Determination of Shear Bond Strength of Nanocomposite to Porcelain and Metal Alloy

Abstract Objective: To compare porcelain and metal repair done with both nanocomposite and conventional composite. Material and Methods: A total of 30 cylinders were fabricated from Porcelain (I), Porcelain fused to metal (II), and metal (III) substrate each. Control group (A) was bonded with conventional micro-hybrid composite and experimental group (B) was bonded with nanocomposite in a 2 mm thickness. All specimens were thermocycled and stored in distilled water at 37 °C for 7 days. A universal testing machine was used to measure the Shear bond strength (SBS). The difference between bond strengths of the groups was compared using an independent t-test. Results: In all three groups, the SBS was higher in the experimental group as compared to the control group. The use of nanocomposite of metal alloy presented maximum shear bond strength, followed by samples of porcelain fused to metal and finally porcelain, showing the lowest values of SBS. Conclusion: Porcelain and alloys bonded with nanocomposite exhibit enhanced adhesiveness as well as aesthetic and mechanical properties. This subsequently would translate into providing higher clinical serviceability and durability and hence a cost-effective and accessible repair option for human welfare (AU).

A novel application of nano eggshell/titanium dioxide composite on occluding dentine tubules: an in vitro study

Abstract To synthesize Nano eggshell-titanium-dioxide (EB@TiO2) biocomposite and to evaluate its effectiveness in occluding opened dentine tubules. EB@TiO2 was synthesized and characterized using X-ray diffraction (XRD), and Transmission Electron Microscope (TEM). Sixteen simulated bovine dentine discs were prepared and randomly assigned into four groups according to the following treatment (n = 4): Group 1: No treatment; Group 2: eggshell powder; Group 3: EB@TiO2; Group 4: Sensodyne. These were then agitated in a solution of 1g powder and 40mL water for 3hours. Thereafter, each dentine discs from the respective groups were post-treated for 5 min with 2wt% citric acid to test their acid resistant characteristics. Scanning Electron Microscope (SEM) was used to observe the effectiveness of occluded dentine pre-and post-treatment. The cytotoxicity of the synthesized EB@TiO2 was tested using NIH 3T3 assay. ANOVA was used to evaluate the mean values of the occluded area ratio and the data of MTS assay. This was followed by a multi-comparison test with Bonferroni correction (α = .05). The XRD confirmed that EB@TiO2 was successfully modified through ball-milling. The TEM revealed the presence of both spherical and irregular particle shape powders. The SEM result showed that EB@TiO2 could effectively occlude open dentine tubules. Equally, the result demonstrated that EB@TiO2 exhibited the highest acid resistant stability post-treatment. NIH 3T3 assay identified that EB@TiO2 had little effect on the NIH 3T3 cell line even at the highest concentration of 100µg/ml. This study suggests that the application of EB@TiO2 effectively occluded dentine tubules and the occlusion showed a high acid resistant stability.

Inhibitory effect of reduced graphene oxide-silver nanocomposite on progression of artificial enamel caries

Abstract The use of antimicrobial agents is an efficient method to prevent dental caries. Also, nanometric antibacterial agents with wide antibacterial spectrum and strong antibacterial effects can be applied for prevention of dental caries. Objectives: The aim of this study was to evaluate the inhibitory effect of reduced graphene oxide-silver nanoparticles (rGO/Ag) composite on the progression of artificial enamel caries in a Streptococcus mutans biofilm model. Material and Methods: Enamel specimens from bovine incisors were divided into eight treatment groups (n = 13), as follows: group 1 was inoculated with S. mutans grown in Brain Heart Infusion containing 1% sucrose (1% BHIS), as negative control; groups 2-4 were inoculated with S. mutans grown in the presence of different rGO/Ag concentrations (0.08, 0.12, 0.16 mg/mL) + 1% BHIS; group 5-7 were inoculated with S. mutans grown in the presence of different agents (0.16 mg/mL reduced graphene oxide, 0.16 mg/mL silver nanoparticles, 10 ppm NaF) + 1% BHIS; group 8 was mixed with 1% BHIS, without inoculation. Artificial enamel carious lesions were produced by S. mutans biofilm model for 7 days. Confocal laser scanning microscopy and atomic force microscopy were used to analyze roughness and morphology of the enamel surface. Polarized light microscopy and confocal laser scanning microscopy were employed to measure the lesion depth and the relative optical density (ROD) of the demineralized layer. Results: Compared with the control groups, the rGO/Ag groups showed: (a) reduced enamel surface roughness; (b) much smoother and less eroded surfaces; (c) shallower lesion depth and less mineral loss. Conclusion: As a novel composite material, rGO/Ag can be a promising antibacterial agent for caries prevention.

