Résumé
Objective@#To compare the efficiency and biocompatibility of four different silanes on immobilizing c(RGDfK) peptide on titanium surface.@*Methods @# After alkali-heat treatment (group OH), the titanium surface was treated with 3-aminopropyltriethoxysilane (APTES) (group OHAP), 3-chloropropyltriethoxysilane (CPTES) (group OHCP) (3-mercaptopropyltrimethoxysilane (MPTS) (group OHMPT) and 3-isobutyryloxy propyltrimethoxysilane(γ- MPS) (group OHMPS) to immobilize the c(RGDfK) cyclic peptide and constructa titanium-silane-c(RGDfK) coating. The NT group was the blank control group. The surface morphology and wettability of the coatings were detected using scanning electron microscopy and contact angle measurement. The elemental composition of the titanium surface was analyzed using X-ray photoelectron spectroscopy. After fluorescent staining with 4’,6-diamino-2-phenylindole (DAPI) and phalloidin, the adhesion of mouse preosteoblast MC3T3-E1 cells on the surface of the materials was observed using laser confocal microscopy. Cell counting kit-8 (CCK-8) and alkaline phosphatase (ALP) activity assays were used to evaluate the proliferation and osteogenic differentiation of MC3T3-E1 cells on the surface of the materials, respectively. @*Results @#Scanning electron microscope observation showed a spongy-like 3-dimensional network formed on the titanium surface after alkali-heat treatment with silane-c(RGDfK) coating adhesion. The wettability of each group was greatly improved compared to the untreated titanium surface. The element ratios of Si/Ti and amide-N/Ti in the OHMPS group were the highest. The OHAP group exhibited the best cell adhesion effect. The cell proliferation and ALP activity of the OHAP, OHMPT, and OHMPS groups were significantly higher than the control group (P <0.05); there was no statistical difference between the OHCP group and the control group.@*Conclusion @#MPTS, CPTES and γ-MPS covalently immobilized cyclic peptide c(RGDfK) on the titanium surface, which promoted adhesion, proliferation and osteogenic differentiation of MC3T3-E1 cells. Theγ-MPS conjugated C (RGDfK)cyclic peptide exhibited the best effect. MPTS, CPTES and γ-MPS coupled with c(RGDfK) cyclic peptides had similar biological properties.
Résumé
PURPOSE: Ti-6Al-4V alloy is widely used as an implant material because of its good biocompatibility and good mechanical property compared with commercial pure titanium. Otherwise, toxicity of aluminum and vanadium in vivo has been reported. Ti-8Ta-3Nb alloy is recently developed in the R&D Center for Ti and Special Alloys and it was reported that this alloy has high mechanical strength, no cytotoxicity and similar biocompatibility to commercial pure titanium, but many studies are needed for its clinical use. In these experiment, we carried out different surface treatment on each Ti-8Ta-3Nb alloy disks, then cultured cell on it and assessed biological response. MATERIALS AND METHODS: cpTi, Ti-6Al-4V, Ti-8Ta-3Nb alloy disks were prepared and carried out sandblasting and acid etching (SLA) or alkali-heat treatment (AH) on the Ti-8Ta-3Nb alloy disks. We cultured primary rat calvarial cells on each surface and assessed early cell attachment and proliferation by scanning electron microscopy, cell proliferation, alkaline phosphatase activity. RESULT: The rates of cell proliferation on the cpTi, Ti-8Ta-3Nb AH disks were higher than others (p<0.05) and alkaline phosphatase activity was significantly enhanced on the Ti-8Ta-3Nb AH disks (p<0.05). CONCLUSION: Most favorable cell response was shown on the Ti-8Ta-3Nb AH surfaces. It is supposed that alkali-heat treatment of the Ti-8Ta-3Nb alloy could be induced earlier bone healing and osseointegration than smooth surface.