A clinical application study of digital manufacturing simple intraoral Gothic arch-tracing device in determining the centric relation of complete dentures / 北京大学学报(医学版)

OBJECTIVE@#To verify the consistency between the digital manufacturing simple intraoral Gothic arch-tracing device and the traditional intraoral Gothic arch-tracing device in determining the centric relation of complete dentures restoration.@*METHODS@#Ten outpatients with edentulous jaws were selec-ted, and the centric relation of the patients was determined by digital manufacturing of simple intraoral Gothic arch-tracing device (T1) and traditional intraoral Gothic arch-tracing device (T2); the difference of clinical operation time between the two methods was recorded; the upper and lower edentulous jaw plaster models were scanned with two kinds of centric relation, the Standard Triangle Language (STL) files imported into Geomagic studio software to apply the best fitting of multiple points of the both upper jaw models, the fitted STL files imported into the 3 shape viewer software, and the maximum position deviations of the vertical, labial (buccal) and lingual directions of the mandibular midline area and molar areas in T1 and T2 groups measured. During the clinical complete dentures try-in, we observed whether there was midline deviation in the mouth of T1 group and T2 group, and whether the occlusion of posterior teeth was stable or not.@*RESULTS@#The mean time spent on determining the centric relation of T1 and T2 groups was (41.90±2.64) min, (57.50±2.37) min respectively. Paired t test was conducted in the two groups, P < 0.01 with significant statistical difference; The mean maximum position deviation between T1 group and T2 group of the midline mandibular region in labial lingual direction was (0.32±0.14) mm, that was (0.40±0.23) mm in vertical direction; the mean maximum position deviation of molar area in buccal lingual direction was (0.35±0.23) mm and that was (0.33±0.20) mm in vertical direction. In the vertical and horizontal directions, the maximum position deviation of mandibles between group T1 and group T2 was controlled within 0.5 mm. In the process of clinical complete dentures try-in, there was no deviation from the center line of dentures. There was not warping, swinging and other poor stability phenomena in T1 and T2 groups.@*CONCLUSION@#The digital manufacturing of simple intraoral Gothic arch-tracing device can be used to determine the centric relation of complete dentures, which can not only save time of clinical operation, but also ensure the accuracy of the centric relation.

Influence of intraoral scan and dental cast scan on occlusal quantitative analysis of virtual dental model / 北京大学学报(医学版)

OBJECTIVE@#To make more accurate occlusal quantitative analysis of three-dimensional (3D) virtual dental models and to compare the occlusal contact obtained by intraoral and dental cast scan.@*METHODS@#In this study, 5 subjects were intraoral scanned using laser scanner (3 shapes, Germany) to obtain the 3D virtual models of one tooth (the first molar), two teeth (the second premolar and the first molar), three teeth (the premolars and the first molar) and their opposite teeth, respectively. The silicone impressions were made and dental stone models were poured for each of them. The dental casts were scanned and then they were fixed to the maximum intercuspal position with a special locating jig for a rescanning of occlusal position. The virtual models taken intraorally and obtained with dental cast scan were introduced to a 3D quantitative analysis system, and some criteria regarding to occlusal contact were calculated and analyzed. The occlusal criteria were mean values of occlusal clearance space between the upper and lower occlusal surface (clearance), occlusal contact area (area), and cusp inclination (angle) of the mandibular first molar. Paired t tests were used to evaluate differences of occlusal criteria between the virtual models obtained with the intraoral scan and dental cast scan (α=0.05).@*RESULTS@#The mean values of occlusal clearance of one to three teeth obtained by way of intraoral scan were smaller than those obtained by way of cast scan by 0.134 mm, 0.177 mm, and 0.207 mm, respectively. While the occlusal contact areas were greater than the cast scan by 8.65 mm2, 10.28 mm2, and 11.46 mm2. No statistically significant differences were found between the cusps inclinations obtained with the two scanning methods, and the interclass correlations were high.@*CONCLUSION@#Occlusal clearance obtained by intraoral scan was less than that by cast scan while the occlusal contact area was greater than the latter, indicating that intraoral occlusal contact was closer. The difference of the standard deviations of occlusal clearance measured by the two methods were small and that of occlusal contact area was influenced by the number of teeth scanned intraorally. There was no statistical difference in cusp inclination between the two methods.

Wear intensity and surface roughness of microhybrid composite and ceramic occlusal veneers on premolars after the thermocycling and cyclic mechanical loading tests / 北京大学学报(医学版)

OBJECTIVE@#To evaluate the wear intensity and surface roughness of occlusal veneers on premolars made of microhybrid composite resin or two kinds of ceramics in vitro after the thermocycling and cyclic mechanical loading tests.@*METHODS@#In the study,24 fresh extracted human premolars without root canal treatment were prepared (cusps reduction of 1.5 mm in thickness to simulate middle to severe tooth wear, the inclinations of cusps were 20°). The prepared teeth were restored with occlusal veneers made of three different materials: microhybrid composite, heat-pressed lithium disilicate ceramic and computer-aided design/computer-aided manufacturing (CAD/CAM) lithium disilicate ceramic in the thickness of 1.5 mm. The occlusal veneers were cemented with resin cement. The specimens were fatigued using the thermocycling and cyclic mechanical loading tests after being stored in water for 72 h. The wear of specimens was measured using gypsum replicas and 3D laser scanner before and after the thermocycling and cyclic mechanical loading tests and the mean lost distance (mm) was used to indicate the level of wear. The surfaces of occlusal contact area were observed and the surface roughness was recorded using 3D laser scanning confocal microscope before and after the fatigue test. Differences between the groups were compared using ONE-way ANOVA(P<0.05).@*RESULTS@#All the specimens successfully survived after the thermocycling and cyclic mechanical loading tests. The mean wear of microhybrid composite group, heat-pressed lithium disilicate ceramic group, and CAD/CAM lithium disilicate ceramic group was (-0.13±0.03) mm, (-0.05±0.01) mm and (-0.05±0.01) mm, the wear of microhybrid composite was significantly higher than the two ceramic groups(P<0.001).The mean surface roughness(Ra)before the fatigue test was(1.24±0.20) μm, (0.75±0.09) μm, (0.73±0.14) μm and it became (1.81±0.24) μm, (1.53±0.26) μm and (1.77±0.23) μm after the test . Before the fatigue test, the surface roughness of microhybrid composite was significantly higher than the two ceramic groups(P<0.001) and after the test, the surface roughness of heat-pressed lithium disilicate ceramic was significantly lower than microhybrid composite(P=0.005) and CAD/CAM lithium disilicate ceramic (P=0.010).@*CONCLUSION@#From the view of wear speed, microhybrid composite was significantly higher than the two kinds of ceramics, but it was similar to enamel when the opposing tooth was natural. The surface roughness before the themocycling and cyclic mechanical loading test of microhybrid composite was significantly higher than that of the two ceramic groups. After the test, the surface roughness of heat-pressed ceramic was significantly lower than that of the other two groups. From the view of surface roughness, heat-pressed ceramic has more advantage.