RESUMO
Objective@#To investigate the antibacterial properties, biocompatibility and mechanical properties of Cu-ZnO-loaded dental veneering porcelain to provide an experimental basis for the development of new dental veneering porcelain. @*Methods@#Cu-ZnO nanoparticles were added to IPS E.max Ceram for restorative veneer porcelain at different mass percentages of 0 wt%, 1 wt%, 2 wt%, 3 wt%, 4 wt%, 5 wt%, and 6 wt% using ball milling in ceramic powder. A cylindrical specimen with a diameter of 20 mm and a thickness of 2 mm was prepared by high-temperature sintering. Scanning electron microscopy was used to observe the surface morphologies of nano-Cu-ZnO and the specimens. The antibacterial effect of Escherichia coli (E. coli) was quantitatively studied by the plate colony counting method. The CCK-8 method was used to evaluate in vitro the cytotoxicity of the tested piece to mouse fibroblasts (L929). Live and dead cells were observed by fluorescence microscopy. The mechanical properties of modified IPS E. Max Ceram veneering porcelain were tested by a three-point bending strength test. @* Results @# Under the scanning electron microscope, Cu-ZnO appears with a block-like structure and can be seen dispersed in the veneering porcelain. When the nano Cu-ZnO loading was 1 wt%, 2 wt%, 3 wt%, and 4 wt%, the antibacterial rates of the specimens were 24.85%, 67.94%, 96.92%, and 99.99%, respectively, and the difference between the experimental groups and the control group was statistically significant (F = 23.308,P = 0.001). The relative growth rate of each group was greater than 80% after coculture with mouse fibroblast cells (L929) for 1 day and 3 days, and there was no significant difference between the groups. The morphology of L929 cells was normal after coculture for 24 hours. With the increase in the Cu-ZnO concentration, the flexural strength of the specimen exhibited an increasing trend followed by a decreasing trend. The bending strength of the specimen loaded with 3 wt% nano Cu-ZnO reached the maximum value (84.728 ± 6.82) MPa, and there was no statistically significant difference between groups (F = 0.633,P = 0.702).@*Conclusion@#The antibacterial rate of IPS E. max Ceram veneering porcelain loaded with 3 wt% nano Cu-ZnO was more than 96% against E. coli after high-temperature sintering at 750 ℃. The bending strength reached the maximum (84.728 ± 6.82) MPa, and there was no obvious cytotoxicity.
RESUMO
The objective of this study was to characterize the mechanical properties of Y2O3-containing glass infiltrated ceramic core material, which was made by pressureless powder packing method. A pure alumina powder with a grain size of about 4micrometer was packed without pressure is silicon mold to form a bar shaped sample, and applied PVA solution as a binder. Samples were sinterd at 1350degrees C for 1 hour. After cooling, Y2O3-containing glass (SiO2, Y2O3, B2O3, Al2O3, ect) was infiltrated to the sinterd samples at 1300degrees C for 2 hours and cooled. Six different proportions Y2O3 of were used to know the effect of the mismatch of the thermal expansion coefficient between alumina powder and glass. The samples were ground to 3x3x30 mm size and polished with 1microneter diamond paste. Flexural strength, fracture toughness, hardness and other physical properties were obtained, and the fractured surface was examined with SEM and EPMA. Ten samples of each group were tested and compared with In-Ceram(TM) core materials of same size made in dental laboratory. The results were as follows : 1. The flexural strengths of group 1 and 3 were significantly not different with that of In-Ceram, but other experimental groups were lower than In-Ceram. 2. The shrinkage rate of samples was 0.42% after first firing, and 0.45% after glass infiltration. Total shrinkage rate was 0.87%. 3. After first firing, porosity rate of experimental groups was 50%, compared with 22.25% of In-Ceram. After glass infiltration, porosity rate of experimental groups was 2%, and 1% in In-Ceram. 4. There was no statistical difference in hardness between two materials tested, but in fracture toughness, group 2 and 3 were higher than In-Ceram. 5. The thermal expansion coefficients of experimental groups were varied to 4.51~5.35x10-6/degrees C according to glass composition, also the flexural strengths of samples were varied. 6. In a view of SEM, many microparticles about 0.5microneter diameter and 4microneter diameter were observed in In-Ceram. But in experimental group, the size of most particles was about 4microneter, and a little microparticles was observed. The results obtained in this study showed that the mismatch of the thermal expansion coefficients between alumina powder and infiltrated glass affect the flexural strength of alumin/glass composite. The Y2O3-containing glass infiltrated ceramic core made by powder packing method will takes less time and cost with sufficient flexural strength similar to all ceramic crown made with slip casting technique.