Comparison of color stability, mechanical and chemical properties according to temporary crown resin type / 대한치과재료학회지

Objective of this study was to compare the color stability, mechanical and chemical properties of three different types of temporary crown resins. Commercially available powder-liquid (Group PL), light-cured (Group LC) and auto-mix syringe (Group AM) types' temporary crown resins were used as experimental groups for each of the evaluation. All the test groups were evaluated after 1 day and 7 days of immersion in various staining solutions. The colors of all groups before and after storage in the staining solutions were measured by a spectrophotometer based on CIE Lab system, and the color differences (ΔE(*)) thereby calculated. Micro hardness test was performed before water storage and aging after 7 days at 37 ℃. In addition, flexural strength, water sorption and solubility tests were performed according to international standard, ISO 10477. All experimental groups showed significant color change in staining solutions when compared to those stored in the control solution (distilled water) (p PL > LC (p<0.05). Water sorption and solubility increased in the following order: AM < PL < LC (p<0.05). The results of this study would provide useful information when choosing temporary crown resin types in various clinical situations.

Comparação in vitro da sorção e da solubilidade de quatro materiais restauradores provisórios em endodontia / In vitro comparison of the sorption and solubility properties of temporary restorative materials used in endodontics

Objetivo: Este estudo comparou as propriedades de sorção e solubilidade de materiais restauradores provisórios utilizados em endodontia. Material e método: Foram confeccionados 60 corpos de prova, divididos em quatro grupos: G1-IRM® (Dentsply), G2- Coltosol® (Coltene), G3- Riva Light Cure® (SDI), G4 Clip F® (Voco) e pesados após 24h em balança analítica de precisão. Após, foram imersas em água destilada por 12 dias e pesados novamente. Retornaram à estufa a 37 °C por 24h. Resultados: Apresentaram diferenças estatisticamente significativas entre os grupos para sorção e solubilidade. O grupo G4 apresentou menor grau de sorção com diferença estatística dos demais grupos (0,0000087). Os níveis de sorção, encontrados nos grupos G3 (0,0000313) e G1 (0,0000493), apresentam- -se estatisticamente semelhantes entre si e o G2 (0,0000573) foi estatisticamente semelhante ao G1(0,0000493). Quanto à solubilidade, G1 (0,0000107) apresentou o menor nível com diferença estatística em relação aos demais grupos. Os valores de solubilidade, em ordem crescente, foram verificados respectivamente nos grupos G4 (-0,0000213), G3 (-0,000064) e G2 (-0,0002693). Conclusões: 1. Materiais provisórios fotoativados apresentaram os menores resultados quanto à sorção de água; 2. Compostos à base de óxido de zinco e eugenol apresentaram o menor nível de solubilidade comparado com todos os outros materiais provisórios e 3 - compostos livres de eugenol de uso imediato obtiveram os maiores valores tanto de sorção quanto de solubilidade.

Objective: This study compared the sorption and solubility properties of temporary restorative materials used in endodontics. Material and method: 60 specimens were divided into four groups: G1-IRM® (Dentsply), G2-Coltosol® (Coltene), G3-Riva Light Cure® (SDI), G4 Clip F® ) and weighed after 24 hours in precision analytical balance scale. Afterwards, they were immersed in distilled water for 12 days and weighed again. They returned to the stove at 37 ° C for 24 hours. Results: There were statistically significant differences between the groups for sorption and solubility. The G4 group presented lower degree of sorption with statistical difference of the other groups (0.0000087). The sorption levels, found in groups G3 (0.0000313) and G1 (0.0000493), were statistically similar to each other and G2 (0.0000573) was statistically similar to G1 (0.0000493). Regarding solubility, G1 (0.0000107) presented the lowest level with statistical difference in relation to the other groups. The solubility values, in ascending order, were respectively verified in groups G4 (-0.0000213), G3 (-0.000064) and G2 (-0.0002693). Conclusion: 1. Temporary photoactivated materials presented the lowest results regarding sorption of water; 2. Compounds based on zinc oxide and eugenol showed the lowest level of solubility compared to all other provisional materials and 3. eugenolfree compounds of immediate use obtained the highest values of both sorption and solubility.

