Comparação entre Reciproc Blue e quatro instrumentos réplicas: aspectos metalúrgicos, geometria, comportamento em torção e flexão / Comparison between Reciproc Blue and four replicalike instruments: metallurgical aspects, geometry, and behavior in torsion and flexion

A introdução da liga NiTi na endodontia proporcionou a fabricação de instrumentos com excelentes propriedades mecânicas, e uma das principais características é a possibilidade de alteração das temperaturas de transformação da liga, o qual pode possibilitar a presença de martensita em temperatura ambiente e consequentemente um efeito memória de forma. Entretanto, alguns dos sistemas comercializados atualmente possuem pouca ou nenhuma informação científica relatando suas propriedades mecânicas, características de design e métodos de fabricação. O objetivo deste trabalho foi comparar características geométricas, metalúrgicas e propriedades mecânicas (resistência à torção e flexão) de instrumentos Reciproc Blue (VDW, Munique, Alemanha), e quatro sistemas reciprocantes réplicas. Um total de 39 instrumentos de cada um dos sistemas reciprocantes, Reciproc Blue (RB), Prodesign R (PDR), V File (VF), V+ File (V+) e Univy One (UO) foram utilizados na pesquisa. O programa de Image J foi utilizado para mensuração dos diâmetros a cada milímetro da parte ativa e da área da seção transversal a 3 mm da ponta dos instrumentos. Imagens de MEV da parte ativa foram realizados para avaliar o acabamento superficial dos instrumentos. A composição atômica, fases presentes e temperaturas de transformação foram verificadas através de EDS, DRX e DSC, respectivamente. A flexibilidade foi aferida através de ensaios de dobramento até 45º conforme a especificação ISO 3630-1, e os ensaios de resistência à torção foram realizados de acordo com a especificação Nº28 ANSI/ADA. Todos os instrumentos apresentaram uma quantidade aproximadamente equiatômica de níquel e titânio. A análise qualitativa das fases cristalinas realizada através de ensaios de DRX, demonstrou a predominância de Fase R em todos os grupos, com exceção do grupo UO que apresenta uma mistura de fase R e martensita B19'. Na avaliação da área da seção, o instrumento RB obteve valores intermediários, os instrumentos PDR e V+ possuem menores valores e os instrumentos VF e UO possuem maiores valores. Observou-se grande impacto da geometria sobre as propriedades mecânicas, sendo que aqueles sistemas que apresentavam menor área que RB (PDR, V+) mostraram-se mais flexíveis e menos resistentes à torção (p<0.05), e o instrumento VF que teve maior área apresentou, como esperado, menos flexibilidade (p<0.05) e resistência torcional semelhante (p>0.05). A única exceção se deu com o sistema UO, que embora apresentasse uma maior área de seção, mostrou-se mais flexível e menos resistente à torção, provavelmente por influência da maior quantidade de martensita presente à temperatura ambiente. Nenhum dos instrumentos réplicas avaliados apresentaram características e comportamento mecânico iguais ao sistema padrão RB. Sugere-se que mais estudos devem ser realizados para a comparação do comportamento clínico destes instrumentos.

The introduction of NiTi alloy in endodontics has allowed the manufacturing of instruments with excellent mechanical properties, and one of the main characteristics is the ability to change alloy's transformation temperature, which can enable the presence of martensite at room temperature and consequently favor a shape memory effect. However, some of the currently marketed systems have limited or no scientific information regarding their mechanical properties, design characteristics, and manufacturing methods. The aim of this study was to compare the geometric characteristics, metallurgical aspects, and mechanical properties (torsional and flexural strength) of Reciproc Blue instruments (VDW, Munich, Germany) with four replica-like reciprocating systems. A total amount of 39 instruments from each reciprocating system, namely Reciproc Blue (RB), Prodesign R (PDR), V File (VF), V+ File (V+), and Univy One (UO), were used in the study. The Image J program was used to measure the diameters at every millimeter along the instruments active portion and the cross-sectional area at 3 mm from the instrument tip. SEM images of the active portion were obtained to evaluate the surface finishing of the instruments. Atomic composition, phases present, and transformation temperatures were determined through EDS, XRD, and DSC analyses, respectively. Flexibility was assessed by bending tests up to 45° according to ISO 3630-1 specifications, and torsional strength tests were performed according with ANSI/ADA Specification No. 28. All instruments exhibited an approximately equiatomic composition of nickel and titanium. Qualitative analysis of the crystalline phases using XRD tests demonstrated the predominance of the R-phase in all groups, except for the UO group, which exhibited a mixture of Rphase and B19' martensite. In terms of diameter and cross-sectional area evaluation, the RB instrument obtained intermediate values, while the PDR and V+ instruments had smaller values, and the VF and UO instruments had larger values. A significant impact of geometry on mechanical properties was observed, with systems exhibiting a smaller area than RB (PDR, V+) being more flexible and less torsion-resistant (p<0.05), and the VF instrument with a larger area showed, as expected, less flexibility (p<0.05) and similar torsional resistance (p>0.05). The only exception was the UO system, which, despite having a larger geometric configuration, exhibited greater flexibility and less torsional resistance, likely due to the higher amount of martensite present at room temperature. None of the replica-like instruments evaluated showed identical characteristics and mechanical behavior to the standard RB system. Further studies are suggested to compare the clinical performance of these instruments.

