura do núcleo de zircônia

Objectives: this in vitro study was done to evaluate the effect of packable P60 composite and Tetric N-Ceram composite veneer material on fracture strength of zirconia cores. Material and Methods:Twenty four zirconium cores (Vita, Germany) with 0.7 mm thickness were fabricated by CAD/CAM technology and then subjected to air abrasion with 50 µm of Al2O3. Cores were randomly divided into three groups according to veneering material (group A: control group sandblasted with 50 µm Al2O3 veneered by IPS E-max Ceram porcelain, group C: sandblasted with 50 µm Al2O3, etching with hydrofluoric acid and veneered with P60 composite, group E: sandblasted with 50 µm Al2O3, etching with hydrofluoric acid and veneered with Tetric N-Ceram composite). All crowns were subjected to fracture strength test in the testing machine, with load application by steel ball indenter and 0.5 mm/min. cross head speed. Results: statistical analysis was carried out utilizing one-way ANOVA, LSD. The results of fracture strength value test showed the highest mean value was registered for group (A), and the lowest mean for group (E). One-way ANOVA test represented that, there was a statistically high significant different among all groups. LSD results showed a high significant difference increase in fracture resistance for Group A at p value (*p < 0.001 High significant). Conclusions: Within the limitation of this study, sandblasting zirconia core with 50 µm Al2O3 and veneering with conventional ceramic produced restoration with acceptable fracture resistance value (AU)

Objetivo: o objetivo desse estudo in vitro foi avaliar o efeito dos compósitos P60 compactáveis e material laminado de compósitos Tetric-N Ceram na resistência à fratura de núcleos de zircônia. Material e métodos:Vinte e quatro núcleos de zircônia (Vita, Germany) com 0.7 mm de espessura fabricados por tecnologia de CAD/CAM e sinterizados em alta temperatura (1450ºC por 60 min) de acordo com as instruções do fabricante. Núcleos totalmente de zircônias foram submetidos a abração com 50 µm de Al2O3. Os núcleos de zircônia foram divididos de forma randomiza em três grupos de acordo com o material de revestimento (grupo A: grupo controle jateado com 50 µm Al2O3 folheado com porcelana IPS E-max Ceram, grupo C: jateado com 50 µm Al2O3 , coberto com concentração 9,5% de ácido fluorídrico e folheado com resina composta compatível, grupo E: jateado com 50 µm Al2O3 coberto com concentração 9,5% de ácido fluorídrico e folheado com porcelana IPS E-max Ceram. Todos os espécimes (coroas) foram submetidos a teste de resistência a fratura com máquina de teste universal, essa máquina utilizou para aplicação de carga bola de aço com 6mm de diâmetro 0,5 mm/min de velocidade da cruzeta. Resultados: análise estatística foi realizada utilizando One-way ANOVA, LSD. O resultado da resistência a fratura mostra que o maior valor médio foi registrado no grupo A e a menor média para o grupo E. O resultado do teste One-Way ANOVA representaram que houve uma diferença estatisticamente alta e significante entre todos os grupos. LSD foi executada para mostrar a fonte de significância. Os resultados do LSD mostraram um aumento da diferença significativa alta na resistência à fratura para o grupo A no valor de p (p < 0.001 signicancia alta). Conclusão: Dentro das limitações desse estudo o uso convencional de jateamento com 50 µm Al2O3 e estratificação com cerâmica convencional produziu restauração com valor aceitável de resistência a fratura (AU)

One-year clinical evaluation of IPS Empress CAD versus polished Celtra Duo ceramic Laminate veneers (randomized controlled clinical trial) / Avaliação clínica de um ano de IPS Empress CAD versus laminados de cerâmica Celtra Duo polidos (ensaio clínico randomizado controlado)