Effect of Acidic Solutions on the Surface Degradation of a Micro-Hybrid Composite Resin

Composite resins may undergo wear by the action of chemical substances (e.g., saliva, alcohol, bacterial acids) of the oral environment, which may affect the material's structure and surface properties. This study evaluated the effect of acidic substances on the surface properties of a micro-hybrid composite resin (Filtek Z-250). Eighty specimens were prepared, and baseline hardness and surface roughness (KMN0 and Ra0, respectively) were measured. The specimens were subjected to sorption (SO) and solubility (SL) tests according to ISO 4049:2009, but using different storage solutions: deionized water; 75/25 vol% ethanol/water solution; lactic acid; propionic acid; and acetic acid. The acids were used in two concentrations: PA and 0.02 N. pH was measured for all solutions and final hardness (KMN1) and surface roughness (Ra1) were measured. Data were analyzed with paired t-tests and one-way ANOVA and Tukey's test (a=5%). All solutions decreased hardness and increased the Ra values, except for the specimens stored in water and 0.02 N lactic acid, which maintained the hardness. All solutions produced similar SO and SL phenomena, except for the 0.02 N lactic acid, which caused lower solubility than the other solutions. Ethanol showed the highest pH (6.6) and the 0.02 N lactic acid the lowest one (2.5). The solutions affected negatively the surface properties of the composite resin; in addition, an acidic pH did not seem to be a significant factor that intensifies the surface degradation phenomena.

Resinas compostas podem sofrer desgaste pela ação de substâncias químicas (saliva, álcool, ácidos bacterianos) presentes no ambiente oral, que podem afetar a estrutura e as propriedades superficiais do material. Assim, este estudo avaliou o efeito de substâncias ácidas nas propriedades superficiais de uma resina composta micro-híbrida (Filtek Z-250). Oitenta espécimes foram preparados e mensurados quanto à dureza e rugosidade superficial iniciais (KMN0 e Ra0, respectivamente). Os espécimes foram submetidos a testes de sorção (SO) e solubilidade (SL) de acordo com a ISO 4049:2009, porém usando diferentes soluções de armazenamento: água deionizada, solução etanol/água 75/25% em volume, ácido lático, ácido propiônico e ácido acético. Os ácidos foram utilizados em duas concentrações: PA e 0,02 N. O pH foi mensurado para todas as soluções e a dureza e rugosidade superficial finais (KMN1 e Ra1, respectivamente) foram mensuradas. Os dados foram analisados com testes t-pareado e ANOVA a um fator, e teste de Tukey (p<0,05). Todas as soluções reduziram a dureza e aumentaram os valores de Ra, exceto para os espécimes armazenados em água e ácido lático 0,02 N, que mantiveram a dureza. Todas as soluções produziram fenômenos de SO e SL similares, exceto o ácido lático 0,02 N, que causou menor solubilidade do que as outras soluções. Etanol mostrou o maior pH (6,6) e o ácido lático 0,02 N o menor deles (2,5). As soluções afetaram negativamente as propriedades superficiais da resina composta; além disso, um pH ácido não parece ser um fator significante para intensificar os fenômenos de degradação superficial.

Influence of various metal oxides on mechanical and physical properties of heat-cured polymethyl methacrylate denture base resins

PURPOSE: To evaluate the effect of various metal oxides on impact strength (IS), fracture toughness (FT), water sorption (WSP) and solubility (WSL) of heat-cured acrylic resin. MATERIALS AND METHODS: Fifty acrylic resin specimens were fabricated for each test and divided into five groups. Group 1 was the control group and Group 2, 3, 4 and 5 (test groups) included a mixture of 1% TiO2 and 1% ZrO2, 2% Al2O3, 2% TiO2, and 2% ZrO2 by volume, respectively. Rectangular unnotched specimens (50 mm x 6.0 mm x 4.0 mm) were fabricated and droptower impact testing machine was used to determine IS. For FT, compact test specimens were fabricated and tests were done with a universal testing machine with a cross-head speed of 5 mm/min. For WSP and WSL, discshaped specimens were fabricated and tests were performed in accordance to ISO 1567. ANOVA and Kruskal-Wallis tests were used for statistical analyses. RESULTS: IS and FT values were significantly higher and WSP and WSL values were significantly lower in test groups than in control group (P<.05). Group 5 had significantly higher IS and FT values and significantly lower WSP values than other groups (P<.05) and provided 40% and 30% increase in IS and FT, respectively, compared to control group. Significantly lower WSL values were detected for Group 2 and 5 (P<.05). CONCLUSION: Modification of heat-cured acrylic resin with metal oxides, especially with ZrO2, may be useful in preventing denture fractures and undesirable physical changes resulting from oral fluids clinically.

