Research progress on the design of fixed implant-supported prostheses in edentulous jaws / 口腔疾病防治

@#With the aging of the population and the increase in the number of edentulous patients, implant-supported fixed restorations have become more prevalent in clinical treatment. It is necessary to assess the patient's remaining bone and occlusal situation correctly; the upper jaw usually needs 6 to 8 implants, whereas the lower jaw needs 4 to 6 implants. Patients with severe alveolar bone atrophy can adopt the "all-on-4/6" treatment plan, short implants, and zygomatic and pterygomaxillary implants to avoid complex bone grafting and remain cautious when the surgical procedures require more surgical experience. According to the repair methods, the superstructure can be divided into one-piece repair and segmental repair. One-piece repair has a lower implant number, flexible location, and reasonable stress distribution but a high maintenance cost. Sectional repair easily achieves passive placement, convenient cleaning, and maintenance in the late stages, but implants need quantity and high requirements for alveolar bone. However, the requirements for alveolar bone and implant number are high. Mutually protected occlusion with minimal or no cantilever on provisional prosthesis is recommended.

Development of tilted implant for free end of maxillary posterior teeth / 华西口腔医学杂志

Vertical bone insufficiency in the maxillary posterior teeth is a common clinical situation. At present, the bone insufficiency in the maxillary posterior teeth is mainly overcome by bone grafting through maxillary sinus floor elevation. Compared with traditional axial implantation, tilted implantation can better avoid bone grafting, reduce complications, shorten the treatment cycle, reduce the treatment cost for patients, and gradually be promoted in clinical settings. This article reviews the concept, biomechanics, clinical evaluation, and digital trend of tilted implants of maxillary posterior teeth.

Maxillary complete denture and mandibular All-on-4 implant restoration considering maintenance: a case report

In the case of edentulous patients, the total amount of occlusal force is dispersed by the keratinized gingiva during mastication, in result, causing lower masticatory and chewing efficiency. In particular, the mandibular area has more side effects such as pain than the maxilla has. It gets worse when the patient has more absorption of alveolar bone, but the implant treatment is often interrupted due to the existence of the inferior alveolar nerve. In this case, a patient treated with the all-on-4 method by placing the implant in the anterior part of mandible and with the conventional complete denture for the maxilla has maintained without complications and was satisfied with the restoration both functionally and esthetically.

Application of digital implant system on implant treatment with “all-on-4” concept / 대한치과보철학회지

Recently, digital implant systems are expanding its influence in dental area. Due to technical improvement, they jumped over their limits nowadays. We can use these newest systems to treat edentulous patient, from implant surgery to fabrication of prosthesis. In this case, The patient was a fifty years old female. She had a full edentulous ridge on mandible and wanted to reconstruct occlusion with using implants. We planned to use digital implant system with “all-on-4” concept on mandible and produced surgical guide for flapless implant surgery. After the surgery, we tried to fabricate full arch prosthesis just using a digital devices and confirmed satisfying result.

Zirconia ceramic fixed dental prosthesis with all-on-4 concept implants for irradiated maxilla: A case report / 대한치과보철학회지

The implant-supported fixed dental prosthesis in irradiated maxilla needs meticulous treatment planning due to low bone healing capacity. All-on-4 concept implantation can reduce the number of implants to be placed avoiding bone grafting procedure. Conventionally, prefabricated angled abutments for tilted implants have been used. However, in this case, it was replaced with computer-aided design and computer-aided manufacturing (CAD/CAM) abutment. This case report described all-on-4 concept implantation and fabrication of CAD/CAM zirconia fixed dental prostheses using CAD/CAM titanium abutments.