Surface, thermal and hemocompatible properties of novel single stage electrospun nanocomposites comprising polyurethane blended with bio oilTM

ABSTRACT In this work, the physicochemical and blood compatibility properties of prepared PU/Bio oil nanocomposites were investigated. Scanning electron microscope (SEM) studies revealed the reduction of mean fiber diameter (709 ± 211 nm) compared to the pristine PU (969 nm ± 217 nm). Fourier transform infrared spectroscopy (FTIR) analysis exposed the characteristic peaks of pristine PU. Composite peak intensities were decreased insinuating the interaction of the bio oilTM with the PU. Contact angle analysis portrayed the hydrophobic nature of the fabricated patch compared to pristine PU. Thermal gravimetric analysis (TGA) depicted the better thermal stability of the novel nanocomposite patch and its different thermal behavior in contrast with the pristine PU. Atomic force microscopy (AFM) analysis revealed the increase in the surface roughness of the composite patch. Activated partial thromboplastin time (APTT) and prothrombin time (PT) signified the novel nanocomposite patch ability in reducing the thrombogenicity and promoting the anticoagulant nature. Finally the hemolytic percentage of the fabricated composite was in the acceptable range revealing its safety and compatibility with the red blood cells. To reinstate, the fabricated patch renders promising physicochemical and blood compatible nature making it a new putative candidate for wound healing application.

O trabalho no cárcere: reflexões acerca da saúde do agente penitenciário / El trabajo en la prisión: reflexiones sobre la salud del guardia penitenciário / The work in prison: reflections on the health of prison officers

RESUMO Objetivo: conhecer as condições de trabalho de agentes penitenciários e os reflexos do exercício da atividade laboral em sua saúde. Método: pesquisa descritiva, qualitativa. Os dados foram coletados por meio de entrevista aberta com agentes de um presídio regional e submetidos a análise de conteúdo na modalidade temática. Resultados: os resultados revelaram condições de trabalho insatisfatórias por deficiência de recursos materiais e descaso do poder público com as questões inerentes à ressocialização do apenado, resultando em exposição aos riscos psicossociais, insatisfação e desgaste emocional dos trabalhadores. Conclusão: investimentos na segurança dos trabalhadores podem contribuir para a promoção de sua saúde. .

RESUMEN Objetivo: conocer las condiciones laborales de guardias de prisión y las consecuencias del ejercicio de la actividad laboral en su salud. Método: investigación cualitativa y descriptiva. Los datos fueron recolectados a través de entrevistas abiertas con agentes de una cárcel regional y se sometieron a análisis de contenido en la modalidad temática. Resultados: los resultados mostraron condiciones insatisfactorias por la falta de recursos materiales y el abandono por parte del gobierno en los asuntos relacionados con la rehabilitación del condenado, lo que resulta en la exposición a riesgos psicosociales, la insatisfacción y el agotamiento emocional de los trabajadores. Conclusión: las inversiones en la seguridad de los trabajadores pueden contribuir a la promoción de su salud. .

ABSTRACT Objective: to understand the working conditions of prison offi cers and the repercutions of labor activity on their health. Method: qualitative and descriptive research. Data were collected through open interviews with the prison offi cers of a regional prision and the speeches were submitted to content analysis. Results: the results showed unsatisfactory working conditions due to poor material resources and neglect of governmental regarding rehabilitation of convicts, resulting in workers’ exposure to psychosocial risks, dissatisfaction, and emotional distress. Conclusion: investments on the security of workers may contribute to their health promotion. .

Completeness of tuberculosis reporting forms for disease control in individuals with HIV/AIDS in priority cities of Bahia state / Completude das fichas de notificação de Tuberculose nos municípios prioritários da Bahia para controle da doença em indivíduos com HIV/AIDS

The control of HIV / Tuberculosis (TB) co -infection remains a challenge for public health. Notification is mandatory for both diseases and the National Case Registry Database (Sinan) is responsible for the collection and processing of individual forms of reporting and monitoring. The adequate fulfillment of these fields chips (completeness) is essential to follow the dynamics of the disease and set priorities for intervention. The aim of this study was to evaluate the completeness of the notification forms of tuberculosis in the priority municipalities of Bahia (Camaçari , Feira de Santana , Ilhéus , Itabuna, Jequié, Lauro de Freitas , Porto Seguro , Teixeira de Freitas , Paulo Afonso, Barreiras and Salvador) to control the disease in individuals with HIV/AIDS using tabulations obtained from the Sinan in the period from 2001 to 2010. The results showed that despite the completeness of the field HIV be above 50 %, more than half the cases were met as "undone" or "being processed" in all municipalities assessed in the period. The low completeness of reporting forms may compromise the quality of surveillance of TB cases. The results suggest the need for greater availability of HIV testing in these individuals.