Efeito do tratamento térmico sobre a sorção e solubilidade, tenacidade à fratura e grau de conversão de compósitos restauradores diretos / Effect of post-curing heat cured treatment in sorption and solubility, fracture toughness and degree of conversion of direct composites

O tratamento térmico em compósitos restauradores diretos foi realizado a fim de verificar a influência sobre algumas propriedades, tais como a sorção, solubilidade, tenacidade à fratura e grau de conversão. Foram utilizados três compósitos: um nanoparticulado, um microhíbrido e um microparticulado. Duas fontes de luz (Halógena e LED) e dois períodos (48h e 28dias) de armazenagem, com exceção da solubilidade. O tratamento térmico foi realizado em estufa convencional (170o C por 5min), sendo metade dos corpos de prova (cps) tratados e a outra, apenas fotoativada.Para sorção e solubilidade, foram confeccionados 60 cps de acordo com os fatores analisados (n=5) em uma matriz metálica circular de dimensões 15 mm x1 mm. Para o cálculo da sorção e solubilidade, os cps foram pesados em uma Balança Analítica,inicialmente após a confecção do cp, 1hora, 24h, 48h, 7d, 14, 21 e 28d, a fim de estabelecer Massa Inicial (Mi) Massa absorvida (Ma) e Massa dessecada (Md). Para a tenacidade à fratura, foram confeccionados 240 cps de acordo com os fatores analisados (n=10) em uma matriz metálica de dimensões internas 25 mm x 5mm x 2,8 mm. O método utilizado foi o Single Edge Notch-Beam(SENB), com um entalhe de 2,3 mm posicionado no centro da matriz. Os cps eram levados à máquina universal para o ensaio de flexão e, após a ruptura, as superfícies de fratura eram analisadas no estereomicroscópio, para, em seguida, obter as imagens e calcular as dimensões do cps para inserir naequação da tenacidade à fratura.Já para o grau de conversão foram confeccionados 36 cps em uma matriz de acetato circular de 15 mm x 1 mm, posicionados entre duas lâminas microscópicas (n=3). O cálculo do grau de conversão foi determinado por espectroscopia no infravermelho (FTIR).Em geral, os estudos apresentaram uma influência significante do tratamento térmico...

The post-curing heat treatment in direct composite treatment was done to verify the influence on some properties like sorption, solubility, fracture toughness and the degree of conversion. During the referred study it was used three composites: nanoparticle, a microhybrid and a microfill. Two sources of light (Halogen and LED) and two periods (48 hours and 28 days) for each one, but not to solubility. The postcuringwas done in dry heat sterilizer of 170º C for five minutes for, half of the test samples (TS) were treated and the other half were only photoactivated. It was made 60 TS to sorption and solubility according to the analyzed factors (n=5) in a 15mm x 1mm round metal matrix. To calculate sorption and solubility the TS were weighted in a analytical balance, right after the beginning of the production in 1 hour, 24 hours, 7days, 14 days, 21 days and 28 days respectively in order to establish the initial absorbed mass (Mi), the absorbed mass (Ma) and the desiccated mass (Md ). It was produced 240 TS to the fracture toughness according to factors (n=10) in a 25mm x 5mm x 2,8mm in metallic matrix. The Single Edge Notch-Beam (SENB), was the used method during this study with a notch of 2,3mm placed in the center of the matrix. The TS were taken to a universal machine to flexural test so after the rupture referred surface fractures were analyzed in a stereomicroscope and then it was possible to get the images to calculate the size of the TS to insert the calculus of the fracture toughness...