Evaluation of the mechanical properties of different materials for manufacturing occlusal splints

Abstract This study aimed to compare the mechanical properties of various occlusal plate materials by analyzing surface roughness, Knoop microhardness, flexural strength, and modulus of elasticity. Fifty samples were prepared and classified as SC (self-curing acrylic resin), WB (heat-cured acrylic resin), ME (acrylic resin polymerized by microwave energy), P (resin print), and M (polymethylmethacrylate polymer block for computer-aided design/computer-aided manufacturing). The data were analyzed using a one-way analysis of variance and Tukey's honestly significant difference test. Surface roughness was the same in all groups. The surface hardness of group M was statistically superior. The samples from groups P and M had higher flexural strength than other samples. The modulus of elasticity of group SC was statistically lower than that of other groups. The mechanical properties of the materials used to make the occlusal plates differed, and group M achieved the best results in all analyses. Therefore, clinicians must consider the material used to manufacture long-lasting and efficient occlusal splints.

Microbiological analysis of bacterial sealing of internal conical implants with different taper angles

Abstract The present study evaluated the effect of the taper angle of different internal conical connection implants and cyclic loading on the implant-abutment bacterial seal. A total of 96 implant-abutment sets were divided into eight groups. Four groups of different taper degrees with cyclic mechanical loading of 500,000 cycles per sample, with a 120-N load at 2 Hz before analysis [16DC (16-degree, cycled), 11.5DC (11.5-degree, cycled), 3DC (3- degree, cycled) and 4DC (4- degree, cycled)] were compared to four control groups without cyclic loading [16D (16-degree), 11.5D (11.5-degree), 3D (3-degree), and 4D (4-degree)]. Microbiological analysis was performed by immersing all samples in a suspension containing Escherichia coli and incubating them at 37°C. After 14 days, the presence of bacterial seals was evaluated. Fisher-Freeman-Halton exact tests and binomial tests were performed (5% significance level). The groups showed significant differences in bacterial seal, and mechanical load cycling improved the bacterial seal in the 3DC group. In all other groups, no significant differences in bacterial seal were found between cycled and uncycled samples. To conclude, the internal conical connection with a 3-degree taper angle showed better results than the other connection with different angles when subjected to load cycling. However, none of the angles tested were fully effective in sealing the implant-abutment interface.

Biocomponents Based on Hydroxiapatite: Influence of Sterilization on the Mechanical Resistance / Biocomponentes à base de hidroxiapatita: Influência da esterilização na resistência mecânica

Abstract Objective This study aimed to evaluate the influence of sterilization on the compressive and flexural mechanical strength of hydroxyapatite-based biocomponents obtained through freeze-dried bovine bone, and its association with chitosan. Methods Freeze-dried bovine bone was processed into 100 μm particles and mixed with 50% of its weight in chitosan. The mixture was packed in metallic molds for preparing the specimens, and sterilized at 127°C using an autoclave for subsequent experimentation. The specimens were subjected to compression and flexion tests following norm 5833 of the International Organization for Standardization (ISO), with 6 × 12 mm cylindrical blocks (for compression tests) and 75 × 10 × 3.3 mm plates (for flexion tests) as samples. The samples were divided into four groups of 20 specimens each, with 10 for compression and 10 for flexion tests. Three groups were sterilized (autoclave, gamma rays, and ethylene oxide), whereas the fourth group (control) was not. The mechanical tests obtained from the different sterilization processes were compared using analysis of variance (ANOVA, p< 0.05), followed by the Tukey multiple comparison test of means, with a 95% confidence interval. Results The specimens presented mean compressive strengths of 10.25 MPa for the control group and 3.67 MPa, 9.65 MPa, and 9.16 MPa after ethylene oxide, gamma ray, and autoclave sterilization, respectively. Flexion test results showed an average resistance of 0.40 MPa in the control group, and 0.15 MPa, 0.17 MPa, and 0.30 MPa after ethylene oxide, gamma ray, and autoclave sterilization, respectively. There were statistically significant differences observed in the maximum compression of the ethylene oxide-sterilized group compared with that of the control group (p= 0.0002), gamma ray-sterilized (p= 0.0003), and the autoclaved (p= 0.0006) groups. There was a statistically significant difference in maximum flexion of the specimens sterilized by gamma rays when compared with the control group (p= 0.0245). However, low flexural strengths were observed in all specimens. Conclusion The autoclave sterilization group did not result in statistically significant differences in either compression or flexion strength tests. Thus, the autoclave proved to be the best sterilization option for the hydroxyapatite-based biocomponents in this study.

