RESUMO
Purpose@#This study aimed to determine the correlation between various clinical results, including recurrence in patients with breast cancer, and preoperative blood composition ratio and postoperative pathological results. @*Methods@#A total of 444 patients who underwent surgery were included, and the neutrophil-to-lymphocyte ratio (NLR), platelet-to-lymphocyte ratio (PLR), monocyte-to-lymphocyte ratio (MLR), and postoperative pathological results were classified into postoperative cancer stages to confirm the association with various clinical results, including recurrence. @*Results@#The median age of the patients was 51 years. The stages were divided into 1, 2, 3, and 4. Additionally, stages 1 and 2 comprised one group and stages 3 and 4 comprised another group. The cut-off values of the NLR, PLR, and MLR were confirmed to be 1.43, 158.84, and 0.21, respectively. It was noted that the association with recurrence was higher in the group with hormone receptor negative (p<0.001), higher stage (p<0.001), and underwent neoadjuvant chemotherapy (p<0.001). In the association with blood composition ratio and recurrence, survival was high in the PLR group with a high cut-off value (p=0.004). There was no significant relationship in the NLR and MLR groups. In the disease-free survival and overall-survival curves, only the PLR group showed a significant association of 0.003 and 0.001, respectively. The NLR and MLR groups did not show any significant result. @*Conclusion@#No significant association with recurrence and mortality was confirmed in the NLR and MLR groups. However, the preoperative blood test in the high PLR group showed recurrence and mortality rate were high.
RESUMO
PURPOSE@#The purpose of this study was to compare the surface roughness, phase transformation, and surface topography of dental zirconia with three different yttrium oxide compositions under same grinding and polishing conditions. @*MATERIALS AND METHODS@#Three zirconia disks (IPS e.max ZirCAD LT, MT, MT multi, Ivoclar Vivadent AG, Schaan, Liechtenstein) were selected for experimental materials. Sixty-nine bar-shaped specimens were fabricated as 12.0 × 6.0 × 4.0 mm using a milling machine and glazing was conducted on 12.0 × 6.0 mm surface by same operator. With a custom polishing device, 12.0 × 6.0 mm surfaces were polished under same condition. Surface roughness (Ra[µm]) was measured before grinding (C), after grinding (G), and at every 3 steps of polishing (P1, P2, P3). X-ray diffraction and FE-SEM observation was conducted before grinding, after grinding, and after fine polishing (P3). Statistical analysis of surface roughness was performed using Kruskal-Wallis test and Mann-Whitney-U test was used as a post hoc test (α = .05). @*RESULTS@#There were no significant differences of surface roughness between LT, MT, and MM groups. In LT, MT, and MM groups, P3 groups showed significantly lower surface roughness than C groups. X-ray diffraction showed grinding and polishing didn’t lead to phase transformation on zirconia surface. In FE-SEM images, growths in grain size of zirconia were observed as yttrium oxide composition increases. @*CONCLUSION@#Polished zirconia surface showed clinically acceptable surface roughness, but difference in yttrium oxide composition had no significant influence on the surface roughness. Therefore, in clinical situation, zirconia polishing burs could be used regardless of yttrium oxide composition.
RESUMO
PURPOSE@#The purpose of this study was to compare the surface roughness, phase transformation, and surface topography of dental zirconia with three different yttrium oxide compositions under same grinding and polishing conditions. @*MATERIALS AND METHODS@#Three zirconia disks (IPS e.max ZirCAD LT, MT, MT multi, Ivoclar Vivadent AG, Schaan, Liechtenstein) were selected for experimental materials. Sixty-nine bar-shaped specimens were fabricated as 12.0 × 6.0 × 4.0 mm using a milling machine and glazing was conducted on 12.0 × 6.0 mm surface by same operator. With a custom polishing device, 12.0 × 6.0 mm surfaces were polished under same condition. Surface roughness (Ra[µm]) was measured before grinding (C), after grinding (G), and at every 3 steps of polishing (P1, P2, P3). X-ray diffraction and FE-SEM observation was conducted before grinding, after grinding, and after fine polishing (P3). Statistical analysis of surface roughness was performed using Kruskal-Wallis test and Mann-Whitney-U test was used as a post hoc test (α = .05). @*RESULTS@#There were no significant differences of surface roughness between LT, MT, and MM groups. In LT, MT, and MM groups, P3 groups showed significantly lower surface roughness than C groups. X-ray diffraction showed grinding and polishing didn’t lead to phase transformation on zirconia surface. In FE-SEM images, growths in grain size of zirconia were observed as yttrium oxide composition increases. @*CONCLUSION@#Polished zirconia surface showed clinically acceptable surface roughness, but difference in yttrium oxide composition had no significant influence on the surface roughness. Therefore, in clinical situation, zirconia polishing burs could be used regardless of yttrium oxide composition.