Linear dimensional change of edentulous models made of high-density laboratory silicones at different storage times / Alteração dimensional linear de modelos edêntulos fabricados com silicones laboratoriais de alta densidade em diferentes tempos de armazenagem

ABSTRACT Objective: To evaluate the dimensional change of edentulous models made of high density laboratory silicones at different storagetimes. Methods: A metallic master model simulating an edentulous maxilla was used. The model had projections of 1.8 cm located in the regions of canines (A and B) and molars (C and D) allowing the linear measurement of distances AB, BC, CD, DA, AC and BD. A laboratory silicone mold was made for duplication of master model in the following materials (n = 10): G1: Zetalabor 85, G2: Titanium 95, G3: Platinum 95 and G4: Gypsum type III (control). The samples were photographed and measured using a software (Image J) at times T1 (baseline) and T2 (after one week of models fabrication). The data were statistically analyzed using Kruskal- Wallis and Dun non-parametric tests (α = 0.05). Results: The storage time influenced the behavior of the materials evaluated. All groups presented dimensional changes in both times and the group Tit95 presented the best results. Only Zet85 group showed a different behavior related to the region of the model. Conclusions: The high density laboratory silicones showed satisfactory results when compared to the gypsum group. Tit95 was the most stable material and it can be recommended as an edentulous model for total protheses.

RESUMO Objetivo: Avaliar a alteração dimensional de modelos edêntulos fabricados em silicone laboratorial de alta densidade em diferentes tempos de armazenagem. Métodos: Um modelo mestre metálico simulando uma maxila edêntula foi utilizado. O modelo possuía projeções oclusais de 1,8 cm localizadas nas regiões de caninos (A e B) e molares (C e D), permitindo a mensuração das distâncias lineares AB, BC, CD, DA, AC e BD. Um molde foi fabricado em silicone laboratorial para duplicação do modelo mestre com os seguintes materiais (n = 10): G1: Zetalabor 85, G2: Titanium 95, G3: Platinum 95 e G4: Gesso tipo III (controle). As amostras foram fotografadas e mensuradas com auxílio de um software (Image J) nos tempos T1 (baseline) e T2 (após uma semana de confecção). Os dados obtidos foram avaliados estatisticamente utilizando os testes não paramétricos de Kruskal- Wallis e Dunn (α = 0.05). Resultados: O tempo de armazenagem influenciou o comportamento dos materiais avaliados. Todos os grupos apresentaram alterações dimensionais em ambos os temos de avaliação e o G2 apresentou os melhores resultados. Apenas o grupo G1 mostrou alteração dimensional dependente da região mensurada. Conclusão: Silicones laboratoriais de alta densidade mostraram resultados satisfatórias de alteração dimensional quando comparados ao gesso tipo III. O material Titanium 95foi o mais estável e pode ser recomendado como alternativa para a confecção de modelos edêntulos.

Dimensional Accuracy Comparison of Physical Models Generated by Digital Impression/3D-Printing or Analog Impression/Plaster Methods

ABSTRACT: This study aimed to compare the trueness and precision of physical models manufactured chairside (intraoral scanner and 3D printed) or by plaster models obtained using impression with alginate or addition silicone. A full- arch stainless steel die was impressed to obtain ten physical models for each group. The models were measured in a stereomicroscope, considering four linear distances. To assess the precision accuracy, an analysis of the measurement variability was carried out, identified by the coefficients of variation and by the Levene's test to compare the groups. To analyze trueness, the data average was subtracted from the database and compared considering alpha as 5 %. Considering precision, the higher dispersion of data occurred in the models obtained with silicone impression. And for trueness, Kruskal Wallis and Dunn tests results did not indicate differences between the groups in the anteroposterior linear distances (p> 0.05). Only in anterior transverse distance obtained through TRIOS (0.31 mm), it presented lower accuracy compared to the models from silicone impression (0.13 mm); however, at transverse posterior distance, the models from silicone impression showed the lowest accuracy (p 0.05). The physical dental models obtained by digital and analog workflows showed acceptable dimensional accuracy expressed by high precision and trueness. There is no difference between the evaluated intraoral scanner systems and the impression materials for the full-arch impression.