Resumo Objetivo O objetivo deste estudo foi avaliar a influência da esterilização na resistência mecânica à compressão e flexão de biocomponentes à base de hidroxiapatita obtida a partir de osso bovino liofilizado e sua associação com quitosana. Métodos O osso bovino liofilizado foi processado em partículas de 100 μm e misturado à quitosana em proporção de 50% de seu peso. A mistura foi acondicionada em moldes metálicos para preparo dos espécimes e esterilizada a 127°C em autoclave para posterior experimentação. Os espécimes foram submetidos a ensaios de compressão e flexão seguindo a norma 5833 da International Organization for Standardization (ISO); os espécimes eram blocos cilíndricos de 6 × 12 mm (para ensaios de compressão) e placas de 75 × 10 × 3,3 mm (para ensaios de flexão). As amostras foram divididas em quatro grupos de 20 espécimes cada, sendo 10 para ensaios de compressão e 10 para ensaios de flexão. Três grupos foram esterilizados (por autoclavagem, raios gama e óxido de etileno), enquanto o quarto grupo (controle) não foi. Os testes mecânicos obtidos nos diferentes processos de esterilização foram comparados por análise de variância (ANOVA, p< 0,05) seguido pelo teste de comparação múltipla de médias de Tukey, com intervalo de confiança de 95%. Resultados Os espécimes apresentaram resistências médias à compressão de 10,25 MPa para o grupo de controle e 3,67 MPa, 9,65 MPa e 9,16 MPa após esterilização com óxido de etileno, raios gama e autoclavagem, respectivamente. Os resultados do teste de flexão mostraram uma resistência média de 0,40 MPa no grupo de controle, e 0,15 MPa, 0,17 MPa e 0,30 MPa após esterilização com óxido de etileno, raios gama e autoclavagem, respectivamente. A compressão máxima observada no grupo esterilizado com óxido de etileno foi estatisticamente diferente à obtida no grupo de controle (p= 0,0002), esterilizado com raios gama (p= 0,0003) e autoclavado (p= 0,0006). A flexão máxima dos espécimes esterilizados com raios gama foi estatisticamente diferente à observada no grupo de controle (p= 0,0245). No entanto, a resistência à flexão foi baixa em todos os espécimes. Conclusão A esterilização em autoclave não foi associada a diferenças estatisticamente significativas nos testes de compressão ou flexão. Assim, a autoclave foi a melhor opção de esterilização para os biocomponentes à base de hidroxiapatita neste estudo.

Avaliação in vitro da razão base/topo de dureza e da resistência de união push-out entre uma resina composta contendo diatomita e uma resina composta bulk-fill / In vitro evaluation of the base/top hardness ratio and push-out bond strength between a diatomite-containing composite resin and a bulk-fill composite resin

A escassez de dados científicos que validem os benefícios da diatomita para as propriedades físicas da resina composta Zirconfill® torna imperioso a realização de novos estudos, principalmente no tocante a utilização dessa resina contendo diatomita em restaurações semidiretas. Objetivo: Avaliar in vitro a polimerização e resistência de união entre uma resina composta contendo diatomita e de uma resina composta bulk-fill após 24 horas e após 06 meses de envelhecimento em água. Materiais e métodos: Foram utilizados 28 incisivos bovinos para produzir cavidades dentinárias cônicas (4,8 mm de diâmetro maior x 2,8 mm de diâmetro menor x 4 mm de espessura) e fator C de magnitude 3,1. Esses preparos cavitários (n=28) foram restaurados com as resinas compostas Filtek™ One Bulk-fill (BF) (3M ESPE) ou Zirconfill ® (ZF) (BM4), através da técnica semidireta, utilizando o sistema adesivo Single Bond Universal (3M ESPE) e o cimento resino dual Relyx™ Ultimate (3M ESPE). A análise da polimerização foi realizada através da razão base/topo (B/T) de dureza Vickers. E a resistência de união RU foi realizada através do teste de extrusão push-out em máquina de ensaio universal. As amostras foram armazenadas em água destilada a 37 ºC por 24 horas ou 06 meses, mas apenas a RU avaliou as amostras após 06 meses de envelhecimento. Os dados da B/T e da RU foram submetidos à análise de variância (ANOVA) a um e a dois critérios, respectivamente, com pós-teste de Tukey (p <0.05). Resultados: Não houve diferença estatisticamente significativa entre as resinas compostas na B/T. Para a RU, a resina composta ZF mostrou valores maiores do que a resina BF em ambos os tempos avaliados. Não houve diferença estatisticamente significativa de nenhuma resina na avaliação ao longo do tempo. Conclusão: A resina composta contendo diatomita mostrou-se promissora quando utilizada em restaurações semidiretas, visto que obteve resultados similar e até superior a resina composta bulk-fill (AU).

