How Plasmon Ag Nanoparticles can Enhance the Power Performance of a Thermoelectric Generator.

The development of wearable thermoelectric generators (wTEG) represents a promising strategy to replace batteries and supercapacitors required to supply electrical energy for portable electronic devices. However, the main drawback of wTEGs is that the thermal gradient between the skin and the ambient is minimal, reducing the power output produced by the generator. Therefore, it is necessary to improve the thermal management of wTEG in order to increase its efficiency. This work deals with the preparation of a thermoelectric generator that harnesses the plasmonic heating effect to enhance the thermal gradient of the final device. The thermoelectric layer is created through the in situ polymerization of terthiophene (3T) within a polyurethane matrix, utilizing silver (Ag) (I) and copper (II) perchlorate as oxidants. The plasmonic film, composed of Ag-NP (nanoparticles), is formed via photocatalytic reduction of silver nitrate in the presence of titanium oxide. These layers are then meticulously assembled to yield the hybrid plasmonic/thermoelectric generator.

Protocol for the synthesis of perovskite nanocrystal thin films via in situ crystallization method.

The field of halide perovskites currently faces the challenge of finding an efficient approach for producing highly efficient and stable perovskite nanocrystals (PNCs). Here, we present a protocol for the annealing-free and antisolvent-free synthesis of PNCs. We describe the steps for preparing the PNCs precursor solutions. We then detail the procedures to control crucial processing parameters, such as the role of precursor concentration and the creation of humidity-controlled chambers, which allow achieving precise control over the final nanocrystals size. For complete details on the use and execution of this protocol, please refer to Noguera-Gómez et al.1.

Pressure-Induced Phase Transition versus Amorphization in Hybrid Methylammonium Lead Bromide Perovskite.

The crystal structure of the CH3NH3PbBr3 perovskite has been investigated under high-pressure conditions by synchrotron-based powder X-ray diffraction. We found that after the previously reported phase transitions in CH3NH3PbBr3 (Pm3̅m→Im3̅→Pmn21), which occur below 2 GPa, there is a third transition to a crystalline phase at 4.6 GPa. This transition is reported here for the first time contradicting previous studies, which reported amorphization of CH3NH3PbBr3 between 2.3 and 4.6 GPa. Our X-ray diffraction measurements show that CH3NH3PbBr3 remains crystalline up to at least 7.6 GPa, the highest pressure covered by experiments. The new high-pressure phase is also described by the space group Pmn21; however, the transition involves abrupt changes in the unit-cell parameters and a 3% decrease of the unit-cell volume. Our conclusions are confirmed by optical-absorption experiments, by visual observations, and by the fact that pressure-induced changes up to 10 GPa are reversible. The optical studies also allow for the determination of the pressure dependence of the band-gap energy, which is discussed using the structural information obtained from X-ray diffraction.

Reassigning the Pressure-Induced Phase Transitions of Methylammonium Lead Bromide Perovskite.

The high-pressure crystal structure evolution of CH3NH3PbBr3 (MAPbBr3) perovskite has been investigated by single-crystal X-ray diffraction and synchrotron-based powder X-ray diffraction. Single-crystal X-ray diffraction reveals that the crystal structure of MAPbBr3 undergoes two phase transitions following the space-group sequence: Pm3̅m → Im3̅ → Pmn21, unveiling the occurrence of a nonpolar/polar transition (Im3̅ → Pmn21). The transitions take place at around 0.8 and 1.8 GPa, respectively. This result contradicts the previously reported phase transition sequence: Pm3̅m → Im3̅ →Pnma. In this work, the crystal structures of each of the three phases are determined from single-crystal X-ray diffraction analysis, which is later supported by Rietveld refinement of powder X-ray diffraction patterns. The pressure dependence of the crystal lattice parameters and unit-cell volumes are determined from the two aforementioned techniques, as well as the bulk moduli for each phase. The bandgap behavior of MAPbBr3 has been studied up to around 4 GPa, by means of single-crystal optical absorption experiments. The evolution of the bandgap has been well explained using the pressure dependence of the Pb-Br bond distance and Pb-Br-Pb angles as determined from single-crystal X-ray diffraction experiments.

