Three-dimensional finite element analysis of bone stress distribution around the hip joint prosthesis with stepped stem / 生物医学工程学杂志

Based on the CT data, a medical treatment FE model of hip joint prosthesis with stepped stem was rebuilt according the anatomy of the hip joint. Under the loads of 1.5 times standard body weight (70kg), the mechanical behavior of the treatment model was calculated, and the influence of step structure and distribution for stepped stem on femur stress and stability of total hip replacement were analyzed by three-dimensional finite element analysis (3D-FEA). The results show that the step structure changs the bone stress transmission on the interface of stepped stem and femur, and benefits to reduce stress-shielding in the femur. For the same distribution of step, the reduction of stress-shielding for raised stepped stem is better than that for concave stepped stem. The raised stepped stem of which the steps is distributed one of third part of the stem is of the best effect of reduction of stress shielding in all of the analysis models, and is a beneficial mechanical design to relieves osteoporosis or osteopenia of femur caused by stress-shielding and improve the reliability of it in clinic.

3D finite element analysis of bone stress around distally osseointegrated implant for artificial limb attachment / 生物医学工程学杂志

Using the CT data, we have constructed the finite element models of human femur distally amputated at high-position, middle-position and low-position, along with distally osseointegrated implant under the maximal load during a normal walking cycle. Results of finite element analysis revealed: the maximal stress of implant is produced near the exit of the amputated limb, where the fatigue breakpoint caused by cyclic stress would take place. With the ascending of truncated position, the peri-implant interfacial stress of bone increases. There is severe stress-shielding at the bone-implant interface, and there is concentration of stress at the end of implant and at the 3/4 point of femur, which would lead to bone loss and bone resorption and would shorten the longevity of implant. The results also showed that the curvature of natural bone has notable effect on the stress distribution, which should not be neglected. These data may provide reliable reference for the design and research of osseointegarted artificial limb.

Research of bone bridge-like on plasma sprayed HA coating / 生物医学工程学杂志

Bone formation on hydroxyapatite (HA) coating in the presence of gaps is important for clinical application. Pure Ti and hydroxyapatite coated by plasma sprayed samples were implanted in dog respectively. The implants were surrounded by gaps of 2 mm, and the follow-up period was 12 weeks. Histological examination and histomorphometry revealed that gaps could be bridged by bone provided the hydroxyapatite coating was applied, and that pure Ti implants were surrounded by fibrous tissue with no bone contact at all.

A study of bone-like apatite formation on calcium phosphate ceramics in different kinds of animals in vivo / 生物医学工程学杂志

Bone-like apatite formation on the surface of calcium phosphate ceramics has been believed to be necessary for new bone to grow on the ceramics and to be related to the osteoinductivity of the material. The research of bone-like apatite formation is a great help to understanding the mechanism of osteoinduction. Synthetic porous calcium phosphate ceramics (HA/TCP = 70/30) were implanted intramuscularly in pigs, dogs, rabbits and rats to make a comparative study of the bone-like apatite formation onto the porous HA/TCP ceramics in different animals. Specimens were harvested at 14 days after implantation. Samples were detected for the surface morphology with SEM. The chemical composition of the sample surface after implantation was analyzed with reflection infrared (R-IR). Obvious bone-like apatite formation could be detected in the sections of porous specimens harvested from all animals after 14 days intramuscular implantation. Crystal deposition could be only observed on the surface of the concave regions of the samples collected from dogs, rabbits and rat. On the contrary, evenly distributed flake-shaped crystal could be found on the pore surface and also on the outer surface of the materials implanted in pigs. The morphology of bone-like apatite in pigs was different from that in the others animals. Bone-like apatite was not observed in dense specimen implanted intramuscularly. Bone-like apatite formed faster on specimens implanted in rabbit than that in other animals. This formation sequence is different from the sequence of osteoinductivity of biphasic calcium phosphate ceramics implanted in these animals. The results demonstrated that the formation of bone-like apatite on materials is a prerequisite condition to their osteoinduction but other factors also play important roles in osteoinduction.