The scarcity of data validating scientific diatomite benefits for physical properties of Zirconfill® resin composite makes essential to develop new studies, especially regarding the use of this resin composite containing diatomite in semi-direct restorations. Aim: To evaluate in vitro the cure and bond strength between a resin composite containing diatomite and a bulk-fill resin composite after 24 hours and after 06 months of water storage. Materials and methods: Twenty-eight bovine incisors (n=28) were used to produce conical dentinal cavities (4,8 mm of larger diameter x 2,8 mm of smaller diameter x 4 mm of thickness) and C-factor of magnitude 3.1. These cavities were restored with Filtek™ One Bulk-Fill (BF) (3M ESPE) or Zirconfill® (ZF) (BM4) resin composites, through the semi-direct technique, using Scotchbond™ Universal (3M ESPE) adhesive system and Relyx™ Ultimate (3M ESPE) dual resin cement. The cure analysis was performed through bottom-to-top (B/T) ratio of vickers hardness, while bond strength (RU) was performed through the push-out test in a universal testing machine. The specimens were stored in distilled water at 37 ºC for 24 hours or 06 months, but only RU analyzed the specimens after 06 months aging. B/T and RU data were, respectively, submitted to one-way and two-way analysis of variance (ANOVA) with Tukey's post-test (p <0.05). Results: There was no statistically significant difference between the composite resins in B/T. For RU, the ZF composite resin showed higher values than the BF resin at both evaluated times. However, there was no statistically significant difference in resin composites over time. Conclusion: The resin composite containing diatomite showed promise when used in semi-direct restorations since it obtained similar or even superior results to bulk-fill resin composite (AU).

Long-term effects of simulated gastric juice alternated with brushing on hardness, substance loss, flexural strength and reliability of CAD-CAM monolithic materials

Abstract Objectives: The purpose of this study is to evaluate, over a simulated 5-year period, the effect of simulated gastric juice alternated with brushing on CAD-CAM monolithic materials considering microhardness, substance loss, flexural strength, and reliability of the materials. Methodology: Blocks from Lava Ultimate (LU), Vita Enamic (VE), IPS Empress CAD (EMP), IPS e.max CAD (EMAX), and Vita Suprinity (VS) were milled into cylinders and sliced into disks. The EMAX and VS were crystallized, and all specimens were polished with silicon carbide papers and allocated as follows: 1) artificial saliva + brushing or 2) simulated gastric juice (0.113% hydrochloric acid (HCl) solution in deionized water, pH 1.2) + brushing, simulating 1, 3, and 5 years of clinical function. Each year of clinical function was simulated by three repetitions of immersion for 3 hours in artificial saliva or simulated gastric juice followed by 1,217 brushing cycles. The microhardness and substance loss were evaluated at baseline (T0) and at each year by using a Vickers hardness tester and an analytical balance. The biaxial flexural strength (BFS) test was performed in a mechanical testing machine at the end of the 5th year. Weibull modulus was calculated from the BFS data. Results: The microhardness of the LU was not influenced by the treatment, whereas that of the other materials, in certain years, was significantly lower in the gastric juice + brushing groups in comparison with artificial saliva + brushing groups. In general, the materials did not present a significant change in microhardness over time, for either of the treatments. The LU alone showed greater substance loss in the gastric juice + brushing groups for every year. In both treatments, the LU, VE, and EMP exhibited a significant increase in the substance loss over time. The treatment did not affect the BFS of the materials. The gastric juice + brushing decreased the reliability of the VE. Conclusions: All materials were somehow impaired by the gastric juice + brushing in at least one of the evaluated parameters, except for the BFS. However, in a deeper analysis, the LU would be the least indicated materials, followed by VE, for patients with eating disorders.

Fiberglass versus cast metal posts: a practical review based on mechanical properties / Pinos de fibra de vidro versus metal fundido: uma revisão prática baseada em propriedades mecânicas

The current review aimed to compare the mechanical properties and clinical behavior of fiberglass and cast metal posts. It included in-vitro studies, finite element analysis, clinical studies, and systematic reviews that evaluated fiberglass and metal posts with reliable methodologies. The reports in the literature diverge on tooth failure modes and stress distributions in the root according to different posts. Investigations suggest that fiberglass posts are preferable because their elastic modulus is similar to dentin. Other studies mention that the flexibility of fiber posts may damage the interface. The fracture load values of different studies could not be compared. The presence of a ferrule seems beneficial. Cast metal posts provide higher characteristic strength to the set but with more unfavorable failures. Intraradicular posts with a lower elastic modulus produce more stress between the cement layer and dentin. In conclusion, fiberglass and cast metal posts can be used with a ferrule. Cast metal posts seem more appropriate for weakened teeth. The presence of a ferrule benefits the system. Weakened teeth tolerate higher loads when restored with cast metal posts, but when these posts fail, the only solution is tooth extraction. Clinical follow-ups cannot yet detect differences between the survival rates of intraradicular fiberglass and cast metal posts (AU)

