RESUMO
Objective To explore the feasibility of quartz glass for radiotherapy dosimetry through the experimental study of the thermoluminescence characteristics of synthetic quartz glass. Methods The thermoluminescence glow curves of quartz glass under different annealing conditions were analyzed, the thermoluminescence characteristics of quartz glass were studied, and the measurement parameters were optimized. Using the Co-60 reference radiation field in the National Secondary Standard Dosimetry Laboratory, the quartz glass samples under different annealing conditions were irradiated following the dose levels of radiotherapy, i.e., 0.5, 1.0, 2.0, 4.0, 6.0, 8.0, and 10.0 Gy, respectively. According to the relationship between the absorbed dose of quartz glass and the relative thermoluminescence signal intensity, the linearity and dispersion of the dose response of quartz glass were obtained, and the feasibility of quartz glass for radiotherapy dosimetry was analyzed. Results The linear correlation coefficient of dose response of quartz glass under annealing condition of 430℃ for 10 min was 0.9984, and the dose response dispersion was 0.97% at the absorbed dose of 2 Gy. The linear correlation coefficient of dose response of quartz glass under annealing condition of 600℃ for 1 h was 0.9911, and the dose response dispersion was 1.4% at the absorbed dose of 2 Gy. Conclusion Preliminary results suggest that quartz glass with annealing condition of 430℃ for 10 min has the potential to be used for radiotherapy dosimetry.
RESUMO
@#<b>Objective</b> To calculate the energy dependence of absorbed dose in EBT3 film, and to reveal the error in the measurement of proton absorbed dose by EBT3 film. <b>Methods</b> Beam energy was gradually increased in the clinical photon and proton energy ranges. Geant4 was used to calculate the difference in absorbed dose between EBT3 film and the same volume of water. The results were compared with the theoretical values. <b>Results</b> For photons and protons, the thresholds for absorbed dose with energy dependence were 100 keV and 11 MeV, respectively. The energy dependence was consistent with the theoretical values when the photon and proton energies were higher than the corresponding thresholds, and irrelevant to the theoretical values when energies were lower than the thresholds. The differences between the proton Bragg peak and 50% dose point and the actual positions were less than 1%. <b>Conclusions</b> For protons and photons with high energy, the energy dependence of absorbed dose in EBT3 film is negligible. For protons and photons with low energy, EBT3 film shows very different energy dependence of absorbed dose, which should be taken into consideration. The proton Bragg peak and 50% dose point measured by EBT3 film are basically the same as the actual positions.
RESUMO
Objective:To investigate the radiation dose and its impact for human health after the Fukushima nuclear accident in Japan.Methods: The Fukushima nuclear accident caused by the Richter 9 earthquake of the east sea of Miyagi prefecture in Japan and huge tsunami was analyzed. And the detection results of the radiation dose from the nuclear accident that was named 7th grade event was evaluated whether existed effect for human health.Results: The radiation dose rate of the environment after this nuclear accident from the first nuclear power plant of Fukushima was increased, and the radioactive ranges of134Cs and137Cs mainly came from the leak of nuclear power plant were 100~500PBq and 6~20PBq, respectively. At the same time, the radioactive contaminations were found existed in water and foods, and they had posed a threat for marine organism.Conclusion: The detection result of nuclear accident of Fukushima has higher value for the evaluation of after-effect about human health, and the effects of Fukushima nuclear accident and its impact for life, property and ecological environment are worth pondering.
RESUMO
Objective To study the step aceuracy of 252Cf neutron afterloading radiotherapy machine and the dose deviation caused by step deviation.Methods EBT3 film was used to measure the steps of the 252Cf neutron source,and then the center of each 252Cf neutron source was identified by measuring the optical density value by using the ImageJ software.Double ion chambersmethod was used to measure the dose deviation dlue to the 252 Cf neutron source position shift.Results 252 Cf neutron source step accuracy may amount to 0.01 mm using EBT3 film measurement,when 252Cf neutron source position deviation is less than 3 mm,the dose deviation is less than 2.5％.Conclusions The study on the step accuracy and position deviation of the 252Cf neutron source can provide a reference for the quality control standard of the 252Cf neutron afterloading radiotherapy machine.