Objective: To evaluate fracture resistance and survival rate of IPS Empress CAD versus Polished Celtra Duo ceramic laminate veneers. Material and Methods:Thirty-six ceramic laminate veneers were fabricated for maxillary anterior teeth. The patients were divided into two groups according to the material Group 1(control group) fabricated from IPS Empress CAD laminate veneers and group 2 (intervention group) fabricated from Polished Celtra Duo laminate veneers. Standardized the same preparation with butt joint design and chamfer finish line located supra gingival were performed for all the teeth. The fabrication of the veneers was performed using Cad\Cam (Ceramill motion) machine, with software (Exocad). The veneers surfaces were treated and silanated according to the manufacture instruction of each ceramic and enamel surfaces were etched where total etch adhesive protocol was obeyed using BISCO. Follow up sessions were done every two months up to one year for each patient using dental probe and operator vision to evaluate the fracture, survival rate, marginal adaptation, sensitivity and caries. according to USPHS criteria (United States Public Health Service). This was performed by an experienced, blinded investigator. Results: Fracture resistance, marginal adaptation, retention, caries and sensitivity were evaluated according to the criteria of USPHS and we found there is no significant difference as both groups scaled zero score. Conclusion: Both IPS Empress Cad and Polished Celtra Duo laminate veneers revealed successful clinical performance in terms of fracture resistance, marginal adaptation, retention, and sensitivity after one year follow up period (AU)

Objetivo: Avaliar a resistência à fratura e a taxa de sobrevivência de laminados de cerâmica IPS Empress CAD versus Celtra Duo polidos. Material e Métodos: Trinta e seis facetas cerâmicas laminadas foram confeccionadas para dentes anteriores superiores. Os pacientes foram divididos em dois grupos de acordo com o material Grupo 1 (grupo controle) confeccionado com laminados IPS Empress CAD e grupo 2 (grupo intervenção) confeccionado com laminados Celtra Duo polidos. A mesma forma de preparo e acabamento de chanfro localizado supra-gengival padronizados foram realizados para todos os dentes. A confecção das facetas foi realizada em máquina Cad \ Cam (Ceramill motion), com software (Exocad). As superfícies laminadas foram tratadas e silanizadas de acordo com as instruções do fabricante de cada cerâmica e as superfícies de esmalte foram condicionadas seguindo o protocolo adesivo de condicionamento ácido total com BISCO. Sessões de acompanhamento foram realizadas a cada dois meses durante um ano para cada paciente usando sonda exploradora e visão do operador para avaliar a fratura, taxa de sobrevivência, adaptação marginal, sensibilidade e cárie; de acordo com os critérios USPHS (Serviço de Saúde Pública dos Estados Unidos). Isso foi realizado por um investigador experiente e cego. Resultados: a resistência à fratura, adaptação marginal, retenção, cárie e sensibilidade foram avaliadas de acordo com os critérios da USPHS e não encontramos diferença significativa, pois ambos os grupos escalonaram pontuação zero. Conclusão: As facetas laminadas IPS Empress Cad e Celtra Duo polido revelaram desempenho clínico bem-sucedido em termos de resistência à fratura, adaptação marginal, retenção e sensibilidade após um período de acompanhamento de um ano. (AU)

Mechanical and thermal stress analysis of hybrid ceramic and lithium disilicate based ceramic CAD-CAM inlays using 3-D finite element analysis / Análise do estresse mecânico e térmico de inlays de cerâmica hibrida e de cerâmica a base de dissilicato de lítio através da análise em 3D de elementos finitos

Objective: The aim of this study was to analyze mechanical and thermal stresses of hybrid ceramic and lithium disilicate based ceramic of CAD/CAM inlays using 3D Finite element analysis. Material and Methods:A three dimensions finite element model of permanent maxillary premolar designed according to standard anatomy with class II cavity preparation for inlay restored with two different ceramic materials: 1- Hybrid ceramic (Vita Enamic), 2- Lithium disilicate based ceramic (IPS e.max CAD). Totally six runs were performed on the model as: One loading case for each restorative material was tested in stress analysis; seven points of loading with 140N vertically applied at palatal cusp tip and cusp slop, marginal ridges and central fossa while the models base was fixed as a boundary condition in the two cases. Two thermal analysis cases were performed for each restoration material by applying 5ºC and 55ºC on the crown surface including the restoration surface. Results:The results of all structures were separated from the rest of the model to analyze the magnitude of stress in each component. For each group, maximum stresses on restorative materials, cement, enamel, and dentin were evaluated separately. Both ceramic materials generated similar stress distribution patterns for all groups when a total occlusal load of 140 N was applied. Conclusion: Thermal fluctuations of temperature have a great influence on the stresses induced on both restoration and tooth structure. IPS e.max CAD produced more favorable stresses on the tooth structure than Vita Enamic. (AU)