O objetivo da presente revisão foi comparar as propriedades mecânicas e o comportamento clínico de pinos de fibra de vidro e núcleos metálicos fundidos. Estudos laboratoriais, analise por elementos finitos, estudos clínicos e revisões sistemáticas que avaliaram pinos de fibra de vidro e metálicos, com metodologia confiável foram selecionados. A literatura mostra-se bastante controversa sobre os modos de falha do dente e a distribuição de tensões na raiz de acordo com diferentes tipos de pinos. Algumas investigações sugerem que pinos de fibra de vidro são preferíveis porque seu módulo de elasticidade é semelhante ao da dentina, enquanto outras mencionam que a flexibilidade do pino de fibra pode ser prejudicial à interface adesiva. Os valores de carga de fratura em diferentes estudos não podem ser comparados. A presença de férula é benéfica. O núcleo metálico fundido resulta em maior resistência característica do conjunto, mas falhas mais desfavoráveis. Também, pinos com menor módulo geram mais tensão entre a camada de cimento e a dentina. Em conclusão, verificou-se que tanto pino de fibra de vidro como núcleo metálico fundido podem ser utilizados quando a férula está presente. Os núcleos metálicos fundidos parecem ser mais indicados para dentes fragilizados. É evidente que a presença de férula é benéfica para o sistema. Dentes fragilizados toleram cargas maiores quando restaurados com núcleos metálicos fundidos; porém, quando falham, a única solução é a extração do dente. Os acompanhamentos clínicos ainda não são capazes de detectar diferença entre as taxas de sobrevivência dos pinos de fibra de vidro e núcleos metálicos (AU)

Biological and physico-mechanical properties of poly (methyl methacrylate) enriched with graphene oxide as a potential biomaterial / Propiedades físicas-mecánicas-biológicas del poli (metilmetacrilato) enriquecido con óxido de grafeno como potencial biomaterial

Objective: To determine the cytotoxicity and effects of graphene oxide (GO) on cellular proliferation of gingival-fibroblasts, pulp-dental cells and human osteoblasts in culture, and to determine the physical, mechanical and biological properties of poly (methyl methacrylate) (PMMA) enriched with GO. Material and Methods: The GO was characterized with SEM. Cytotoxicity and cell proliferation were determined by the MTT bioassay. The physical mechanical tests (flexural strength and elastic modulus) were carried out with a universal testing machine. Sorption and solubility were determined by weighing before and after drying and immersion in water. Porosity was evaluated by visual inspection. Data were analyzed with Student's t-test and Tukey's posthoc ANOVA. Results: The GO has a heterogeneous morphology and a particle size of 66.67±64.76 µm. GO has a slight to no-cytotoxicity (>50-75% viability) at 1-30 days, and at 24 hours incubation of PMMA with GO significantly stimulates osteoblasts (45±8%, p<0.01). The physical and mechanical properties of PMMA with GO increase considerably without altering sorption, solubility and porosity. Conclusion: GO alone or with PMMA has an acceptable biocompatibility, could contribute to cell proliferation, cell regeneration and improve the physical mechanical properties of PMMA.

Objective: To determine the cytotoxicity and effects of graphene oxide (GO) on cellular proliferation of gingival-fibroblasts, pulpdental cells and human osteoblasts in culture, and to determine the physical, mechanical and biological properties of poly (methyl methacrylate) (PMMA) enriched with GO. Material and Methods: T he G O w as c haracterized with SEM. Cytotoxicity and cell proliferation were determined by the MTT bioassay. The physical-mechanical tests (flexural strength and elastic modulus) were carried out with a universal testing machine. Sorption and solubility were determined by weighing before and after drying and immersion in water. Porosity was evaluated by visual inspection. Data were analyzed with Student's t-test and Tukey's post-hoc ANOVA. Results: The GO has a heterogeneous morphology and a particle size of 66.67±64.76 ?m. GO has a slight to no-cytotoxicity (>50-75% viability) at 1-30 days, and at 24 hours incubation of PMMA with GO significantly stimulates osteoblasts (45±8%, p<0.01). The physical and mechanical properties of PMMA with GO increase considerably without altering sorption, solubility and porosity. Conclusion: GO alone or with PMMA has an acceptable biocompatibility, could contribute to cell proliferation, cell regeneration and improve the physical-mechanical properties of PMMA.

Biological and mechanical characterization of commercial and experimental periodontal surgical dressings

Abstract The objective of this study was to evaluate the biocompatibility and mechanical properties of two commercially available and one experimental periodontal dressing materials. The cytotoxicity of Periobond ® , Barricaid ® and one experimental periodontal dressing based on Exothane ® 8 monomer was tested on 3T3/NIH mouse fibroblast. Genotoxicity was assessed by micronuclei formation, and cell alterations were analyzed using light microscopy. Both biological assays were performed using the eluate obtained from specimens after 24, 72, or 168 hours of incubation. Mechanical characterization was assessed through the ultimate tensile strength and the water sorption and solubility tests. The significance level of α = 0.05 was used for all statistical analyses. All the materials promoted a cell viability lower than 60% in all evaluated times. In general, the cell viability was significantly reduced after 72 and 168h of specimens' incubation. Considering the factor material, there were not statistical differences in the cell viability (p = 0.156). The genotoxicity was not statistically significant among the groups in the different periods of time (p > 0.05). Differences in the ultimate tensile strength values were not statistically significant different among the groups (p = 0.125). Periobond ® showed the higher water sorption values (p < 0.001). Regarding solubility, there were no statistical differences between the groups (p = 0.098). All the periodontal dressing materials evaluated in this study exerted a cytotoxic effect against mouse fibroblasts, and their toxicity became more evident over time. Among the materials evaluated, the experimental light-cure type has shown overall similar properties to the commercial references.

