Résumé
Objective The ionization chamber of ELEKTA medical linear accelerator monitoring is open to environmental factors such as temperature, air pressure, and humidity that may affect the stability of absolute dose output .The article aimed to ana-lyze the morning and evening absolute dose output stability at different energies of ELEKTA SYNERGY medical linear accelerator . Methods The absolute doses at different energies of medical linear accelerators were calibrated according to the IAEA TRS -277 re-port, and WI3 type solid water was used to perform repeated measurements in the morning and in the evening for 52 consecutive days under the same measurement conditions , during which a water tank measurement was conducted at random intervals per week to verify the accuracy of WI3 solid water measurements. Results The maximum deviation of WI3 solids water and tank measurement at all en -ergies was 0.5％ and the maximum deviations of daily energy stability at different energies were : -2.0％ (6MV), 1.9％ (15MV), 1.8％ (6MeV), -2.4％ (8MeV), -2.3％ (10MeV), -2.0％ (12MeV), 2.1％ (15MeV).The differences of 6MV, 15MV, 8MeV, and 10MeV energies in morning and evening paired t tests were statistically significant (P<0.05) without clinical significance, while no statistic significance was found in the differences of 6MeV, 12MeV, and 15MeV energies ( P >0.05). Conclusion Elekta Synergy medical linear accelerator shows excellent stability in absolute dose output.
Résumé
Objective To explore the Monte Carlo calculation methods for the absolute dose calibration and output factor of 6 MV flattening-filter ( FF) and flattening-filter free ( FFF) photon beams based on TrueBeam accelerator .Methods The BEAMnrc code was used to model the LINAC head of FF and FFF modes.The BEAM_up covers the components from the target to the monitor chamber , and BEAM_down includes the structures beneath the chamber , the dose deposit to the monitor chamber contributed by the incidence electrons and scattered particles from the secondary collimators were calculated respectively .The incidence electron-induced dose at certain depths on the central axis were simulated by means of the DOSXYZnrc code .By means of dose calibration equation , the calibration factor for the standard field (10 cm ×10 cm) and the output factors for various fields (1 cm ×1 cm-40 cm ×40 cm) were computed respectively .Results For the 6 MV FF and FFF beams under the standard 10 cm ×10 cm field, 1 MU equals to 7.747 ×1013 ±3.099 ×1011 and 3.248 ×1013 ±1.624 ×1011 electrons to the target , respectively , which deposited 21.53 and 35.01 cGy to the monitor chamber of the virtual accelerator respectively .The difference between the simulated and calculated output factors were 0.72%±1.4%and 0.56%±0.78%for FF and FFF , respectively .Conclusions The model generated and measured output factors agree well , indicating the good accuracy of the dose calculation by the model , which would provides basis for further clinical dosimetric studies .
Résumé
Objective To study the relationship between parameter settings in the intensity-modulated radiation therapy (IMRT) planning in order to explore the effect of parameters on absolute dose verification.Methods Forty-three esophageal carcinoma cases were optimized with Pinnacle 7.6c by experienced physicist using appropriate optimization parameters and dose constraints with a number of iterations to meet the clinical acceptance criteria.The plans were copied to water-phantem,0.13 cc ion Farmer chamber and DOSE1 dosimeter was used to measure the absolute dose.The statistical data of the parameters of beams for the 43 cases were collected,and the relationships among them were analyzed.The statistical data of the dosimetry error were collected,and comparative analysis was made for the relation between the parameters of beams and ion chamber absolute dose verification results.Results The parameters of beams were correlated among each other.Obvious affiliation existed between the dose accuracy and parameter settings.When the beam segment number of IMRT plan was more than 80,the dose deviation would be greater than 3％ ; however,if the beam segment number was less than 80,the dose deviation was smaller than 3％.When the beam segment number was more than 100,part of the dose deviation of this plan was greater than 4％.On the contrary,if the beam segment number was less than 100,the dose deviation was smaller than 4％ definitely.Conclusions In order to decrease the absolute dose verification error,less beam angles and less beam segments are needed and the beam segment number should be controlled within the range of 80.
Résumé
OBJECTIVE: The authors developed a stereotactic device for irradiation of small animals with Leksell Gamma Knife(R) Model C. Development and verification procedures were described in this article. METHODS: The device was designed to satisfy three requirements. The mechanical accuracy in positioning was to be managed within 0.5 mm. The strength of the device and structure were to be compromised to provide enough strength to hold a small animal during irradiation and to interfere the gamma ray beam as little as possible. The device was to be used in combination with the Leksell G-frame(R) and KOPF(R) rat adaptor. The irradiation point was determined by separate imaging sequences such as plain X-ray images. RESULTS: The absolute dose rate with the device in a Leksell Gamma Knife was 3.7% less than the value calculated from Leksell Gamma Plan(R). The dose distributions measured with GAFCHROMIC(R) MD-55 film corresponded to those of Leksell Gamma Plan(R) within acceptable range. The device was used in a series of rat experiments with a 4 mm helmet of Leksell Gamma Knife. CONCLUSION: A stereotactic device for irradiation of small animals with Leksell Gamma Knife Model C has been developed so that it fulfilled above requirements. Absorbed dose and dose distribution at the center of a Gamma Knife helmet are in acceptable ranges. The device provides enough accuracy for stereotactic irradiation with acceptable practicality.
Sujets)
Animaux , Rats , Rayons gamma , Dispositifs de protection de la têteRésumé
PURPOSE: The purpose of this study was to evaluate whether a GafChromic film applied to stereotactic radiosurgery with a linear accelerator could provide information on the value for acceptance testing and quality control on the absolute dose and relative dose measurements and/or calculation of treatment planning system. MATERIALS AND METHODS: A spherical acrylic phantom, simulating a patient's head, was constructed from three points. The absolute and relative dose distributions could be measured by inserting a GafChromic film into the phantom. We tested the use of a calibrated GafChromic film (MD-55-2, Nuclear Associate, USA) for measuring the optical density. These measurements were achieved by irradiating the films with a dose of 0-112 Gy employing 6 MV photon. To verify the accuracy of the prescribed dose delivery to a target isocenter using a five arc beams (irradiated in 3 Gy per one beam) setup, calculated by the Linapel planning system the absolute dose and relative dose distribution using a GafChromic film were measured. All the irradiated films were digitized with a Lumiscan 75 laser digitizer and processed with the RIT113 film dosimetry system. RESULTS: We verified the linearity of the Optical Density of a MD-55-2 GafChromic film, and measured the depth dose profile of the beam. The absolute dose delivered to the target was close to the prescribed dose of Linapel within an accuracy for the GafChromic film dosimetry (of +/- 3%), with a measurement uncertainty of +/- 1 mm for the 50~90% isodose lines. CONCLUSION: Our results have shown that the absolute dose and relative dose distribution curves obtained from a GafChromic film can provide information on the value for acceptance. To conclude the GafChromic film is a convenient and useful dosimetry tool for linac based radiosurgery.