O controle da coinfecção HIV/Tuberculose (TB) ainda representa um desafio para a saúde pública. Ambas as doenças são de notificação obrigatória e o Sistema Nacional de Agravos de Notificação (SINAN) é o órgão responsável pela coleta e processamento das fichas individuais de notificação e acompanhamento. O preenchimento adequado dos campos destas fichas (completude) é essencial para acompanhar a dinâmica da doença e definir prioridades de intervenção. O objetivo deste estudo foi avaliar a completude das fichas de notificações de tuberculose nos municípios prioritários da Bahia (Camaçari, Feira de Santana, Ilhéus, Itabuna, Jequié, Lauro de Freitas, Porto Seguro, Teixeira de Freitas, Paulo Afonso, Barreiras e Salvador), para controle da doença em indivíduos com HIV/AIDS, através dos relatórios de tabulação do Sinan, no período de 2001 a 2010. Os resultados demonstraram que, apesar da completude do campo HIV estar acima de 50%, mais da metade das fichas estavam preenchidas como "não realizado" ou "em andamento", em todos os municípios avaliados no período. A baixa completude das fichas de notificação pode comprometer a qualidade de vigilância dos casos de TB. Os resultados sugerem a necessidade de maior disponibilidade de teste para HIV nesses indivíduos.

One-pot synthesis of graphene-chitosan nanocomposite modified carbon paste electrode for selective determination of dopamine

Background A simple, rapid, low-cost and environmentally friendly method was developed to determine dopamine (DA) in the presence of ascorbic (AA) and uric acid (UA) based on a novel technique to prepare a graphene-chitosan (GR-CS) nanocomposite and modify it on the surface of carbon paste electrode (CPE). For our design, CS acts as a media to disperse and stabilize GR, and then GR plays a key role to selective and sensitive determination of DA. Results Under physiological conditions, the linear range for dopamine was determined from 1 × 10- 4 to 2 × 10- 7 mol/L with a good correlation coefficient of 0.9961 in the presence of 1000-fold interference of AA and UA. The detection limit was estimated to be 9.82 × 10- 8 mol/L (S/N = 3). In order to study the stability and reproducibility, GR/CS/CPE underwent successive measurements in 10 times and then tested once a d for 30 d. The result exhibited 98.25% and 91.62% activities compared with the original peak current after 10-time measurements and 30-d storage. Conclusion The GR/CS/CPE has wide linear concentration range, low detection limit, and good reproducibility and stability, which suggests that our investigations provide a promising alternative for clinic DA determination.

Post-curing conversion kinetics as functions of the irradiation time and increment thickness

Objective: This study evaluated the variation of conversion degree (DC) in the 12 hours following initial photoactivation of a low-shrinkage composite resin (Venus Diamond). Material and Methods: The conversion degree was monitored for 12 hours using Attenuated Total Reflection (ATR) F-TIR Spectroscopy. The composite was placed in 1 or 2 mm rings and cured for 10 or 20 seconds with a LED lamp. ATR spectra were acquired from the bottom surface of each sample immediately after the initial photoactivation (P=0), 30 minutes (P=0.5) and 12 hours after photoactivation (P=12) in order to obtain the DC progression during the post-curing period. Interactions between thickness (T), irradiation time (I) and post-curing (P) on the DC were calculated through ANOVA testing. Results: All the first order interactions were statistically significant, with the exception of the T-P interaction. Furthermore, the shift from P=0 to P=0.5 had a statistically higher influence than the shift from P=0.5 to P=12. The post-curing period played a fundamental role in reaching higher DC values with the low-shrinkage composite resin tested in this study. Moreover, both the irradiation time and the composite thickness strongly influenced the DC. Conclusions: Increased irradiation time may be useful in obtaining a high conversion degree (DC) with a low-shrinkage nano-hybrid composite resin, particularly with 2 mm composite layers.