Objetivo: O objetivo deste estudo foi analisar o estresse mecânico e térmico de inlays de cerâmica hibrida e a base de dissilicato de lítio através da análise em 3D de elementos finitos. Material e Métodos: Foi realizado o design de um modelo de três dimensões em elementos finitos de um pré-molar superior de acordo com os padrões anatômicos de um preparo de cavidade classe II para restauração de inlay em dois tipos de cerâmicas diferentes: 1 Cerâmica hibrida (Vita Enamic), 2 ­ Cerâmica a base de dissilicato de lítio (IPS e.max CAD). No total, seis execuções foram realizadas no modelo como: Uma carga para cada material restaurador foi testado para análise de tensão; sete pontos de carga com 140N foi aplicado verticalmente na ponta da cúspide palatina, saliência da cúspide, cristas marginais e fossa central enquanto a base do modelo foi fixada como uma condição de limite nos dois casos. Duas análises térmicas foram realizadas para cada material de restauração, aplicando 5ºC e 55ºC na superfície da coroa, incluindo a superfície da restauração. Resultados: Os resultados de todas as estruturas foram separados do resto do modelo para analisar a magnitude do estresse de cada componente. Para cada grupo, o máximo de estresse nos materiais restauradores, cemento, esmalte e dentina foram avaliados separadamente. Padrões similares de distribuição de estresse foram gerados em todos os grupos para ambos os materiais cerâmicos, quando a carga oclusal de 140 N foi aplicada. Conclusão: As variações térmicas de temperatura têm uma grande influência nas tensões induzidas na restauração e na estrutura dentária. IPS e.max CAD produziu tensões mais favoráveis na estrutura dentária do que o Vita Enamic (AU)

Derivation of endothelial cells from porcine induced pluripotent stem cells by optimized single layer culture system

A platform to understand amyotrophic lateral sclerosis (ALS) and extend human motor neurons longevity / Plataforma para empezar a comprender la esclerosis lateral amiotrófica (ELA) y extender la longevidad de neuronas motoras humanas

In vitro modeling of neurodegenerative diseases is now possible by using patient-derived induced pluripotent stem cells (iPS). Through them, it is nowadays conceivable to obtain human neurons and glia, and study diseases cellular and molecular mechanisms, an attribute that was previously unavailable to any human condition. Amyotrophic lateral sclerosis (ALS) is one of the diseases that has gained a rapid advance with iPS technology. By differentiating motor neurons from iPS cells of ALS- patients, we are studying the mechanisms underlying ALS- disease onset and progression. Here, we introduce a cellular platform to help maintain longevity of ALS iPS-motor neurons, a cellular feature relevant for most late-onset human diseases. Long term cultures of patient-derived iPS cells might prove to be critical for the development of personalized-drugs.

Actualmente es posible modelar in vitro enfermedades neurodegenerativas humanas mediante el uso de células madre pluripotentes inducidas (iPS) derivadas del paciente. A través de ellas, es hoy concebible obtener neuronas y glía humanas, y estudiar mecanismos celulares y moleculares de enfermedades, un atributo que anteriormente no era posible para ninguna condición humana. La esclerosis lateral amiotrófica (ELA) es una de las enfermedades que se ha beneficiado con la tecnología de iPS. Al diferenciar neuronas motoras de células iPS obtenidas de pacientes con ELA, hemos iniciado estudios sobre los mecanismos que subyacen a la aparición y progresión de la enfermedad. Aquí, presentamos el desarrollo de una plataforma celular que permite extender la longevidad de las neuronas motoras derivadas de iPS, una característica relevante para la mayoría de las enfermedades humanas de inicio tardío. Los cultivos a largo plazo de células iPS provenientes de pacientes pueden ser determinantes en el desarrollo de terapias asociadas a la medicina de precisión.

