Evaluation of type of kinematics on glide path procedures and torsional fatigue resistance after preparation of moderately curved canals

Abstract: Sixty moderately curved canals of mandibular molars classified as Vertucci's type IV canal configuration were selected by micro-CT 1174. The teeth were divided into two groups according to the kinematics used, whether reciprocating or rotary motion (n=30, totaling 60 mesial root canals). The instruments used to perform the glide path procedures had identical features (0.15 mm of tip size, 0.04 mm/mm taper, thermal treatment, and square cross-section), but differed in the direction of the cutting blade. The duration of the procedure and the absolute and percentage frequency of the instruments to reach the full working length were recorded. The torsional test (3630-1; 1992) was performed on both used and unused instruments, to evaluate a possible reduction in the torsional resistance when using the glide path procedure. Statistical analysis was performed using the unpaired t-test and the chi-square test, and the level of significance was set at 5%. The type of kinematics used affected the duration of glide path procedures, and the reciprocating motion seemed to induce less torsional stress during glide path procedures.

Influence of different coronal preflaring protocols on electronic foramen locators precision

Abstract: The aim of this study was to evaluate the influence of different coronal preflaring protocols (absent, conservative and conventional) on the accuracy of Root ZX II, Raypex 6, and RomiApex A-15 electronic foramen locators (EFLs). Twenty mandibular molars with Vertucci's type IV mesial roots were subjected to endodontic exploration and foraminal patency confirmation. Under 16x magnification, its real lengths (RL) were measured and registered (RL1). The canals were then irrigated with 2.5% sodium hypochlorite and electronically measured (EM1) employing the alginate model; all measurements were performed in triplicate by a blind operator using adjusted endodontic hand-files introduced until the apex foramen. Coronal preflaring procedures were sequentially performed with #25/.06 (conservative) and #25/.12 (conventional) instruments; new RLs extents were performed after each coronal preparation protocol (RL2/RL3), as same as electronic measurements (EM2/EM3). The devices error (mm) was evaluated considering the difference between RLs and EMs at each preparation stage; their precision was stablished adopting ±0.5 mm as tolerance margin. The EFLs error significantly reduced after conventional coronal preflaring protocol (p<0.05), which not occur after the conservative one. The best precisions values were noted after conventional preparation as 90% (Root ZX II), 97.5% (Raypex 6), and 92.5% (RomiApex A-15). No significant differences were found in EFLs comparisons, regardless of the coronal protocol tested (p>0.05). Under the conditions tested it can be concluded that the EFLs evaluated were precise. Moreover, the preflaring protocols influences its accuracy's, where the less conservative one produced the best results.

Resumo O objetivo deste estudo foi avaliar a influência de diferentes protocolos de pré-alargamento cervical (ausente, conservador e convencional) na precisão dos localizadores eletrônicos foraminais (LEFs) Root ZX II, Raypex 6 e RomiApex A-15. Vinte molares inferiores com raízes mesiais do tipo IV de Vertucci foram submetidos à exploração endodôntica e confirmação da patência foraminal. Sob ampliação de 16x, seus comprimentos reais (CR) foram medidos e registrados (CR1). Os canais foram então irrigados com hipoclorito de sódio a 2,5% e medidos eletronicamente (ME1) utilizando o modelo em alginato; todas as medidas foram realizadas em triplicata por um operador cego, utilizando limas endodônticas ajustadas introduzidas até o forame apical. Os procedimentos de pré-alargamento cervical foram realizados sequencialmente com os instrumentos #25/.06 (conservador) e #25/.12 (convencional); novas determinações de CRs foram realizadas após cada protocolo de preparação cervical (CR2/CR3), da mesma forma que as medidas eletrônicas (ME2/ME3). O erro dos dispositivos (mm) foi avaliado considerando a diferença entre CRs e MEs em cada estágio de preparação; sua precisão foi estabelecida adotando ± 0,5 mm como margem de tolerância. O erro dos LEFs reduziu significativamente após o protocolo convencional de alargamento cervical (p<0,05), o que não ocorreu após o conservador. Os melhores valores de precisão foram observados após a preparação convencional como 90% (Root ZX II), 97,5% (Raypex 6) e 92,5% (RomiApex A-15). Não foram encontradas diferenças significantes nas comparações entre os LEFs, independentemente do protocolo cervical testado (p>0,05). Sob as condições testadas, pode-se concluir que os LEFs avaliados foram precisos. Além disso, os protocolos de alargamento influenciam sua precisão, onde o menos conservador produziu os melhores resultados.

Tricalcium silicate-based cements: properties and modifications

Abstract: Mineral trioxide aggregate (MTA) has been widely used for different reparative procedures in endodontics. The extensive use of this cement for pulp capping, apexifications, apical surgeries, and revascularization is related to its ability to induce tissue repair and to stimulate mineralization. Several research studies have tested modifications in the composition of MTA-based cements in order to enhance their clinical performance. Novel formulations have been introduced in the market with the aim of increasing flowability. Important properties such as appropriate radiopacity and setting time, color stability, alkaline pH, release of calcium ions, and biocompatibility have to be considered in these new formulations. The latest research studies on the physical, chemical, and biological properties of tricalcium silicate-based cements are discussed in this critical review.

Comparison of two methods of irrigant agitation in the removal of residual filling material in retreatment

Abstract: The aim of this study was to compare the efficacy of passive ultrasonic irrigation and EasyClean for removing residual filling material in retreatment. Twenty-two maxillary lateral incisors with apical curvature were instrumented with ProTaper files and filled with Endofill using the lateral compactation technique. Removal of filling material was performed with Reciproc, Mtwo and ProDesign Logic 50/.01 files. The teeth were inserted in a silicone mould, which was placed in a metal muffle, and split to visualize the residual filling material. The samples were divided into two groups (n = 11) according to the irrigation protocol: Passive ultrasonic irrigation (PUI group) with 3 activations of 20 seconds and EasyClean (Easy Equipamentos Odontológicos, Belo Horizonte, Brazil) (EC group) used in continuous rotation with 3 activations of 20 seconds, both using NaOCl and EDTA. Environmental scanning electron microscopic images of the apical, middle, and cervical thirds were taken before and after the irrigant activation. The Kappa test was used to determine interexaminer agreement. Statistical analysis was performed using Kruskal-Wallis, Mann-Whitney, and Wilcoxon tests (p < 0.05). PUI and EC improved the removal of remnant filling material in all root canal thirds (p < 0.05). PUI and EC presented similar performance in the final step of retreatment (p > 0.05). No significant difference was observed in the removal of filling material in the apical, middle, and cervical thirds in both groups (p > 0.05). EasyClean in continuous rotary motion is useful in retreatment and was shown to be as effective as ultrasonic activation in the removal of remnant filling material.