Your browser doesn't support javascript.
loading
Mostrar: 20 | 50 | 100
Resultados 1 - 2 de 2
Filtrar
Adicionar filtros








Intervalo de ano
1.
Eng. sanit. ambient ; 26(6): 1015-1024, nov.-dez. 2021. tab, graf
Artigo em Português | LILACS-Express | LILACS | ID: biblio-1350709

RESUMO

RESUMO Diversos trabalhos têm mostrado a formação de lodo granular aeróbio em reatores nos quais são impostas elevadas velocidades de sedimentação, da ordem de 10 a 12 m.h−1. Aparentemente, quando a velocidade de sedimentação é inferior a 3,8 m.h−1, a fração de lodo floculado é predominante, visto que o lodo suspenso não é eliminado de forma efetiva do reator. Outros estudos, entretanto, mostram a formação de lodos granulares aeróbios para velocidades menores que essa, apontando a possibilidade da formação desse tipo de biomassa em velocidades ainda menores. Assim, este trabalho avaliou a formação desse tipo de lodo em reatores que tratam esgoto sanitário, com relação altura/diâmetro unitária, para velocidades de sedimentação de 1,8 e 1,2 m.h−1, verificando as eficiências de remoção de matéria orgânica e nitrogênio. Os resultados obtidos indicaram que é possível formar lodo aeróbio granular para a faixa de velocidade de estudo, porém com baixa estabilidade estrutural para diâmetros de 1,2 mm ou mais. Essa instabilidade dos grânulos contribui para a baixa eficiência de remoção de matéria orgânica e nitrogênio nos reatores.


ABSTRACT Several studies have shown the formation of aerobic granular sludge in reactors where high sedimentation rates are imposed, varying from 10 to 12 m.h−1. Apparently, when the settling velocity is less than 3.8 m.h−1, the fraction of flocculated sludge is predominant, since the suspended sludge is not effectively eliminated from the reactor. Other studies, however, show the formation of aerobic granular sludge at velocities lower than this, pointing to the possibility of formation of this type of biomass at even lower speeds. Thus, this work evaluated the efficacy of this type of sludge in reactors treating sewage, with H/D ratio (height/diameter), for sedimentation velocities of 1.8 and 1.2 mh−1, verifying the efficiencies of organic matter and nitrogen. The results indicated that it is possible to form aerobic granular sludge for the study velocity range, but with low structural stability from diameters of approximately 1.2 mm. This instability of the granules contributes to the low efficiency of removal of organic matter and nitrogen in the reactors.

2.
Eng. sanit. ambient ; 17(1): 25-32, jan.-mar. 2012. ilus, tab
Artigo em Português | LILACS | ID: lil-646791

RESUMO

A adição de polieletrólito ao processo de floculação no tratamento físico-químico por coagulação-floculação-sedimentação de efluentes tem sido uma alternativa para a obtenção de clarificados de boa qualidade em menor tempo devido ao aumento da velocidade de sedimentação. Deste modo, este artigo, objetivou determinar as inter-relações entre as variáveis pH, gradiente de floculação, dosagem de ferro e tipo de polieletrólito e avaliar o efeito desta adição na remoção de cor, DQO e turbidez no pós-tratamento do lixiviado submetido a tratamento biolõgico. Através do uso da técnica de planejamento e analisando-se os resultados obtidos, pôde-se verificar que o polímero de carga catiônica apresentou-se como o mais eficiente, obtendo remoções de até 97,70% para cor verdadeira, 81,52% para DQO e 92,18% para turbidez.


The addition of polyelectrolyte flocculation process in the physical-chemical treatment by coagulation-flocculation-sedimentation effluent has been an alternative to obtain clarification of good quality in less time due to increased sedimentation rate. Thus, this article aimed to determine the interrelationships between the pH gradient, flocculation, iron dosage and type of polyelectrolyte and evaluate the effect of this addition on color removal, COD and turbidity in the post-treatment of the leachate subjected to pretreatment biological. Through the use of technical planning and analyzing the results, it was found that the polymer cationic charge introduced himself as the most efficient, achieving removals of up to 97.70% for true color, 81.52% for COD and 92.18% for turbidity.

SELEÇÃO DE REFERÊNCIAS
DETALHE DA PESQUISA