The influence of mouthrinses and simulated toothbrushing on the surface roughness of a nanofilled composite resin

The aim of this study was to determine the influence of mouthrinses on the surface roughness of a nanofilled composite resin after toothbrushing. One hundred nanofilled composite resin specimens were prepared and randomly distributed into two groups-brushed and non-brushed-and then assigned to five subgroups, according to the mouthrinse solutions (n = 10): Colgate Plax Fresh Mint, Oral B, Cepacol, Colgate Plax, and artificial saliva. Each sample was immersed in 20 mL of the mouthrinses for 1 minute, 5 days per week, twice a day, for a 3-week period. The control group used in the study was one in which the specimens were not subjected to brushing and remained only in artificial saliva. Toothbrushing was performed once a week for 1 minute, for 3 weeks. Surface roughness measurements (Ra) were performed after the immersion period and toothbrushing, by means of a profilometer. Data were analyzed by two-way ANOVA and Tukey's test. Analysis revealed that the association between toothbrushing and Colgate Plax Fresh Mint produced the lowest surface roughness (p < 0.05). All other groups tested (Oral B, Cepacol, Colgate Plax, artificial saliva) exhibited no statistically significant differences between surfaces, whether subjected to toothbrushing or not (p < 0.05). It was concluded that the surface roughness of the nanofilled composite resin tested can be influenced by the mouthrinse associated with toothbrushing.

Degree of conversion of nanofilled and microhybrid composite resins photo-activated by different generations of LEDs

OBJECTIVE:This study aimed at evaluating the degree of conversion (DC) of four composite resins, being one nanofilled and 3 microhybrid resins, photo-activated with second- and third-generation light-emitting diodes (LEDs). MATERIAL AND METHODS: Filtek TM Z350 nanofilled composite resins and Amelogen® Plus, Vit-l-escenceTM and Opallis microhybrid resins were photo-activated with two second-generation LEDs (Radii-cal and Elipar Free LightTM 2) and one third-generation LED (Ultra-Lume LED 5) by continuous light mode, and a quartz halogen-tungsten bulb (QHT, control). After 24 h of storage, the samples were pulverized into fine powder and 5 mg of each material were mixed with 100 mg of potassium bromide (KBr). After homogenization, they were pressed, which resulted in a pellet that was evaluated using an infrared spectromer (Nexus 470, Thermo Nicolet) equipped with TGS detector using diffuse reflectance (32 scans, resolution of 4 cm-1) coupled to a computer. The percentage of unreacted carbon-carbon double bonds (% C=C) was determined from the ratio of absorbance intensities of aliphatic C=C (peak at 1637 cm-1) against internal standard before and after curing of the specimen: aromatic C-C (peak at 1610 cm-1). RESULTS: The ANOVA showed a significant effect on the interaction between the light-curing units (LCUs) and the composite resins (p<0.001). The Tukey’s test showed that the nanofilled resin (FiltekTM Z350) and Opallis when photo-activated by the halogen lamp (QTH) had the lowest DC compared with the other microhybrid composite resins. The DC of the nanofilled resin (FiltekTM Z350) was also lower using LEDs. The highest degrees of conversion were obtained using the third-generation LED and one of second-generation LEDs (Elipar Free LightTM 2). CONCLUSIONS: The nanofilled resin showed the lowest DC, and the Vit-l-escenceTM microhybrid composite resin showed the highest DC. Among the LCUs, it was not possible to establish an order, even though the second-generation LED Radii-cal provided the lowest DC.

Changes in surface roughness and color stability of two composites caused by different bleaching agents

The objective of this study was to evaluate the effect of two bleaching agents (10% and 35% hydrogen peroxide) on the color stability and surface roughness of two composites, one nanohybrid and one nanoparticle. Specimens were polished, aged, stained, bleached and polished again. The action of the bleaching agents on the composites was analyzed using a profilometer (surface roughness) and a spectrophotometer (color stability). The effect of polishing the composites on the surface roughness and the resumption of the composite color was also evaluated. The results were analyzed statistically by ANOVA and Tukey's test at 5% significance level. The analysis indicated that the nanohybrid composite was more affected by staining. The bleaching agents were not able to promote bleaching of either composite over the evaluation period. Surface polishing returned nanohybrid composite to its original color condition, which did not occur for the nanoparticle composite. Additionally, polishing did not return the surface roughness of either composite to its original value. It may be concluded that polishing surface after bleaching should not be the treatment of choice, as it was not possible to reverse the roughness of the composites to their original values, suggesting that a more extensive and irreversible degradation might have occurred.