Self-Assembly of CsPbBr3 Perovskites in Micropatterned Polymeric Surfaces: Toward Luminescent Materials with Self-Cleaning Properties.

In this work, we present a series of porous, honeycomb-patterned polymer films containing CsPbBr3 perovskite nanocrystals as light emitters prepared by the breath figure approach. Microscopy analysis of the topography and composition of the material evidence that the CsPbBr3 nanocrystals are homogeneously distributed within the polymer matrix but preferably confined inside the pores due to the fabrication process. The optical properties of the CsPbBr3 nanocrystals remain unaltered after the film formation, proving that they are stable inside the polystyrene matrix, which protects them from degradation by environmental factors. Moreover, these surfaces present highly hydrophobic behavior due to their high porosity and defined micropatterning, which is in agreement with the Cassie-Baxter model. This is evidenced by performing a proof-of-concept coating on top of 3D-printed LED lenses, conferring the material with self-cleaning properties, while the CsPbBr3 nanocrystals embedded inside the polymeric matrix maintain their luminescent behavior.

Two-Dimensional Indium Selenide for Sulphur Vapour Sensing Applications.

Surface-to-volume ratio in two-dimensional (2D) materials highlights among their characteristics as an inherent and intrinsic advantage taking into account their strong sensitivity to surface effects. For this reason, we have proposed in this work micromechanically exfoliated 2D nanosheets of InSe as an optical vapour sensor. As a proof of concept, we used 2-mercaptoethanol as the chemical analyte in vapour phase to monitor the change of the InSe photoluminescence (PL) before and after exposure to the analyte. For short vapour exposure times (at low analyte concentration), we found a PL enhancement of InSe nanosheets attributed to the surface localization of Se defects. For long vapour exposure times (or higher concentrations) a PL reduction is observed, probably due to the diffusion of molecules within the nanosheet. These results confirm the capability of 2D InSe as a photoluminescent sensor of vapours, because of its sensitivity to surface passivation or volume diffusion of molecules.

Ligand-Length Modification in CsPbBr3 Perovskite Nanocrystals and Bilayers with PbS Quantum Dots for Improved Photodetection Performance.

Nanocrystals surface chemistry engineering offers a direct approach to tune charge carrier dynamics in nanocrystals-based photodetectors. For this purpose, we have investigated the effects of altering the surface chemistry of thin films of CsPbBr3 perovskite nanocrystals produced by the doctor blading technique, via solid state ligand-exchange using 3-mercaptopropionic acid (MPA). The electrical and electro-optical properties of photovoltaic and photoconductor devices were improved after the MPA ligand exchange, mainly because of a mobility increase up to 5 × 10-3 cm 2 / Vs . The same technology was developed to build a tandem photovoltaic device based on a bilayer of PbS quantum dots (QDs) and CsPbBr3 perovskite nanocrystals. Here, the ligand exchange was successfully carried out in a single step after the deposition of these two layers. The photodetector device showed responsivities around 40 and 20 mA/W at visible and near infrared wavelengths, respectively. This strategy can be of interest for future visible-NIR cameras, optical sensors, or receivers in photonic devices for future Internet-of-Things technology.

Enhancing the photocatalytic properties of PbS QD solids: the ligand exchange approach.

Surface engineering of nanomaterials is a promising tool towards the design of new materials for conversion of solar energy into chemical energy. In this work, we examine the influence of ligand exchange on the photocatalytic performance of solution-processed PbS films. We test different ligands such as oleylamine (OAm), 1,2-ethanedithiol (EDT), 3-mercaptopropionic acid (MPA) and tetrabutylammonium iodide (TBAI). The study demonstrates that PbS films capped with MPA and EDT exhibit 3.5-fold enhanced photocatalytic performance for the photodecomposition of methyl orange upon sunlight exposure. Both band energy alignment and charge carrier transport have a strong impact on the generation of reactive oxygen species (ROS), which play a key role in the photodecomposition process. Moreover, the stability and reusability of the photocatalysts are clearly improved after ligand exchange. We prove how both MPA and EDT provide much more stability to PbS QD films to operate very efficiently up to 8 cycles of photocatalysis. As observed in XPS, the oxidation of PbS is prevented after ligand exchange. We demonstrate how surface chemistry engineering of solution-processed QD films can open a new approach towards the design of highly efficient and stable visible-light-driven photocatalysts, which paves the way to low cost and large area fabrication of high-performance photocatalytic devices.