Silver Diamine Fluoride versus Bioactive Giomer Light-Curing Varnish: An In Vitro Study on Caries Arrest

ABSTRACT Objective To compare the capacity of silver diamine fluoride (30%) and the bioactive giomer light-curing varnish for arresting ICDAS score 5 non-retentive caries lesions. Material and Methods An in vitro analytical study was conducted using 36 healthy primary teeth, in which a cavity was created, divided into 3 groups: control (distilled and deionized water), giomer-based light-curing varnish - Barrier Coat, and Silver Diamine Fluoride 30% - Cariestop (SDF). The samples were analyzed for mineral loss as measured by surface microhardness (SMH).The Knoop microhardness test was performed using the HVS-1000 microhardness tester. The data were compared by two-way analysis of variance - treatment and time (before and after treatment) followed by Tukey's post-test. The significance level adopted in all analyzes was 5%. Results The specimens treated with giomer showed higher SMH compared to the untreated group but were similar to those of the SDF group. The SDF group, on the other hand, showed no statistically significant difference from the control group (p=0.010). Conclusion The giomer varnish had a remineralizing effect on artificial dentinal caries.

Evaluation of bond strength of self-adhesive resin composite repairs / Avaliação da resistência de união de reparos com resina composta auto-adesiva

ABSTRACT Objective: To evaluate the bond strength of repairs with the self-adhering flowable composite Vertise Flow (Kerr) and a conventional composite resin Filtek Z350 (3M ESPE) subjected to different surface treatments. Methods: Forty specimens were divided into four groups: ZV (Filtek Z350 + Vertise Flow, without prior treatment); ZAV (Z350 + Vertise Flow with prior treatment with Single Bond Universal Adhesive System (3M ESPE)); ZAZ (Filtek Z350 + Filtek Z350 with prior treatment with Single Bond Universal Adhesive System (3M ESPE)); VV (Vertise Flow + Vertise Flow, without prior treatment). After 15 days of storage, the specimens were subjected to microtensile tests (Kratos IKCL3-USB, SP, Brazil), with speed of 0.5 mm/min and 20kg load. For statistical analysis, ANOVA with Tukey tests were used (p < 5%). Results: The mean values of the bond strength were highest respectively in the groups: ZV (36.07 ± 37.63); ZAZ (24.04 ± 28.51); VV (19.39 ± 28.24) and ZAV (16.06 ± 15.66). The bond strength of the repairs between the groups presented satisfactory results. Conclusion: The self-adhesive composite resin Vertise Flow seems to be a viable and fast alternative for composite resins repairs.

RESUMO Objetivos: Avaliar a resistência de união dos reparos com resina composta auto-adesiva Vertise Flow (Kerr) e uma resina composta convencional Filtek Z350 (3M ESPE) submetida à diferentes tratamentos de superfície. Métodos: Quarenta amostras foram divididas em quatro grupos: ZV (Filtek Z350 + Vertise Flow, sem tratamento prévio); ZAV (Z350 + Vertise Flow com tratamento prévio com Sistema Adesivo Universal Single Bond (3M ESPE)); ZAZ (Filtek Z350 + Filtek Z350 com tratamento prévio com Sistema Adesivo Universal Single Bond (3M ESPE)); VV (Vertise Flow + Vertise Flow, sem tratamento prévio). Após 15 dias de armazenamento, as amostras foram submetidas ao teste de microtração (Kratos IKCL3-USB, SP, Brasil), com velocidade de 0,5 mm / min e carga de 20kg.Para análise estatística, foram utilizados os testes ANOVA com Tukey (p <5%). Resultados: Os valores médios da resistência de união foram maiores, respectivamente, nos grupos: ZV (36,07 ± 37,63); ZAZ (24,04 ± 28,51); VV (19,39 ± 28,24) e ZAV (16,06 ± 15,66). A resistência de união dos reparos entre os grupos apresentou resultados satisfatórios. Conclusão: A resina composta auto-adesiva Vertise Flow parece ser uma alternativa viável e rápida para reparos em restaurações com resinas compostas.