O objetivo deste estudo foi avaliar o efeito de dois agentes clareadores (peróxido de hidrogênio a 10% e 35%) sobre a estabilidade de cor e rugosidade superficial de dois compósitos, um nanohíbrido e um nanoparticulado. Os espécimes foram polidos, envelhecidos, manchados, clareados e polidos novamente. A ação dos agentes clareadores sobre os compósitos foi analisada em perfilômetro (rugosidade) e um espectrofotômetro (estabilidade de cor). A ação de polimento dos compósitos sobre a rugosidade superficial e a retomada da cor dos compósitos também foi avaliada. Os resultados foram analisados estatisticamente por ANOVA e teste de Tukey (5% de significância). A análise indicou que o compósito nanohíbrido foi mais afetado pelo manchamento. Os agentes clareadores não foram capazes de promover o clareamento dos compósitos ao longo do período de avaliação. O polimento da superfície retornou o compósito nanohíbrido à sua condição de cor original, o que não foi observado para o nanoparticulado. Além disso, o polimento não retornou a rugosidade de superfície dos compósitos para os valores originais. Os autores concluíram que o polimento da superfície após o clareamento não deve ser a opção de tratamento, uma vez que não foi possível inverter a rugosidade dos compósitos à sua rugosidade original, sugerindo que uma degradação mais extensa e irreversível pode ter ocorrido.

Effect of different surface penetrating sealants on the roughness of a nanofiller composite resin

This study evaluated the effectiveness of different sealants applied to a nanofiller composite resin. Forty specimens of Filtek Z-350 were obtained after inserting the material in a 6x3 mm stainless steel mold followed by light activation for 20 s. The groups were divided (n=10) according to the surface treatment applied: Control group (no surface treatment), Fortify, Fortify Plus and Biscover LV. The specimens were subjected to simulated toothbrushing using a 200 g load and 250 strokes/min to simulate 1 week, 1, 3 and 6 months and 1 and 3 years in the mouth, considering 10,000 cycles equivalent to 1 year of toothbrushing. Oral-B soft-bristle-tip toothbrush heads and Colgate Total dentifrice at a 1:2 water-dilution were used. After each simulated time, surface roughness was assessed in random triplicate readings. The data were submitted to two-way ANOVA and Tukey's test at a 95% confidence level. The specimens were observed under scanning electron microscopy (SEM) after each toothbrushing cycle. The control group was not significantly different (p>0.05) from the other groups, except for Fortify Plus (p<0.05), which was rougher. No significant differences (p>0.05) were observed at the 1-month assessment between the experimental and control groups. Fortify and Fortify Plus presented a rougher surface over time, differing from the baseline (p<0.05). Biscover LV did not differ (p>0.05) from the baseline at any time. None of the experimental groups showed a significantly better performance (p>0.05) than the control group at any time. SEM confirmed the differences found during the roughness testing. Surface penetrating sealants did not improve the roughness of nanofiller composite resin.

Este estudo avaliou a efetividade de diferentes selantes aplicados a uma resina nanoparticulada. Quarenta espécimes de Filtek Z-350 foram obtidos depois da inserção do material em um molde de aço inoxidável seguido por fotoativação por 20 s. Os grupos foram divididos (n=10) de acordo com o tratamento superficial aplicado: Grupo controle (sem tratamento superficial), Fortify, Fortify Plus ou Biscover LV. Os espécimes foram submetidos a escovação simulada usando uma carga de 200 g e 250 ciclos/min para simular 1 semana, 1, 3 e 6 meses e 1 e 3 anos, considerando que 10.000 ciclos equivalem a um ano de escovação. Escovas Oral-B de cabeça macia e dentifrício Colgate Total diluído a 1:2 em água foram utilizados. Depois de cada período de simulação, a rugosidade superficial foi medida em triplicata. Os dados foram submetidos à ANOVA de dois fatores e ao teste de Tukey com nível de 95% de confiança. Os espécimes foram observados em microscopia eletrônica de varredura (MEV) depois de cada ciclo de escovação. O grupo controle não foi diferente (p>0,05) que os outros grupos, exceto pelo Fortify Plus (p<0,05), que foi mais rugoso. Nenhuma diferença (p>0,05) foi observada em 1 mês de simulação entre os grupos experimentais e o controle. Fortify e Fortify Plus apresentaram rugosidade regular com o tempo, diferindo da inicial em todos os tempos. Nenhum dos grupos selados mostrou melhor desempenho (p>0,05) que o grupo controle em qualquer um dos tempos. MEV ressaltou as diferenças encontradas durante o teste de rugosidade. Selantes de penetração de superfície não melhoram a rugosidade da resina nanoparticulada.