Charge Transport in Trap-Sensitized Infrared PbS Quantum-Dot-Based Photoconductors: Pros and Cons.

Control of quantum-dot (QD) surface chemistry offers a direct approach for the tuning of charge-carrier dynamics in photoconductors based on strongly coupled QD solids. We investigate the effects of altering the surface chemistry of PbS QDs in such QD solids via ligand exchange using 3-mercaptopropionic acid (MPA) and tetrabutylammonium iodide (TBAI). The roll-to-roll compatible doctor-blade technique was used for the fabrication of the QD solid films as the photoactive component in photoconductors and field-effect phototransistors. The ligand exchange of the QD solid film with MPA yields superior device performance with higher photosensitivity and detectivity, which is due to less dark current and lower noise level as compared to ligand exchange with TBAI. In both cases, the mechanism responsible for photoconductivity is related to trap sensitization of the QD solid, in which traps are responsible of high photoconductive gain values, but slow response times under very low incident optical power (<1 pW). At medium⁻high incident optical powers (>100 pW), where traps are filled, both MPA- and TBAI-treated photodevices exhibit similar behavior, characterized by lower responsivity and faster response time, as limited by the mobility in the QD solid.

Optical Optimization of the TiO2 Mesoporous Layer in Perovskite Solar Cells by the Addition of SiO2 Nanoparticles.

In this work, SiO2 nanoparticles (NPs) were integrated into the mesoporous TiO2 layer of a perovskite solar cell to investigate their effect on cell performance. Different concentrations of SiO2/ethanol have been combined in TiO2/ethanol to prepare pastes for the fabrication of the mesoporous layer with which perovskite solar cells have been fabricated. Addition of SiO2 NPs of 50 and 100 nm sizes produces an enhancement of cell performance mainly because of an improvement of the photocurrent. This increment is in good agreement with the theoretical predictions based on light scattering induced by dielectric SiO2 NPs. The samples using modified scaffolds with NPs also present a significant lower current-potential hysteresis indicating that NP incorporation also affects the ion accumulation at the perovskite interface, providing an additional beneficial effect. The results stress the importance of the appropriated management of the optical properties on further optimization of perovskite solar cell technology.

Nanotexturing To Enhance Photoluminescent Response of Atomically Thin Indium Selenide with Highly Tunable Band Gap.

Manipulating properties of matter at the nanoscale is the essence of nanotechnology, which has enabled the realization of quantum dots, nanotubes, metamaterials, and two-dimensional materials with tailored electronic and optical properties. Two-dimensional semiconductors have revealed promising perspectives in nanotechnology. However, the tunability of their physical properties is challenging for semiconductors studied until now. Here we show the ability of morphological manipulation strategies, such as nanotexturing or, at the limit, important surface roughness, to enhance light absorption and the luminescent response of atomically thin indium selenide nanosheets. Besides, quantum-size confinement effects make this two-dimensional semiconductor to exhibit one of the largest band gap tunability ranges observed in a two-dimensional semiconductor: from infrared, in bulk material, to visible wavelengths, at the single layer. These results are relevant for the design of new optoelectronic devices, including heterostructures of two-dimensional materials with optimized band gap functionalities and in-plane heterojunctions with minimal junction defect density.

High spatial resolution mapping of individual and collective localized surface plasmon resonance modes of silver nanoparticle aggregates: correlation to optical measurements.