Estudo comparativo da resistência mecânica da força de compressão entre biomateriais naturais, sintéticos e mistos / Comparative study of mechanical strength of compression between natural, synthetic and mixed biomaterials

As afecções ortopédicas com perda de tecido ósseo são um desafio tanto na medicina veterinária quanto na medicina humana. Portanto, não é raro ortopedistas se depararem com fraturas cominutivas irredutíveis de ossos longos, neoplasias ósseas ou não-uniões, que necessitam de procedimentos cirúrgicos reparadores, por meio da substituição de segmento ou preenchimento de falha óssea com o uso de biomateriais. Pretende-se com esta pesquisa avaliar e comparar a resistência mecânica entre biomateriais naturais, sintéticos e mistos. Foram utilizados sete grupos experimentais compostos por seis corpos de provas cada: Grupo 1 , tecido ósseo cortical de coelho (OSSO - controle); Grupo 2, cimento ósseo (CO); Grupo 3, cimento ósseo autoclavado (COA); Grupo 4, cimento ósseo e macrofragmento ósseo cortical de cão (COMaFO); Grupo 5, cimento ósseo e macrofragmento ósseo autoclavado de cortical de cão (COMaFOA); Grupo 6, cimento ósseo e microfragmento ósseo cortical de cão (COMiFO) e Grupo 7, cimento ósseo e microfragmento ósseo cortical de cão (COMiFOA). Os corpos de prova foram submetidos a ensaios mecânicos de compressão axial controlada em máquina universal de ensaio Emic®. O teste era interrompido quando ocorria queda brusca na curva do gráfico indicando falência da amostra. Em relação à Força máxima, os grupos COA, COMaFOA e COMiFOA não diferiram estatisticamente do grupo controle (OSSO; p>0,01). Já os grupos CO, COMaFO e COMiFO diferiram estatisticamente do grupo controle (OSSO; p<0,01). Quanto a rigidez relativa, os grupos COMaFOA e COMiFOA não diferiram estatisticamente do grupo controle (OSSO; p>0,01). Já os grupos CO, COA, COMaFO e COMiFO diferiram estatisticamente do grupo controle (OSSO; p<0,01). Comparando a deformação, os grupos COMaFo, COMaFOA e COMiFO não diferiram estatisticamente do grupo controle (OSSO; p>0,01). Já os grupos CO, COA e COMiFOA diferiram estatisticamente do grupo controle (OSSO; p<0,01). Conclui-se que apenas os grupos COMaFOA e COMiFOA apresentaram propriedades mecânicas muito semelhantes às do grupo controle (OSSO). Por isso, devido a essas características, esses dois biomateriais (COMaFOA e COMiFOA) seriam os mais indicados como substitutos na reparação de falhas ósseas.(AU)

The orthopedic diseases with bone loss are the challenge in both veterinary and human medicine. Therefore, the orthopedist commonly deal with irreducible comminuted fractures of long bones, bone tumors or non-unions, which require repairers surgical procedures, through the segment replacement or bone defect filling with biomaterials. The aim of this research is to evaluate and compare the mechanical strength of natural, synthetic and mixed biomaterials. Seven experimental groups of six test samples each were used: Group 1 rabbit cortical bone (BONE - control); Group 2, bone cement (CO); Group 3, bone cement autoclaved (COA); Group 4, bone cement and dog cortical bone macrofragment (COMaFO); Group 5, bone cement and bone autoclaved macrofragment dog cortical (COMaFOA); Group 6, bone cement and dog cortical bone microfragment (COMIFO) and Group 7, bone cement and dog cortical bone microfragment (COMiFOA). The specimens were subjected to axial compression mechanical tests controlled universal testing machine EMIC®. The test was stopped when there was sharp decline in the graph curve indicating failure of the sample. In relation to the maximum force, the COA groups COMaFOA and COMiFOA not statistically different from the control group (BONE; p> 0.01). Already the CO groups, COMaFO and COMIFO difeririram statistically the control group (BONE; p <0.01). The relative rigidity, the COMaFOA and COMiFOA groups did not differ statistically from the control group (BONE; p>0.01). Already the CO groups, COA, COMaFO and COMIFO differed significantly from the control group (BONE; p<0.01). Comparing the deformation, the COMaFo groups COMaFOA and COMIFO not statistically different from the control group (BONE; p>0.01). Already the CO groups, COA and COMiFOA differed significantly from the control group (BONE; p<0.01). It is concluded that only COMaFOA and COMiFOA groups showed very similar mechanical properties to the control group (BONE). Therefore, due to these characteristics, these two biomaterials (COMaFOA e COMiFOA) would be the most suitable as a substitute in the repair of bone defects.(AU)

Propriedades tensiométricas do peritônio da paca (Cuniculus paca) a fresco e conservado em glicerina 98 por cento / Tensiometer peritoneum properties of the paca (Cuniculus paca) fresh and preserved in glycerin 98 por cento