Comparative evaluation of marginal adaptation between nanocomposites and microhybrid composites exposed to two light cure units.

Background: Recent advances in resin adhesives and restorative materials, as well as an increased demand for esthetics, have lead to the introduction of newer resin-based composites like nanocomposites and light-curing units like light emitting diodes (LEDs). Aim: The present study was conducted to evaluate the effect of conventional quartz tungsten halogen (QTH) curing unit and blue LED on marginal adaptation of microhybrid composite (Filtek Z250) and nanocomposite (Filtek Z350) resins. Materials and Methods: Eighty Class V cavities were prepared on, extracted human premolars and were divided into four groups of 20 each. The four groups were designed according to the restorative resin and light cure unit used microhybrid/QTH, nanocomposites/QTH, microhybrid/LED and nanocomposites/LED. After thermocycling and immersion in 2% Basic Fuschin dye solution, the teeth were sectioned and dye penetration was observed under a stereomicroscope at 20X magnification. Statistical Analysis: All the samples were scored and results were analyzed using the "Kruskal Wallis and Mann Whitney tests" with "Wilcoxone correction." Results: The results revealed least microleakage in microhybrid composites exposed to QTH and maximum in nanocomposites exposed to LED. Conclusion: Microhybrid composites exhibited lesser microleakage than nanocomposite resins.

Fluoride release profile of a nanofilled resin-modified glass ionomer cement

The present study aimed to compare the fluoride (F-) release pattern of a nanofilled resin-modified glass ionomer cement (GIC) (Ketac N100 - KN) with available GICs used in dental practice (resin-modified GIC - Vitremer - V; conventional GIC - Ketac Molar - KM) and a nanofilled resin composite (Filtek Supreme - RC). Discs of each material (n=6) were placed into 4 mL of deionized water in sealed polyethylene vials and shaken, for 15 days. F- release (μg F-/cm²) was measured each day using a fluoride-ion specific electrode. Cumulative F- release means were statistically analyzed by linear regression analysis. In order to analyze the differences among materials and the influence of time in the daily F- release, 2-way ANOVA test was performed (α=0.05). The linear fits between the cumulative F- release profiles of RC and KM and time were weak. KN and V presented a strong relationship between cumulative F- release and time. There were significant differences between the daily F- release overtime up to the third day only for GICs materials. The daily F- release means for RC were similar overtime. The results indicate that the F- release profile of the nanofilled resin-modified GIC is comparable to the resin-modified GIC.

O presente estudo teve como objetivo comparar o padrão de liberação de fluoreto (F-) de um cimento de ionômero de vidro (CIV) nanoparticulado modificado por resina (Ketac N100 - KN) com CIVs disponíveis na prática clínica (CIV modificado por resina - Vitremer - V; CIV convencional - Ketac Molar - KM) e uma resina composta nanoparticulada (Filtek Supreme - RC). Discos de cada material (n=6) foram imersos em 4 mL de água deionizada em frascos de polietileno e agitados durante 15 dias. A liberação de F- (μg F-/cm²) foi medida a cada dia utilizando um eletrodo de F- específico. Os valores de liberação cumulativa de F- foram analisados estatisticamente por análise de regressão linear. Com o objetivo de analisar as diferenças entre os materiais e a influência do tempo na liberação diária de F- foi aplicado o teste ANOVA a dois critérios (α=0,05). A relação entre os padrões de liberação de cumulativo de F- da RC e KM e o tempo foram fracas. Os materiais KN e V apresentaram uma relação forte entre a liberação cumulativa de F- e o tempo. Diferenças significativas foram observadas entre a liberação diária de F- até o terceiro dia somente para os cimentos ionoméricos. Os resultados indicam que o padrão de liberação de F- do CIV modificado por resina nanoparticulado é semelhante ao CIV modificado por resina.

Study of Collagen Immobilization on a Novel Nanocomposite to Enhance Cell Adhesion and Growth