Deconstructing age reprogramming

A new and simple procedure was applied to detect bisphenol A (BPA) based on a BPA aptamer and its complementarystrand (Comp. Str.). An electrode was modified with a mixture of carboxylated multiwalled carbon nanotubes and chitosan.The Comp. Str. was immobilized on a modified-glassy carbon electrode (GCE) surface via covalent binding. After theincubation of the aptamer with the electrode surface, it could interact with the Comp. Str. In the presence of BPA, itsaptamer will interact with the analyte, resulting in some changes in the configuration and leading to separation from theelectrode surface. Due to the attached ferrocene (Fc) group on the 50 head of the aptamer, the redox current of Fc hasreduced. This aptasensor can sense the level of BPA in the linear range of 0.2–2 nM, with a limit of detection of 0.38 nMand a sensitivity of 24.51 lA/nM. The proposed aptasensor showed great reliability and selectivity. The acceptable selectivity is due to the specificity of BPA binding to its aptamer. The serum sample was used as a real sample; the aptasensorwas able to effectively recover the spiked BPA amounts. It can on-site monitor the BPA in serum samples withacceptable recoveries.

Retracted: Role of LncRNA MALAT-1 on Induced Submandibular Gland Carcinoma in Albino Rats Treated with Induced Pluripotent Stem Cells (Histological and Immunhistochemical Study)

Salivary gland tumors show complex histopathology and the treatment depends mainly on the stage of cancer. Induced pluripotent stem cells (iPS) have a great role in regenerative medicine as they can generate pluripotent stem cells from any available cell types as fibroblast. Thus, the aim of this work is to investigate the possible therapeutic effect of (iPS) on induced salivary gland cancer through evaluation of the silent information regulators of sirtuin-1 (Sirt-1), Tgf-β genes and their protein expressions in addition to LncRNA MALAT-1 expression. Thirty male albino rats were employed and divided into three groups (ten rats for each group), group 1 (control): Rats were injected with phosphate buffered saline (PBS), group II induced squamous cell carcinoma (SCC): rats were injected with squamous carcinoma cells (SCC), group III (induced SCC/iPS): SCC treated rats treated with 5 × 106 iPS cells. Submandibular specimens were taken and prepared for histological, histochemical and immunohistochemical studies for Bax and TGF-β3 protein. Also, Real time PCR was performed for Sirt-1, Tgf-β, and MALAT-1 LncRNA genes expression. SIRT-1 and TGF-β protein level expression was assessed by western blot technique. Group III (iPS treated group) revealed more or less normal acinar structure with normal rearrangement of acini and normal intralobular ducts with an increase in their number. In the iPS treated group there was increasing in the amount of mucopoly saccharide in the acinar cells and intensity of BAX immunostaining while, TGF-β3 was decreased in its intensity in comparison to that of the cancer treated group. In addition to Sirt-1, Tgf-β, and MALAT-1 LncRNA expressions were increased in cancer group compared to iPS treated and control groups. Induced pluripotent stem cells play a potential therapeutic role in treatment of induced submandibular gland carcinoma. Retraction Notice: This paper has been retracted from the journal after receipt of written complains. This journal is determined to promote integrity in research publication. This retraction is in spirit of the same. After formal procedures editor(s) and publisher have retracted this paper on 19th August-2019. Related policy is available here: http://goo.gl/lI77Nn