In constant searching for alternative biological material to perform implants and new options of experimental animal models, the objective of this investigation was to describe the mechanical properties of the peritoneum paca (Cuniculus paca Linnaeus, 1766) fresh and preserved in 98% glycerin. Samples of fresh and preserved in glycerin for periods of 30, 60 and 90 days were subjected to mechanical tests. Four adult animals, male or female, with mean body weight of eight kilograms, were used for collecting samples of the peritoneum. All tissues preserved in glycerin 98% showed a decrease in stiffness and increase in ductility and toughness. Considering the maximum force applied to the peritoneum, significant increase was observed in values (p<0.01) of samples stored for 60 and 90 days when compared to fresh material. In relation to the stretch variable, an increase was observed in all storage time of glycerin samples, verifying significant difference (p<0,01) when compared with the fresh samples. The variable area also showed significance (p <0.01) between the values of the fresh samples (5.40 mm²) and preserved in the glycerin by periods of 30 days (4.50 mm²), 60 days (9.00 mm²) and 90 days (7.20 mm²), thus indicating that the area of this membrane increased by 0.033 mm² per day. Generally, it was concluded that the 98% glycerin is a substance effective for the preservation of the peritoneum of the agouti paca, therefore improves its mechanical properties allowing the support membranes greater deformation forces. Thus, the results obtained in mechanical tests of the peritoneum of paca suggest its use as an alternative biological material.

Na busca constante, tanto de material biológico alternativo para a realização de implantes, quanto de novas opções de modelos de experimentação animal, o objetivo desta investigação foi descrever o comportamento mecânico do peritônio da paca (Cuniculus paca Linnaeus, 1766) a fresco e conservado em glicerina a 98%. Amostras frescas e conservadas em glicerina por períodos de 30, 60 e 90 dias foram submetidas a testes mecânicos de tração. Quatro animais adultos, três machos e uma fêmeas, com peso corporal médio de oito quilogramas, foram utilizados para colheita das amostras de peritônio. Todos os tecidos conservados em glicerina a 98% apresentaram diminuição na rigidez e aumento na ductibilidade e tenacidade. Considerando-se a força máxima aplicada ao peritônio, evidenciou-se aumento significativo nos valores (p<0,01) das amostras conservadas por 60 e 90 dias, quando comparado ao material a fresco. Com relação a variável alongamento, notou-se aumento nos valores relativos aos materiais em glicerina em todos os tempos de conservação, verificando-se diferença significativa (p<0,01) entre os valores das amostras a fresco. A variável área também se apresentou significativa (p<0,01) entre os valores das amostras a fresco (5,40 mm²) e os preservados em glicerina pelos períodos de 30 dias (4,50 mm²), 60 dias (9,00 mm²) e 90 dias (7,20 mm²), indicando assim, que a área desta membrana aumentou em 0,033 mm² por dia. Mediante os resultados observados, concluiu-se que a glicerina 98% é uma substância eficiente para a conservação do peritônio da paca, pois melhorou suas propriedades mecânicas permitindo que as membranas suportem maiores forças de deformação. Assim, os resultados obtidos nos ensaios mecânicos do peritônio da paca sugerem sua utilização como mais uma opção de material biológico.

Sistemas osso-implante ex vivo utilizando haste intramedular polimérica para imobilização de fraturas femorais em bovinos jovens / Ex vivo bone-implant systems using polymeric intramedullary nails for fixation of femoral fractures in young calves

O desenvolvimento de novos aparatos usando materiais disponíveis e de baixo custo pode ser uma alternativa viável para o tratamento cirúrgico de fraturas em ossos longos de bovinos. O objetivo deste estudo foi avaliar a resistência mecânica de fêmures de bovinos jovens com fratura diafiseal, imobilizados com hastes intramedulares bloqueadas, compostas por diferentes polímeros. Para tanto, testes físicos de compressão e flexão, por meio de uma máquina universal de ensaios foram realizados em quatro grupos distintos de seis fêmures obtidos de bovinos jovens. Em um dos grupos, os ossos foram mantidos íntegros (grupo controle), enquanto que os outros os ossos, foram fraturados e imobilizados com uma haste intramedular bloqueada, composta por polipropileno, poliacetal ou poliamida (uma para cada grupo). Independente do polímero utilizado, nenhuma das hastes estudadas ofereceu aos fêmures fraturados resistência comparável ao osso íntegro, quando consideradas em conjunto as forças de flexão e compressão. A concordância desses achados com resultados in vivo previamente publicados, demonstra que a metodologia utilizada para testes ex vivo pode ser útil na seleção de materiais mais resistentes para confecção de novos modelos.

The development of new devices using available and low cost materials may be an useful alternative for the treatment of long bone fractures in large animals. The aim of this study was to evaluate the mechanical strength of young bovine femur with diaphyseal fracture fixed with different polymeric intramedullary nails. Bending and compression tests using a universal machine were carried out in 4 distinct groups of 6 femurs from young calves. In one of the groups bones were intact while in the other three fractured bones were fixed using an intramedullary nail made of polypropylene, polyacetal or polyamide (one for each group). Considering bending and compression tests together, none of the used polymers offered strength to the fractured bones similar to the intact ones. The agreement of this findings with those from previous published in vivo results indicates that the employed ex vivo methods for mechanical assays may be useful in the search of stronger materials to be used in development of new devices.