Your browser doesn't support javascript.
loading
Influência de propriedades físico químicas dos materiais resinosos e da técnica de inserção na adaptação marginal de restaurações classe II / Influence of physicochemical properties of resin materials and insertion technique on marginal adaptation of class II restorations
Rio de Janeiro; s.n; 2013. 95 p. ilus, tab, graf.
Thesis in Portuguese | LILACS, BBO | ID: biblio-867233
RESUMO
A contração de polimerização das resinas compostas é uma característica indesejável que compromete a integridade da interface dente/restauração. O objetivo deste estudo foi avaliar in vitro a influência de diferentes materiais usados em restaurações classe II de resina composta, quanto ao grau de conversão, tensão de contração, resistência a flexão, módulo de elasticidade e formação de fenda marginal. Foram realizados preparos classe II com dimensões de 4x4x2mm em terceiros molares recém-extraídos para a avaliação da formação de fenda marginal. As cavidades foram niveladas com cimento de ionômero de vidro Riva Light Cure (SDI) (CIV), resina de baixa contração SureFil®SDR™ (Dentsply) (SDR), resina flow Filtek™Z350Flow (3M/ESPE) (Z350F) e resina composta Filtek™P90 (3M/ESPE) (P90). As restaurações (n=3) foram avaliadas com lupa estereoscópica. A resistência a flexão foi avaliada por meio de ensaio de flexão em três pontos. Para este ensaio foram confeccionados dez corpos de prova (n=10) de cada material com dimensões de 10x2x1mm. Para o teste de tensão de contração foram utilizados cilindros de polimetacrilato com 5 mm de diâmetro e 13 ou 28mm de comprimento. Os bastões foram fixados na EMIC com um espaço de 2mm entre eles, onde os materiais foram inseridos. Foram realizadas cinco repetições para cada grupo (n=5) e a tensão proveniente da contração foi medida por até 10 minutos após o início da fotopolimerização. O Grau de Conversão (GC) foi determinado por espectroscopia no infravermelho com transformada de Fourier (FTIR). Os resultados foram tratados estatisticamente por análise de variância (ANOVA) e Teste de Tukey (p<0,05). Fenda marginal Z350F = CIV > SDR = P90. Tensão de contração Z350F > SDR > CIV = P90. Resistência a flexão P90 > SDR = Z350F > CIV. Módulo de Elasticidade P90 > CIV = SDR = Z350F. GC Z350F = SDR > P90 > CIV.

Conclusões:

existe correlação entre a formação de fenda marginal e as propriedades físico químicas ...
ABSTRACT
The shrinkage of composite resin polymerization is an undesirable characteristic that compromises the integrity of the tooth / restoration interface. The aim of this study was to evaluate in vitro the influence of different materials used in composite resin class II restorations in terms of contraction stress, flexural strength, degree of conversion and marginal gap formation. Class II preparation were performed with 4x4x2mm dimensions in third molars freshly extracted for the evaliation of marginal gap formation. The cavities were filled with Riva Light Cure (SDI) glass ionomer cement (CIV), SureFil ® SDR ™ (Dentsply) low shrinkage resin (SDR), Filtek ™ Z350Flow (3M/ESPE) flowable composite (Z350F) and Filtek ™ P90 (3M/ESPE) composite resin (P90). The restorations (n = 3) were evaluated with magnifying stereoscopic. The flexural strength was assessed by means of three point bending test. For this test ten specimens (n = 10) of each material were made, each with 10x2x1mm dimensions. For the shrinkage stress test polymethacrylate cylinders with 5 mm in diameter and 13 or 28mm in length were used. Bats were attached to the EMIC with a 2mm space between them, where the materials were inserted. The test were repeated five times for each group (n = 5) and the contraction stress was measured for up to 10 minutes after initiation of photopolymerization. The Degree of Conversion (DC) was determined by Fourier transform infrared (FTIR). The results were statistically analyzed by the variance analysis (ANOVA) and Tukey test (p <0.05). Marginal gap Z350F = CIV > SDR = P90. Contraction stress Z350F > SDR> CIV = P90. Flexural strength P90 > SDR = Z350F > CIV. Elasticity Modulus P90 > CIV = SDR = Z350F. DC Z350F = SDR > P90 > CIV.

Conclusion:

There is a correlation between formation of marginal gap and physicochemical properties of the materials tested whereas low shrinkage resins provided better marginal ...
Subject(s)

Full text: Available Index: LILACS (Americas) Main subject: Dental Marginal Adaptation / Composite Resins / Dentistry, Operative / Chemical Phenomena Limits: Humans Country/Region as subject: South America / Brazil Language: Portuguese Year: 2013 Type: Thesis

Similar

MEDLINE

...
LILACS

LIS

Full text: Available Index: LILACS (Americas) Main subject: Dental Marginal Adaptation / Composite Resins / Dentistry, Operative / Chemical Phenomena Limits: Humans Country/Region as subject: South America / Brazil Language: Portuguese Year: 2013 Type: Thesis