An assessment of color effect on minimal and no-preparation veneers / 实用口腔医学杂志

Objective: To evaluate the color effect of esthetic rehabilitation of anterior teeth restored with the minimal and no-preparation veneers and to analyze the influence factors of satisfaction. Methods: 30 patients were divided into group A (9 patients with tetracycline discoloured teeth treated with 72 veneers) and group B (21 patients with non-tetracycline teeth treated with 66 veneers) . All the selected teeth were restored with the minimal and non-preparation veneers. Before the teeth were prepared and after veneers were cemented, Olympus Crystaleye was employed to obtain L*, a*, b*values of each tooth. The shade was selected according to the patients' expectation and dentist's advice. The color difference (ΔE) before and after restoration of group A and group B, the color difference (ΔE1) between the tooth color after restoration and the expectation color of the patients, the relationship of the satisfaction degree and the color difference (ΔE1), the lightness difference (ΔL*), Δa*and Δb*were analyzed by SPSS 20. 0. Results: After cemented, the color of teeth-veneer-complex obviously improved in both groups. The color difference (ΔE1) between the tooth color before and after restoration, and the expected color between the 2 group was significant (P ＜ 0. 05) . ΔE1, ΔL*, Δa*had great influence on the satisfaction of dentists and patients (P ＜ 0. 05) . Conclusion: The appearance of non-tetracycline teeth restored with the minimal and no-preparation veneers was excellent. The more of the color of the teeth-veneer-complex matched the expectation color, the higher the patients are satisfied with the restorations. The less of the lightness difference, the higher the patients are satisfied with the restorations.

Caracterización de la atención psicoterapéutica en la IPS CES Sabaneta, Colombia, 2014-2015 / Characterization of psychotherapeutic assistance in the IPS CES Sabaneta, Colombia, 2014-2015

Resumen Los cambios en la cosmovisión imperante en los últimos decenios han traído consigo sujetos con nuevas características, intereses y exigencias, que han impactado a la psicología clínica en tanto le exigen nuevas formas de comprender e intervenir las problemáticas demandadas por ellos en contextos institucionales, entre otros. De cara a estas nuevas realidades y con el fin de hacer más pertinentes las intervenciones psicoterapéuticas, se realizó una caracterización de las mismas en la Institución Prestadora de Servicios de Salud -IPS- CES Sabaneta (Colombia) durante los años 2014-201 5, a través de un análisis descriptivo de 9.140 registros de atención y 532 historias clínicas elegidas aleatoriamente. Se estudiaron aspectos sociodemográficos, administrativos y teórico-técnicos de la atención a partir de análisis de frecuencia, medidas de tendencia central, de dispersión y de forma. Se encontró que consultan tres hombres por cada mujer, siendo la población entre los 6 y 18 años la que tiene el mayor peso (59,77%). Los trastornos emocionales y del comportamiento fueron el principal diagnóstico (44,92%), seguido por los trastornos neuróticos secundarios a situaciones estresantes y somatomorfos (18,6%). Llama la atención la baja prevalencia de los trastornos de personalidad (0,56%) y que el 48,9% de los pacientes asistió a un máximo de seis sesiones. Los resultados permiten ajustar los perfiles y estrategias de atención de acuerdo con las problemáticas más prevalentes, así como los procesos administrativos y formativos relacionados con ellas.

Abstract The changes happened in the prevailing worldview in the last decades have brought subjects with new characteristics, interests and requirements, which have had an impact on the clinical psychology, as a consequence, they require from clinical psychology new ways of understanding and controlling the arisen issues that concern the institutional contexts. In order to face these realities, relevant psychotherapeutic interventions were implemented through a characterization of health attendance carried out in IPS CES Saba-neta during 2014-201 5, conducted by a descriptive analysis of 9140 records of assistance and an analysis of 532 clinical records, chosen randomly. Sociodemographic, administrative and theoretical-technical aspects of the care service were studied based on frequency analysis, measures of central tendency and dispersion using the SPSS software. It was found that 3 men in 1 woman attend to medical service, being the population between ages of 6 and 18 the one that present the highest weight (59, 77 %). Emotional and behavioral disorders were the main diagnosis (44.92%), followed by neurotic disorders secondary to stressful and somatomorphic situations (18.6%). It is noticed the low prevalence of personality disorders (0.56%) even though 48.9% of patients attended a maximum of six sessions. The results allow adjusting the profiles and care service strategies according to the most prevalent problems, as well as the administrative and formative processes that involve these issues.