Non-isolated nanoparticles show a plasmonic response that is governed by the localized surface plasmon resonance (LSPR) collective modes created by the nanoparticle aggregates. The individual and collective LSPR modes of silver nanoparticle aggregated by covalent binding by means of bifunctional molecular linkers are described in this study. Individual contributions to the collective modes are investigated at nanometer scale by means of energy-filtering transmission electron microscopy and compared to ultraviolet-visible spectroscopy. It is found that the aspect ratio and the shape of the clusters are the two main contributors to the low-energy collective modes.

MWP phase shifters integrated in PbS-SU8 waveguides.

We present new kind of microwave phase shifters (MPS) based on dispersion of PbS colloidal quantum dots (QDs) in commercially available photoresist SU8 after a ligand exchange process. Ridge PbS-SU8 waveguides are implemented by integration of the nanocomposite in a silicon platform. When these waveguides are pumped at wavelengths below the band-gap of the PbS QDs, a phase shift in an optically conveyed (at 1550 nm) microwave signal is produced. The strong light confinement produced in the ridge waveguides allows an improvement of the phase shift as compared to the case of planar structures. Moreover, a novel ridge bilayer waveguide composed by a PbS-SU8 nanocomposite and a SU8 passive layer is proposed to decrease the propagation losses of the pump beam and in consequence to improve the microwave phase shift up to 36.5° at 25 GHz. Experimental results are reproduced by a theoretical model based on the slow light effect produced in a semiconductor waveguide due to the coherent population oscillations. The resulting device shows potential benefits respect to the current MPS technologies since it allows a fast tunability of the phase shift and a high level of integration due to its small size.

The effect of quantum size confinement on the optical properties of PbSe nanocrystals under exposure to heat and hydrostatic pressure.

A study based on photoluminescence and absorption measurements as a function of temperature and pressure for PbSe nanocrystals with sizes in the range 3-13 nm reveals the influence of size quantum confinement on the observed variation. In the case of the temperature variation, the effective bandgap changes from showing a positive rate of change to showing a negative one (for a quantum dot 3 nm in diameter), which can be accounted for by incorporating a linear variation of the carrier effective masses into a simple calculation of the exciton ground state in the quantum dot. In the case of the pressure variation, we observe a clear inverse correlation between the absolute value of the pressure coefficient and the nanocrystal size, a signature of quantum size confinement, with values changing from -76 to -41 meV GPa⁻¹ for quantum dots ranging from 13 to 3 nm in diameter, respectively, clearly smaller in absolute value than the rate for bulk PbSe (-84 meV GPa⁻¹). We used again the hypothesis of a linear variation of the carrier effective masses with pressure in order to fit this experimental variation quantitatively.

Laser-ablation-induced synthesis of SiO2-capped noble metal nanoparticles in a single step.

Here we describe a simple, powerful technique based on the laser ablation of a target immersed in a water solution of a metal salt. With this method, nanoparticles of different metals and alloys can be processed very quickly. Both the target and the salt solution can be chosen to produce metal nanoparticles of different sizes, surface-oxidized nanoparticles (silica-silver, for example), or even more complex structures to be defined by the researcher on one or more steps because the technique combines the advantages of both physical and chemical methods. We have applied this technique to the fabrication of inert silica-metal (silver, gold, and silver-gold) nanoparticles with a strong surface plasmon resonance all together in a single step. The advantage of the simultaneous production of silica during laser ablation is the stabilization of the metal nanoparticle colloid but also the possibility to reduce the toxicity of these nanoparticles.

Au-PVA nanocomposite negative resist for one-step three-dimensional e-beam lithography.

Au nanoparticles are synthesized in situ upon the electron beam exposure of a poly(vinyl alcohol) (PVA) thin film containing Au(III). The e-beam-irradiated areas are insoluble in water (negative-tone resist), and Au-PVA nanocomposite patterns with a variable profile along the structure can be thus generated (3D lithography) in a single step. A local characterization of the generated patterns is performed by high-resolution transmission electron microscopy and UV-vis localized surface plasmon resonance microspectroscopy. This characterization confirms the presence of crystalline nanoparticles and aggregates.