RESUMEN: Este estudio tuvo como objetivo comparar la veracidad y precisión de modelos físicos fabricados en la clínica dental (escáner intraoral e impreso en 3D) o por modelos de yeso obtenidos mediante impresión con alginato o silicona de adición. Una matriz de acero inoxidable de arco completo fue impresa para obtener diez modelos físicos para cada grupo. Los modelos se midieron en un estereomicroscopio, considerando cuatro distancias lineales. Se realizó un análisis de la variabilidad de la medida para evaluar la precisión, identificada por los coeficientes de variación y por la prueba de Levene para comparar los grupos. Para analizar la veracidad, el promedio de los datos se restó de la base de datos y se comparó considerando alfa como 5 %. Considerando la precisión, la mayor dispersión de datos ocurrió en los modelos obtenidos con impresión de silicona. Y para la veracidad, los resultados de las pruebas de Kruskal Wallis y Dunn no indicaron diferencias entre los grupos en las distancias lineales anteroposteriores (p> 0,05). Solo en la distancia transversal anterior obtenida mediante TRIOS (0,31 mm) presentó menor precisión en comparación con los modelos de impresión de silicona (0,13 mm); sin embargo, la distancia transversal posterior, los modelos de impresión de silicona mostraron la menor precisión (p 0,05). Los modelos dentales físicos obtenidos mediante flujos de trabajo digitales y analógicos mostraron una precisión dimensional aceptable expresada por alta precisión y veracidad. No se observó diferencia entre los sistemas de escáner intraoral evaluados y los materiales de impresión para la impresión de arco completa.

Stress distribution in the peri-implant area of pure titanium and titanium-zirconium small implants

Aim: In dental implant treatment, there is a demand for mechanically stronger implants. Despite the existence of several studies showing the clinical success of narrow diameter implants, most of them are based on pure titanium (cpTi) alloys. There is a few clinical evidences of the success rate of titanium-zirconium (TiZr) narrow diameter implants. The aim of this study was to evaluate the stress distribution in the peri-implant area of narrow diameter cpTi and TiZr implants under axial and oblique loads. Methods: Photoelastic models were produced using epoxy resin (PL2, Vishay Precision Group) from a master model. The implants (cpTi and TiZr; Straumann AG) had 3.3 mm in diameter and 12 mm in height. Loads of 100 N and 200 N were applied to the abutment at angles of 0° (axial), 10°, 20°, and 30° (oblique). A circular polariscope (Eikonal) was used under dark field white-light configuration. The isochromatic fringes were analyzed in the peri-implant region in 5 areas, using ASTM table with isochromatic fringes; cervical-mesial, cervical-distal, mid-mesial, mid-distal and apical. Results: In general, under axial and oblique loads, the stress in the TiZr implant was lower than in the cpTi implant. The load of 200 N produced the highest stress values in cpTi and TiZr implants. In both implants and loads, the fringes were located more in apical area at all angles evaluated. Conclusion: It can be concluded that for small implants, the load inclination and intensity change the pattern of stress distribution and the cpTi implant exhibited the highest peri-implant stress

Selamento dentinário imediato: proposição de protocolos clínicos / Immediate dentin sealing: proposition for clinical protocols

O selamento dentinário imediato é uma técnica que visa à aplicação de um sistema adesivo imediatamente após a confecção do preparo dental e antes do procedimento de moldagem para a confecção de restaurações indiretas. Observou-se, através de revisão de literatura, que esta abordagem traz benefícios na resistência de união a cimentos resinosos e na prevenção à sensibilidade pós-operatória de dentes preparados para restaurações indiretas. Diversos sistemas adesivos, assim como cimentos resinosos, com diferentes formulações e técnicas de utilização, estão disponíveis no mercado. Sob esse enfoque, foi proposto um protocolo de utilização da técnica de selamento dentinário imediato para os diferentes tipos de restaurações indiretas(AU)

The immediate dentin sealing is a technique that comprises the application of an adhesive system immediately after tooth preparation and before impression taking for the fabrication of indirect restorations. Based on a literature review, it was observed that this approach has benefits regarding bonding strength of dentin to resin cements and decreases the post operatory sensitiveness of teeth prepared for indirect restorations. A number of adhesive systems, as well as resin cements, with different formulations and application protocols are available. Based on the available information, it was proposed a protocol for the application of the immediate dentin sealing technique for different types of tooth preparation(AU)

Comparative photoelastic study of dental and skeletal anchorages in the canine retraction

OBJECTIVE: To compare dental and skeletal anchorages in mandibular canine retraction by means of a stress distribution analysis. METHODS: A photoelastic model was produced from second molar to canine, without the first premolar, and mandibular canine retraction was simulated by a rubber band tied to two types of anchorage: dental anchorage, in the first molar attached to adjacent teeth, and skeletal anchorage with a hook simulating the mini-implant. The forces were applied 10 times and observed in a circular polariscope. The stresses located in the mandibular canine were recorded in 7 regions. The Mann-Whitney test was employed to compare the stress in each region and between both anchorage systems. The stresses in the mandibular canine periradicular regions were compared by the Kruskal-Wallis test. RESULTS: Stresses were similar in the cervical region and the middle third. In the apical third, the stresses associated with skeletal anchorage were higher than the stresses associated with dental anchorage. The results of the Kruskal-Wallis test showed that the highest stresses were identified in the cervical-distal, apical-distal, and apex regions with the use of dental anchorage, and in the apical-distal, apical-mesial, cervical-distal, and apex regions with the use of skeletal anchorage. CONCLUSIONS: The use of skeletal anchorage in canine retraction caused greater stress in the apical third than the use of dental anchorage, which indicates an intrusive component resulting from the direction of the force due to the position of the mini-implant and the bracket hook of the canine. .