Alternativas de tratamientos de superficie para adhesión de cerámica de disilicado de litio / Alternatives of surface treatments for adhesion of lithium disilicate ceramics

Introduction: the clinical success of a restoration is strongly associated with the quality and durability of the ceramic-cement resin interface. In order to obtain an adequate union between these materials of different nature surface treatments are used and achieve mechanical retention or chemical interaction. Objectives: to check if any method promotes a true chemical bond between lithium disilicate ceramics and resin cement. As well as determineif there is any treatment that reports bonding values comparable to hydrofluoric acid and silane (gold standard). Methods: a systematic literature review was developed based on the PRISMA strategy, where the databases were searched: Science Direct, Pubmed (MEDLINE), EMBASE, Springer Journal, SciELO with MeSH and free terms from 2005 to November 2016 for articles in English and Spanish on surface treatments for lithium disilicate. Results: from 58 publications selected a sample of 21 articles. Two articles reported high risk of bias. Conclusions: hydrofluoric acid and silane continue to be the method with the highest and most reliable adhesion values in the literature. Universal adhesives are an alternative to promote chemical adhesion additional to the silane. Diamond burs, Nd: YAG and Er: YAG laser are not recommended as surface treatments(AU)

Introducción: el éxito clínico de una restauración se asocia fuertemente a la calidad y duración de la interface cerámica-cemento resinoso. Para que exista una adecuada unión entre estos materiales de distinta naturaleza se emplean tratamientos de superficie para lograr una buena retención mecánica o interacción química. Objetivos: revisar si algún método promueve una verdadera adhesión química entre la cerámica de disilicato de litio y el cemento resinoso, así como determinar si existe algún tratamiento que reporte valores de unión comparables al ácido fluorhídrico y silano (patrón de oro). Métodos: se desarrolló una revisión sistemática de literatura basada en la estrategia PRISMA, donde se buscó en las bases de datos: Science Direct, Pubmed (MEDLINE), EMBASE, Springer Journal, SciELO con términos MeSH y libres desde el 2005 a noviembre de 2016 para artículos en inglés y español sobre tratamientos de superficie para disilicato de litio. Resultados: de 58 publicaciones, se seleccionó una muestra de 21 artículos. Dos artículos reportaron riesgo de sesgo alto. Conclusiones: el ácido fluorhídrico y silano continúan siendo el método con los valores de adhesión más altos y confiables de la literatura. Los adhesivos universales son una alternativa para promover adhesión química adicional al silano. Fresas diamantadas, laser Nd: YAG y Er:YAG no se recomienda como tratamientos de superficie(AU)

The effect of Er: YAG laser irradiation on bonding properties of IPS e.max CAD ceramics / 口腔疾病防治

Objective@#To investigate different Er:YAG laser power settings on the bonding properties of IPS e.max CAD ceramics. @*Methods @# 96 IPS e.max CAD ceramics blocks (5 mm × 5 mm × 5 mm) were prepared and randomly divided into 8 groups (n = 12), the untreated blocks served as the control, while one of the experimental groups was treated with 4.5% HF for 20 seconds, six remaining test group (C、D、E、F、G、H) were treated with different Er: YAG laser power settings: 100 mJ、200 mJ、300 mJ、400 mJ、500 mJ and 600 mJ. Morphology of the ceramic surface was observed by atomic force microscopy and its shear bond strength (SBS) was tested. @*Results @#Higher shear bond strength values were found in group C-H compared to group B, the highest is group F (24.12 ± 1.91) MPa. The difference was statistically significant. The atomic force microscope observation of the surface structure showed that the control group was smooth and flat, and the HF-like etching group formed a uniform needle-like convex structure. The laser group gradually formed a regularly arranged cylindrical convex structure, in which the surface of the G and H groups was damaged. @*Conclusion@# The Er: YAG laser power settings of 400 mJ can be used as an effective pretreatment method before bonding of IPS e.max CAD ceramic.