A study of bone-like apatite formation on porous calcium phosphate ceramics in dynamic SBF / 生物医学工程学杂志

This study aimed at investigating the influence of the flow rate of simulated body fluid (SBF) (2 ml/100 ml.min) of body fluid in skeletal muscle upon the formation of bone-like apatite on porous calcium phosphate ceramics. The in vitro immersion experiment in SBF flowing at normal physiological rate is referred to as dynamic SBF. The results showed that bone-like apatite could only formed in the pores of porous calcium phosphate when SBF flow at physiological rate (2 ml/100 ml.min) of body fluid in skeletal muscle. At the same time, bone-like apatite could form both in the pores and on the surface of the samples if the flowing physiological solution is 1.5 SBF. When the flowing speed of SBF is higher than normal physiological speed (10 ml/100 ml.min), no bone-like apatite could be detected both on the surface and in the pores of the materials. This result is in concordance with animal experiments. The dynamic SBF simulates the biological environment of bone-like apatite formation in body better than static SBF (SBF does not flow). This method is very useful for the research of the mechanism of bonelike apatite formation, which is the key step of bone growth on biomaterials, and can be used as an effective approach to investigate mechanism of the osteoinduction of calcium phosphate in nonosseous tissues in vivo.

The effects of surface morphology of calcium phosphate ceramics on apatite formation in dynamic SBF / 生物医学工程学杂志

Bone-like apatite formation on the surface of calcium phosphate ceramics has been believed to be the prerequisite of new bone growth on ceramics and to be related to the osteoinductivity of the material. The research of the factors effecting bone-like apatite formation is a great help in understanding the mechanism of osteoinduction. This paper is aimed to a comparative study of in vitro formation of bone-like apatite on the surface of dense and rough calcium phosphate ceramics with SBF flowing at different rates. The results showed that the rough surface was beneficial to the formation of bone-like apatite, and the apatite formed faster in 1.5 SBF than in SBF. Rough surface, namely, larger surface area, increased the dissolution of Ca2+ and HPO4(2-) and higher concentration of Ca2+ and HPO4(2-) ions of SBF and was in turn advantageous to the accumulation of Ca2+, HPO4(2-), PO4(3-) near the ceramic surface. Local supersaturating concentration of Ca2+, HPO4(2-), PO4(3-) near sample surface was essential to nucleation of apatite on the surface of sample.

Inclusion of ginsenoside Rg_3 with hydroxypropyl-?-cyclodextrin / 中草药

Objective To investigate the inclusion of ginsenoside Rg_3 with hydroxylpropyl-?-cyclodextrin (HP-?-CD) in aqueous solutions, inclusion molar ratio of host and guest molecules, and change of thermodynamic parameters during the inclusion process. Methods The measurements of the inclusion mechanism, inclusion molar of the host and guest molecules, and change of thermodynamic parameters were carried out by the following methods: phase solubility, IR, NMR, and TLC methods, respectively. Results The results indicated that the inclusion compound of ginsenoside Rg_3-HP-?-CD was formed. The content analysis of the inclusion compound showed that the inclusion ratio of ginsenoside Rg_3-HP-?-CD was 1∶1. The change in the thermodynamic parameters suggested that the inclusion could proceed (△G

Investigation of Pathogenic Yersinia enterocolitica Distribution in Jixian,Tianjin / 环境与健康杂志

Objective To get the information of the distribution of pathogenic Yersinia enterocolitica in Ji County of Tianjin.Methods Yersinia enterocolitica strains were isolated from diarrhea patients and stocks stool and the biochemical identification,serotyping,PFGE analyses were conducted,PCR was used for virulence gene detection in 2006.Results Five strains of Yersinia enterocolitica were isolated from diarrhea patients and pig stools,all of them were serotype O:3,carring virulence genes ail,ystA,yadA,virF,and four of them had the same PFGE patterns with K6GN11C30021.Conclusion The isolates from patients and pigs belong to the same clone and pig may be the main infectious source of Yersinia enterocolitica for human beings in the county.