OBJETIVO: comparar as ancoragens dentária e esquelética na retração do canino inferior, por meio do estudo da distribuição de tensões. MÉTODOS: foi confeccionado um modelo fotoelástico de segundo molar a canino, sem o primeiro pré-molar, e simulada a retração do canino inferior com elástico preso a dois tipos de ancoragem: dentária, no primeiro molar conjugado aos dentes adjacentes; e ancoragem esquelética, em gancho simulando o mini-implante. As forças foram aplicadas 10 vezes e observadas no polariscópio circular. As tensões no canino inferior foram registradas em 7 regiões. O teste de Mann-Whitney foi aplicado para comparar as tensões em cada região, considerando os dois sistemas de ancoragem. As tensões nas regiões perirradiculares do canino foram comparadas pelo teste de Kruskal-Wallis. RESULTADOS: as tensões foram similares tanto na região cervical quanto no terço médio. No terço apical, as tensões associadas à ancoragem esquelética foram maiores que as tensões associadas à ancoragem dentária. Os resultados do teste de Kruskal-Wallis mostraram que as maiores tensões foram identificadas nas regiões cervicodistal, apicodistal e na região do ápice com o uso da ancoragem dentária; e com o uso da ancoragem esquelética, as maiores tensões se localizaram nas regiões apicodistal, apicomesial, cervicodistal e no ápice. CONCLUSÃO: o uso de ancoragem esquelética na retração promoveu maior tensão no terço apical do que o uso da ancoragem dentária, indicando um componente intrusivo devido à direção da força decorrente da posição do mini-implante e do gancho do braquete do canino. .

Influence of the casting material on the dimensional accuracy of dental dies

The purpose of this study was to evaluate the dimensional accuracy of different materials used in the confection of dies. Two stainless steel standard models were confected. One of the models, which was 2 mm larger than the other model, was used to provide a uniform relief for the two-step putty-wash impression technique. Thirty impressions were obtained using a polyvinyl siloxane impression material and randomly divided into three groups (n = 10) according to the type of casting material: type IV dental stone, commercially available epoxy resin (Tri-Epoxy), and industrial epoxy resin (Sikadur). After the setting/polymerization of the casting material, the dimensional stability was measured in terms of the height, diameter of the base and diameter of the top from the obtained dies and from the standard metal model using a profile projector. Results were analyzed by ANOVA and Dunnet test (α = 0.05). In the height values, no significant difference was observed between the groups, except for Sikadur casts, which showed lower mean values. The Tri-Epoxi group showed statistically lower mean base diameter values, compared with the other groups, and both epoxy resin groups showed statistically lower mean top diameter values, compared with that for the type IV dental stone group. We concluded that type IV gypsum and the commercially available epoxy resin showed similar behavior in most areas. The industrial epoxy resin did not show the same characteristics, although the diameter of the base obtained with it was similar to that obtained with type IV dental stone.

Evaluation of the accuracy of different transfer impression techniques for multiple implants

The aim of this study was to evaluate the accuracy of three implant transfer impression techniques. Four groups (n = 5) were defined, according to the technique: TC - tapered copings without splint; SC - square copings without splint; SCS - square copings splinted with dental floss and acrylic resin, and CG (control group) - master model with four external hexagonal implants and a superstructure. Individual trays and polyether were used for the impression. All casts were checked for their fit into the master superstructure; for this, all four screws were placed in the implants. Digital photos were taken and images were analyzed using UTHSCSA ImageTool software. Statistical analyses were performed using one-way analysis of variance and Student’s t test (p < 0.05). The means and standard deviation were (µm): CG = 2.03 ± 0.00, TC = 14.74 ± 3.41, SC = 12.08 ± 2.56, and SCS = 6.51 ± 0.09. The control group was found to be statistically different from the TC and SC groups. Within the limitations of this study, all groups presented clinically acceptable standard gap values, and the SCS group showed no statistical difference in relation to the CG (control group), demonstrating more accuracy and fidelity to transfer implants.

