RÉSUMÉ
Objective@#To better understand the significance of the pressure-time curve and flow-time curve from the perspective of PB840 ventilator working principle.@*Methods@#① Mechanical principle: flow supply valves (air valve and oxygen valve) and exhalation valve in PB840 ventilator were controlled to achieve the ventilation target (volume or pressure) by the central processing unit according to the monitoring data from pressure sensors (P1 at the supply side, P2 at the exhalation side) and flow sensors (Q1 at the air side, Q2 at the oxygen side, Q3 at the exhalation side). ② The essence of curve: each point means a value of pressure or flow at a certain time measured by the sensors or calculated by the system. ③ The respiratory process could be divided into inspiratory part, expiratory part, and the connection part from expiratory to inspiratory. The air running state and the respiratory mechanics relationship at the three parts could be inferred according to the form of curves.@*Results@#① Inspiratory process: at volume-controlled and constant flow ventilation: there should be a relationship "Pc-Pa = XR" between alveolar pressure (Pa) and circuit pressure (Pc) according to Ohm law. So, the Pc curve (pressure-time curve) could indirectly reflect the Pa curve with the flow (X) and resistance (R) being constant. At pressure-set ventilation: it is the goal of ventilator to maintain the Pc at the target level. So, the stability of the target pressure line in pressure-time curve reflects the matching ability of the flow supply valves and the exhalation valve. ② Expiratory process: it could be divided into pre-expiratory [without basic flow (Ba) or bias flow (Bi)] and post-expiratory (with Ba or Bi), where Ba or Bi is equal to "Q1+Q2". So, the mathematical function are "X(t) = Q3t" in pre-part, and "X(t) = Q3t-(Q1t+Q2t)" in post-part. The relationship between pressure and flow at peak expiratory flow point: it could be found that there is an obvious time span and area formation under the curve from 0 to peak point (Fpeak) after stretching the abscissa axis of flow-time curve. It means that some gas have been discharged from the lung when it arrives at the peak point. So, the alveolar pressure should be lower than the platform pressure at the point (Pplat). The circuit pressure is significantly higher than positive end expiratory pressure (PEEP) at the point in the stretching axis diagram. So, it means that the formula "RE = (Pplat-PEEP)/Fpeak" to calculate the expiratory resistance (RE) is unreasonable in the angle of Ohm law. ③ The process from exhalation to inspiratory: according to the difference of the starting point of the conversion, it could be divided into two cases: one is that the inspiratory started from the ending of exhalation. Here, the inhaling starting point is lying in the abscissa axis. The other is that the inspiratory started before the ending of exhalation (with endogenous positive end expiratory pressure). Here, the starting point is lying below the abscissa axis, and the slope of the following curve is obviously larger than the slope of natural expiratory curve. According to the difference of results from the starting point to the end of the inhalation triggering effort, it could be divided into two cases: one is that it reach the trigger point. Here, the expiratory curve extends upward from or below the horizontal axis until an effective air supply is triggered. The other is that it could not reach the trigger point. Here, the expiratory curve extends upward from or below the horizontal axis, but then runs downward (meaning exhaling).@*Conclusion@#It is helpful to analyze the ventilation state, ventilation failure, and the causes of man-machine confrontation with understanding the ventilation principle and the air route map of the ventilator.
RÉSUMÉ
Objective To better understand the significance of the pressure-time curve and flow-time curve from the perspective of PB840 ventilator working principle. Methods ① Mechanical principle: flow supply valves (air valve and oxygen valve) and exhalation valve in PB840 ventilator were controlled to achieve the ventilation target (volume or pressure) by the central processing unit according to the monitoring data from pressure sensors (P1 at the supply side, P2 at the exhalation side) and flow sensors (Q1 at the air side, Q2 at the oxygen side, Q3 at the exhalation side). ② The essence of curve: each point means a value of pressure or flow at a certain time measured by the sensors or calculated by the system. ③ The respiratory process could be divided into inspiratory part, expiratory part, and the connection part from expiratory to inspiratory. The air running state and the respiratory mechanics relationship at the three parts could be inferred according to the form of curves. Results ① Inspiratory process: at volume-controlled and constant flow ventilation: there should be a relationship "Pc-Pa = XR" between alveolar pressure (Pa) and circuit pressure (Pc) according to Ohm law. So, the Pc curve (pressure-time curve) could indirectly reflect the Pa curve with the flow (X) and resistance (R) being constant. At pressure-set ventilation: it is the goal of ventilator to maintain the Pc at the target level. So, the stability of the target pressure line in pressure-time curve reflects the matching ability of the flow supply valves and the exhalation valve. ② Expiratory process: it could be divided into pre-expiratory [without basicflow (Ba) or bias flow (Bi)] and post-expiratory (with Ba or Bi), where Ba or Bi is equal to "Q1+Q2". So, the mathematical function are "X(t) = Q3t" in pre-part, and "X(t) = Q3t-(Q1t+Q2t)" in post-part. The relationship between pressure and flow at peak expiratory flow point: it could be found that there is an obvious time span and area formation under the curve from 0 to peak point (Fpeak) after stretching the abscissa axis of flow-time curve. It means that some gas have been discharged from the lung when it arrives at the peak point. So, the alveolar pressure should be lower than the platform pressure at the point (Pplat). The circuit pressure is significantly higher than positive end expiratory pressure (PEEP) at the point in the stretching axis diagram. So, it means that the formula "RE = (Pplat-PEEP)/Fpeak" to calculate the expiratory resistance (RE) is unreasonable in the angle of Ohm law. ③ The process from exhalation to inspiratory: according to the difference of the starting point of the conversion, it could be divided into two cases: one is that the inspiratory started from the ending of exhalation. Here, the inhaling starting point is lying in the abscissa axis. The other is that the inspiratory started before the ending of exhalation (with endogenous positive end expiratory pressure). Here, the starting point is lying below the abscissa axis, and the slope of the following curve is obviously larger than the slope of natural expiratory curve. According to the difference of results from the starting point to the end of the inhalation triggering effort, it could be divided into two cases: one is that it reach the trigger point. Here, the expiratory curve extends upward from or below the horizontal axis until an effective air supply is triggered. The other is that it could not reach the trigger point. Here, the expiratory curve extends upward from or below the horizontal axis, but then runs downward (meaning exhaling). Conclusion It is helpful to analyze the ventilation state, ventilation failure, and the causes of man-machine confrontation with understanding the ventilation principle and the air route map of the ventilator.