Clinical effects of full crown prosthesis on anterior teeth / 中华医学美学美容杂志

Objective To evaluate the clinical effects of anterior teeth repair of three different restorations made of Co-Cr alloy,Ag-Pd alloy and all-ceramic crowns.Methods 90 cases who needed the both maxillary and mandibular anterior teeth restarations were selected and treated respectively with Co-Cr alloy porcelain fused to metal crowns (PFM)(60 teeth),Ag-Pd alloy PFM (46 teeth)and IPS e.max Press Porcelain full crown (38 teeth).Gingival index was observed before restoration and in 6 and 12 months after restoration.Meanwhile,clinical indicators of two restorations were evaluated as cervical margin's coloration,margin fitness degree,color of restorations,fracture of restorations and contour of restorations,etc.Results The healthy condition of gingiva in groups of Ag-Pd alloy PFM and IPS e.max Press Porcelain full crown were superior to the group of Co-Cr alloy PFM (P＜0.05).There was no cervical margin's coloration in groug of all-ceramic PFM.The color and contour of this group was superior to the group of Co-Cr alloy PFM (P ＜0.05).The significant difference between group of Co Cr alloy and group of Ag-Pd alloy was cervical margin's coloration and marginal density of the restoration (P＜0.05).Conclusions The clinical effects of both groups of Ag-Pd alloy PFM and IPS e.max Press Porcelain full crown is superior to the group of Co-Cr alloy PFM.The IPS e.max Press Porcelain full crown group works best.

Effect of different hydrofluoric acid etching methods on the surface and adhesion strength of two ceramic inlays / 口腔疾病防治

Objective@#o study the effect of cleaning treatment with hydrofluoric acid (HF) on the surface and bonding strength of IPS e.max and Vita Mark II ceramic inlays. @*Methods@#Fifty pieces of IPS e.max and Vita Mark II ceramic inlay specimens were made separately using CAD/CAM. After uniformly bonding surfaces using 9% HF etching, they were randomly divided into an untreated control group (group A) and the following experimental groups: neutralizing powder (B group), 37% phosphoric acid (group C), ultrasonic cleaning (group D) and neutralizing powder + 37% phosphoric acid + ultrasonic cleaning (group E). Each set of 8 specimens was bonded to Variolink N resin adhesive under standard conditions. The shear adhesive strength was measured after exposure to a constant-temperature water bath at 37 ℃ for 24 h. The location of the fracture and the type of adhesion failure were recorded. The shear adhesion and the average strength of the connection were analyzed. The remaining 2 specimens were used for scanning electron microscopy (SEM) to observe the surface morphology, including the crystal structure, pore pattern, and residue.@*Results @# The results were similar for the IPS e.max and Vita Mark II inlays. The maximum bond strength was observed in the IPS e.max ceramic inlays in group E, with an average bond strength 11.96 MPa higher than that in group A. Among the Vita Mark II porcelain inlays, the maximum bond strength was observed in group E. The average bond strength was 9.74 MPa higher than that in group A. The results of the statistical analysis were similar for the IPS e.max and Vita Mark II porcelain inlays, with significant differences in the bond strengths between groups C, D, and E and the control group (P < 0.05). There was no significant difference in the adhesive strength between groups B and A. At the same time, there was no significant difference in the bond strength between the treatment groups B, C, D, and E (P > 0.05). SEM revealed that the pores on the surface of ceramics subjected to the acid etching treatment were broadened and uniform, with less residue than observed in the control group. The effects of treatments D and E were the best. @*Conclusion@#The HF etching treatment can enhance the bonding strength of IPS e.max and Vita Mark Ⅱ ceramic inlays while leaving little residue, and the joint strength is highest when the joints are treated together.