Comparação da variação da temperatura produzida por dois tipos de instrumentos cortantes rotatórios diamantados no preparo cavitário / A comparison of the temperature variation produced by two kinds of diamond rotatory cutting instruments on the cavity preparation

O objetivo desse estudo foi comparar as variações de temperatura no interior da câmara pulpar provocadas por dois tipos de instrumento cortante rotatório (ICR), a ponta diamantada padrão e Turbo, que promete redução na transmissão de calor. Foram realizados preparos para coroa total na face vestibular de vinte molares humanos extraídos. Os dentes foram divididos em 2 grupos (n-10): Grupo 1 - ponta diamantada padrão nº 4219; Grupo 2 - ponta diamantada Turbo nº 4219T. Para cada preparo foi utilizado um novo ICR e a profundidade do preparo foi de 1,4mm. A espessura de dentina foi padronizada em 2,81 mm. Para leitura das temperaturas foi introduzido um dispositivo termopar na câmara pulpar. Os dados foram transferidos para o software IR-graph e submetidos ao teste Mann-Whitney (p<0,05). Resultados: os valores de variação de temperatura (Celsius): Grupo 1 ±0,55 ºC; Grupo 2 – ± 0,76ºC. Os preparos cavitários realizados com os dois tipos de ICRs geraram alterações de temperatura semelhantes (p>0.05). Os ICRs padrão e Turbo apresentaram o mesmo comportamento quanto à capacidade de gerar calor.

Objective: The objective of this study was to compare the temperature variations of pulp chamber caused by two types of diamond burs: standard and Turbo, which promises a reduction in heat transfer. Twenty full crown preparations were made on the vestibular human molars. The teeth were divided into 2 groups (n-10): Group 1 – diamond bur standard No. 4219, Group 2 – diamond bur Turbo No. 4219T. For each preparation was used a new bur and the depth of the preparation was 1.4 mm. The thickness of dentine was standardized to 2.81 mm. To read the temperature, thermocouple device was introduced in the pulp chamber. Date were transferred to IR-graph software and submitted to the Mann-Whitney test (p<0.05). Results: The values of temperature (Celsius): Group 1 - ±0,55 ºC; Group 2 - ±0,76 °C. The dental cavities made with two kinds of burs generated similar changes in temperature (p> 0.05). The diamond burs standard and Turbo had the same behavior as the ability to generate heat.

Influence of anatomic reference on the buccal contour of prosthetic crowns

During clinical practice, when performing prosthetic rehabilitation with single crowns, improper reproduction of the dental contour by the dental laboratory is a common occurrence. Therefore, the present study evaluated the fidelity of the reproduction of the buccal contour in an upper left canine performed by three Dental Prosthesis Technicians (DPT) using the indirect laminate veneer technique. First, the DPTs confected the veneers based on a model obtained from the upper arch of a dental dummy, containing a replica of an upper left canine with a prosthetic preparation for a laminate veneer. Then, the same DPTs received other identical models, now with the replica of the upper left canine with no preparation, to be used as an anatomical reference for confecting the laminate veneers. The laminate veneers were then bonded to the plaster models and had their buccal contour individually measured. Measurements were also made of the buccal contour of the reference canine. The data were analyzed by ANOVA and the t-test (p = 0.05). Results showed 100 percent of buccal overcontour when the laminate veneers were compared to the reference canine, regardless of which DPT confected the veneer and regardless of using or not the anatomical reference. The DPTs who participated in the present study were unable to acomplish a faithful anatomical reproduction of the buccal contour, creating an overcontour in all samples. This situation may be responsible for increasing the probability of periodontal and esthetic harm in clinical practice.

Surface roughness of acrylic resins processed by microwave energy and polished by mechanical and chemical process

The aim of this study was to evaluate the influence of polymerization methods (microwave energy - MW, and water bath - WB) and polishing techniques (chemical - C and mechanical - M) on the surface roughness of one heat-polymerized acylic resin (Vipi-Cril). Forty acrylic resin disk-shaped samples were made according to ADA specification nº 12. Half of samples were processed by microwave energy (500W for 3 minutes), and the other half by water bath (74±1 ºC for 9 hours). After deflasking, the samples were trimmed with a sequence of abrasive aluminum oxide sandpapers of different grades (180, 220 and 400) and divided in 4 groups according to polymerization methods and polishing techniques: G1: MW+CP, G2: MW+MP, G3: WB+CP and G4: WB+MP. Surface roughness values were measured using a Surfcorder SE 1700 rugosimeter (Kosaka Laboratory Ltd, Kosaka, Japan). Mann-Whitney test (p=.05) indicated significant differences between polishing methods processed by microwave energy (p= .0018), and between polishing methods processing by water bath (p= .0002). Samples processed by both methods (water bath or microwave energy) showed smoother surfaces when polished by mechanical polishing method, and polymerization methods did not influence in surface roughness.