Surface properties of a biomaterial could be critical in determining biomaterial's biocompatibility due to the fact that the first interactions between the biological environment and artificial materials are most likely occurred at material's surface. In this study, the surface properties of a new nanocomposite [NC] polymeric material were modified by combining plasma treatment and collagen immobilization in order to enhance cell adhesion and growth. Methods: NC films were plasma treated in reactive O[2] plasma at 60 W for 120 s. Afterward, type I collagen was immobilized on the activated NC by a safe, easy, and effective one-step process. The modified surfaces of NC were characterized by water contact angle measurement, water uptake, scanning electron microscopy [SEM], and Fourier transformed infrared spectroscopy in attenuated total reflection mode [ATR-FTIR]. Furthermore, the cellular behaviors of human umbilical vascular endothelial cells [HUVEC] such as attachment, growth and proliferation on the surface of the NC were also evaluated in vitro by optical microscopy and 3-[4,5-dimethylthiazol-2-yl]-2,5-diphenyltetrazolium bromide test. Results: The outcomes indicated that plasma treatment and collagen immobilization could improve hydrophilicity of NC. SEM micrograph of the grafted film showed a confluent layer of collagen with about 3-5 jum thicknesses. In vitro tests showed that collagen-grafted and plasma-treated surfaces both resulted in higher cell adhesion and growth state compared with untreated ones. Conclusion: Plasma surface modification and collagen immobilization could enhance the attachment and proliferation of HUVEC onto NC, and the method would be usefully applied to enhance its biocompatibility

Effect of prepolymerized composite megafiller on the marginal adaptation of composite restorations in cavities with different C-factors: An SEM study.

Aim: To evaluate the effect of prepolymerized custom-made composite megafiller and configuration factors (C-factor) on marginal adaptation of resin composite restorations. Materials and Methods: Forty extracted human mandibular molars were divided into four experimental groups consisting of 10 samples each. In groups I and III, class V (configuration factor 5) and in groups II and IV, class II box-shaped cavities (configuration factor 2) were prepared. Groups I and II were restored with a nanofilled composite (Filtek™ Z350 3M ESPE, St Paul, MN, USA) placed in horizontal increments. In groups III and IV, preformed composite megafiller was placed and cavities were restored with nanofilled composite Z-350. After curing, the samples were finished and prepared for examination under low vacuum scanning electron microscope. The data were analyzed with one-way analysis of variance. The significance between the individual groups was calculated by Post hoc test using the Holm-Sidak method ( P≤0.05). Results: The marginal gap values in groups III and IV were significantly lower than in groups I and II, respectively ( P≤0.05). Minimum gap values were seen in group IV. Conclusion: Use of prepolymerized composite megafiller and a lower C-factor decreased the marginal gaps between the tooth and composite restorations.

Effect of filler particles on surface roughness of experimental composite series

OBJECTIVE: The purpose of this study was to evaluate the effect of different filler sizes and shapes on the surface roughness of experimental resin-composite series. MATERIAL AND METHODS: Thirty-three disc-shaped specimens of the series (Spherical-RZD 102, 105, 106, 107, 114 and Irregular-RZD 103, 108, 109, 110, 111, 112) were prepared in a split Teflon mold and irradiated with an halogen light-curing unit (450 mW/cm² for 40 s) at both top and bottom surfaces. The specimens were stored for 3 months in distilled water. The surface roughness values in form of surface finish-vertical parameter (Ra), maximum roughness depth (Rmax) and horizontal roughness parameter (Sm) were recorded using a contact profilometer. The data were analyzed by one-way ANOVA and the means were compared by Scheffé post-hoc test (a=0.05). RESULTS: The lowest surface roughness (Ra) was observed in S-100 (0.079±0.013), while the roughest surface was noted in I-450/700/1000 (0.125±0.011) and I-450/1000 (0.124±0.004). The spherical-shape series showed the smoothest surface finish compared to the irregular-shape ones with higher significant difference (p>0.05). The vertical surface roughness parameter (Ra) values increased as the filler size increased yielding a linear relation (r²=0.82). On the contrary, the horizontal parameter (Sm) was not significantly affected by the filler size (r²=0.24) as well as the filler shape. CONCLUSIONS: Filler particle's size and shape have a great effect on the surface roughness parameters of these composite series.

Comparison of the mechanical properties of two nano-filled composite materials / Comparação das propriedades mecânicas de dois materiais nanocompósitos

OBJETIVO: A finalidade deste estudo foi quantificar e comparar as propriedades mecanicas de dois materiais restauradores nanocompositos disponiveis comercialmente. MATERIAL E METODO: Especimes de dois nanocompositos, Z350TM e GrandioTM, foram polimerizados com luz LED por 30 segundos e submetidos a testes mecanicos. As propriedades testadas incluiram: resistencia flexural, resistencia tensil diametral, resistencia a fratura e microdureza (topo e fundo). RESULTADOS: O Grandio apresentou valores de resistencia flexural media maiores quando comparados com o Z350 (89.1 MPa vs 61.9 MPa). O Grandio demonstrou maior microdureza das superficies de topo de cada composito quando comparada com sua correspondente superficie de fundo. As propriedades de resistencia a fratura e forca tensil diametral nao foram fatores discerniveis neste estudo em particular. CONCLUSAO: Grandio possui maiores valores para propriedade de resistencia flexural e dureza quando comparado com o Z350. Nao houve diferencas entre os dois materiais em relacao a resistencia a fraturas e resistencia a forcas tenseis diametrais.