The effect of Er: YAG laser irradiation on bonding properties of IPS e.max CAD ceramics / 口腔疾病防治

Objective @#To investigate different Er:YAG laser power settings on the bonding properties of IPS e.max CAD ceramics. @*Methods@# 96 IPS e.max CAD ceramics blocks (5 mm × 5 mm × 5 mm) were prepared and randomly divided into 8 groups (n = 12), the untreated blocks served as the control, while one of the experimental groups was treated with 4.5% HF for 20 seconds, six remaining test group (C、D、E、F、G、H) were treated with different Er: YAG laser power settings: 100 mJ、200 mJ、300 mJ、400 mJ、500 mJ and 600 mJ. Morphology of the ceramic surface was observed by atomic force microscopy and its shear bond strength (SBS) was tested. @*Results @#Higher shear bond strength values were found in group C-H compared to group B, the highest is group F (24.12 ± 1.91) MPa. The difference was statistically significant. The atomic force microscope observation of the surface structure showed that the control group was smooth and flat, and the HF-like etching group formed a uniform needle-like convex structure. The laser group gradually formed a regularly arranged cylindrical convex structure, in which the surface of the G and H groups was damaged. @*Conclusion @#The Er: YAG laser power settings of 400 mJ can be used as an effective pretreatment method before bonding of IPS e.max CAD ceramic.

Research progress on RLRs in the treatment of multiple sclerosis / 天津医药

At present, the etiology and pathogenesis of multiple sclerosis are unclear. RIG-Ⅰ-like receptors are a new-ly discovered pattern recognition receptors (RLRs), which are located in cytoplasm. They can recognize the helicase of viral dsRNAs, and interact with interferon beta promoter stimulator (IPS)-1 through their caspase activation recruitment domain (CARD), then form IPS-1 signalsome and induce the expression of interferon typeⅠ(Ⅰ-IFN), thereby initiate innate im-mune response and induce antiviral response. Recent studies have found that mice lacking IPS-1 would develop exacerbated disease and accompanied by markedly higher inflammation, increasing axonal damage and demyelination. Furthermore, initi-ating the RIG-Ⅰ-like helicase receptor on the immune cells can alleviate inflammation and myelin fracture in multiple scle-rosis of mouse model, thus limit the incidence of paralysis. This paper is a review about the research progress on RLRs in the treatment of multiple sclerosis.

Induced Pluripotent Stem (iPS) Cells in Dentistry: A Review

iPS cells are derived from somatic cells via transduction and expression of selective transcription factors. Both viral-integrating (like retroviral) and non-integrating (like, mRNA or protein-based) techniques are available for the production of iPS cells. In the field of dentistry, iPS cells have been derived from stem cells of apical papilla, dental pulp stem cells, and stem cells from exfoliated deciduous teeth, gingival and periodontal ligament fibroblasts, and buccal mucosa fibroblasts. iPS cells have the potential to differentiate into all derivatives of the 3 primary germ layers i.e. ectoderm, endoderm, and mesoderm. They are autogeneically accessible, and can produce patient-specific or disease-specific cell lines without the issue of ethical controversy. They have been successfully tested to produce mesenchymal stem cells-like cells, neural crest-like cells, ameloblasts-like cells, odontoblasts-like cells, and osteoprogenitor cells. These cells can aid in regeneration of periodontal ligament, alveolar bone, cementum, dentin-pulp complex, as well as possible Biotooth formation. However certain key issues like, epigenetic memory of iPS cells, viral-transduction, tumorgenesis and teratoma formation need to be overcome, before they can be successfully used in clinical practice. The article discusses the sources, pros and cons, and current applications of iPS cells in dentistry with an emphasis on encountered challenges and their solutions.

Estudio de opinión sobre preferencias de los pacientes en la escogencia entre la medicina tradicional y alternativa en la ciudad de Barranquilla / Opinion study on patient preferences in the choice between traditional and alternative medicine in the city of Barranquilla

El propósito de este artículo es determinar las diferentes opiniones que se exponen, objeto de este análisis, como es la preferencia del paciente a la hora de escoger entre un médico alternativo y un médico alopático en la ciudad de Barranquilla. Para este proceso se decidió aplicar una investigación cuantitativa donde el instrumento de evaluación son varios tipos de encuestas de profundidad a usuarios, médicos y farmacias; donde se evalúa en una muestra de individuos y sector de una población. Su finalidad es obtener la información y analizarla para su mejor comprensión, de manera que pueda utilizarse eficazmente para conocer la opinión de las personas a la hora de elegir entre la medicina tradicional llamada también alopática y la alternativa denominada natural, para la consecución del artículo.