OBJECTIVE: The purpose of this study was to quantify and compare the mechanical properties of two commercially available nanocomposite restorative materials. MATERIAL AND METHODS: Specimens of two nanocomposites, Z350TM and GrandioTM, were polymerized with a LED light for 20 seconds and subjected to mechanical tests. Properties tested included: flexural strength, diametral tensile strength, fracture toughness and microhardness (top and bottom). RESULTS: Grandio exhibited significantly higher mean flexural strength values when compared to Z350 (89.1 MPa vs 61.9 MPa). Grandio exhibited significantly higher top microhardness values when compared to Z350. Additionally when microhardness for the top surfaces of each composite were compared with their corresponding bottom surfaces, the bottom surfaces demonstrated significantly lower readings. The properties of fracture toughness and diametral tensile strength were non-discerning factors in this particular study. CONCLUSION: Grandio has greater observed values for the properties of flexural strength and hardness when compared with Z350. There was no difference between the two materials with respect to their fracture toughness and diametral tensile strength.

Color stability of a nanofill composite: effect of different immersion media

OBJECTIVE: The aim of this in vitro study was to evaluate the color stability of a nanofill composite resin (Filtek Z350) in different immersion media. MATERIALS AND METHODS: Twelve resin-based composite specimens were prepared using a silicon cylindrical mold measuring ≅1mm of thickness and ≅ 10mm of diameter. Specimens were light-cured for 40 s from both sides using a LED Radii at 1400 mW/cm² and were randomized into 4 groups (n= 3) according to immersion media: coffee, yerba mate, grape juice or water (control solution). A digital spectrophotometer was used to evaluate the color changes at baseline and at 1-week after immersion in each solution. Specimens were stored in the different staining media for 4 h/day during 1 week. The color differences (DE) were analyzed by paired t-test and one-way ANOVA with complementary Tukey test (p<0.05). RESULTS: After 1-week of immersion, a perceptive color change for the group stored in the grape juice compared to baseline (p=0.008) was observed. Coffee and yerba mate did not show any color changes visible for the human eyes or significantly different from the control group (p>0.05) CONCLUSIONS: The findings of the present study suggest that the tested nanofill resin-based composite was susceptible to staining by substances present in the grape juice.

Influence of pulse-delay curing on sorption and solubility of a composite resin

The purpose of this study was to evaluate the sorption and solubility of a composite resin (TPH³; Dentsply) cured with halogen light due to different storage media and curing modes. The methodology was based on the ISO 4049 standard. Two independent groups were established according to the storage time (7 days-G1; 60 days-G2). A stainless steel mould (2 mm x 8 mm Ø) was used. The selected curing modes were: I (Conventional - C): 40s - 600 mW/cm²; II (Pulse I - PD): 3 s - 200 mW/cm² + 2 min (delay) + 39 s - 600 mW/cm²; III (Pulse II): 10 s - 200 mW/cm² + 2 min (delay) + 37 s - 600 mW/cm²; IV (Pulse III): 3 s- 600 mW/cm² + 2 min (delay) + 37 s -600 mW/cm². The media used were: distilled water, 75 percent ethanol and 100 percent chlorophorm. Five repetitions were made for each group. The specimens were placed in a desiccator at 37ºC for 24 h and, after that, at 23ºC for 1 h to be weighed until a constant mass (m1) was obtained. The discs were immersed separately into the 3 media for 7 days (G1) and 60 days (G2), and thereafter reweighed (m2). The reconditioning in the desiccator was done until a constant mass (m3) was obtained. Sorption and solubility were calculated and the data of G1 and the sorption data of G2 were subjected to two-way ANOVA and Tukey's tests (p=0.05). The solubility data of G2 were analyzed by Kruskal-Wallis test (p=0.05). For G1 and G2, no statistically significant differences were found in sorption among curing techniques (p>0.05). The solubility values were negative, which means that there was mass gain. Regarding the storage media, in G2 chlorophorm had the highest sorption values. It may be concluded that the curing modes (C and PD I, II and III) did not affect the sorption of the tested composite resin. However, different storage media influenced sorption behavior. The solubility test demonstrated negative data, masking the real solubility.