Enhanced Adsorption of Textile Dyes by a Novel Sulfonated Activated Carbon Derived from Pomegranate Peel Waste: Isotherm, Kinetic and Thermodynamic Study.

The rapid growth of the dye and textile industry has raised significant public concerns regarding the pollution caused by dye wastewater, which poses potential risks to human health. In this study, we successfully improved the adsorption efficiency of activated carbon derived from pomegranate peel waste (PPAC) through a single-step and surface modification approach using 5-sulfonate-salicylaldehyde sodium salt. This innovative and effective sulfonation approach to produce sulfonated activated carbon (S-PPAC) proved to be highly effective in removing crystal violet dye (CV) from polluted water. The prepared PPAC and S-PPAC were characterized via FESEM, EDS, FTIR and BET surface area. Characterization studies confirmed the highly porous structure of the PPAC and its successful surface modification, with surface areas reaching 1180.63 m2/g and 740.75 m2/g for the PPAC and S-PPAC, respectively. The maximum adsorption capacity was achieved at 785.53 mg/g with the S-PPAC, an increase of 22.76% compared to the PPAC at 45 °C. The isothermic adsorption and kinetic studies demonstrated that the adsorption process aligned well with the Freundlich isotherm model and followed the Elovich kinetic model, respectively. The thermodynamic study confirmed that the adsorption of CV dye was endothermic, spontaneous and thermodynamically favorable onto PPAC and S-PPAC.

Activated Carbon-Incorporated Tragacanth Gum Hydrogel Biocomposite: A Promising Adsorbent for Crystal Violet Dye Removal from Aqueous Solutions.

Biomaterials-based adsorbents have emerged as a sustainable and promising solution for water purification, owing to their eco-friendly nature and remarkable adsorption capacities. In this study, a biocomposite hydrogel was prepared by the incorporation of activated carbon derived from pomegranate peels (PPAC) in tragacanth gum (TG). The hydrogel biocomposite (PPAC/TG) showed a porous structure, a negative surface charge at a pH of more than 4.9, and good stability in aqueous media. The adsorption properties of the PPAC/TG hydrogel biocomposite were assessed for the removal of crystal violet dye (CV) from aqueous solutions using a batch adsorption. The equilibrium adsorption data followed the Sips isotherm model, as supported by the calculated R2 (>0.99), r-χ2 (<64), and standard error values (<16). According to the Sips model, the maximum values of the adsorption capacity of PPAC/TG were 455.61, 470.86, and 477.37 mg/g at temperatures of 25, 30, and 35 °C, respectively. The adsorption kinetic of CV onto the PPAC/TG hydrogel biocomposite was well described by the pseudo-second-order model with R2 values more than 0.999 and r-χ2 values less than 12. Thermodynamic studies confirmed that the CV dye adsorption was spontaneous and endothermic. Furthermore, the prepared hydrogel exhibited excellent reusability, retaining its adsorption capacity even after being used more than five times. Overall, this study concludes that the prepared PPAC/TG exhibited a significant adsorption capacity for cationic dyes, indicating its potential as an effective and eco-friendly adsorbent for water treatment.

Investigation of the Mechanical and Tribological Behavior of Epoxy-Based Hybrid Composite.

The main target of this study is to evaluate the impact of hybrid reinforcement using Al2O3 nanoparticles and graphite on the epoxy nanocomposites' mechanical and tribological properties. Various weight fractions of the reinforcement materials, ranging from 0 to 0.5 wt.%, were incorporated into the epoxy. The aim is to enhance the characteristics and durability of the polymers for potential utilization in different mechanical applications. The addition of hybrid additives consisting of Al2O3 nanoparticles and graphite to the epoxy resin had a noticeable effect on the performance of the epoxy nanocomposites. The incorporation of these additives resulted in increased elasticity, strength, toughness, ductility, and hardness as the concentration of reinforcement increased. The enhancement in the stiffness, mechanical strength, toughness and ductility reached 33.9%, 25.97%, 25.3% and 16.7%, respectively. Furthermore, the frictional tests demonstrated a notable decrease in both the coefficient of friction and wear with the rise of the additives' weight fraction. This improvement in the structural integrity of the epoxy nanocomposites led to enhanced mechanical properties and wear resistance. The SEM was utilized to assess the surfaces of tested samples and provide insights into the wear mechanism.

Investigating the Mechanical Properties of Annealed 3D-Printed PLA-Date Pits Composite.

Biomedical applications are crucial in rehabilitation medicine, assisting individuals with disabilities. Nevertheless, materials failure can sometimes result in inconvenience for users. Polylactic Acid (PLA) is a popular 3D-printed material that offers design flexibility. However, it is limited in use because its mechanical properties are inadequate. Thus, this study introduces an artificial intelligence model that utilizes ANFIS to estimate the mechanical properties of PLA composites. The model was developed based on an actual data set collected from experiments. The experimental results were obtained by preparing samples of PLA green composites with different weight fractions of date pits, which were then annealed for varying durations to remove residual stresses resulting from 3D printing. The mechanical characteristics of the produced PLA composite specimens were measured experimentally, while the ANSYS model was established to identify the composites' load-carrying capacity. The results showed that ANFIS models are exceptionally robust and compatible and possess good predictive capabilities for estimating the hardness, strength, and Young's modulus of the 3D-printed PLA composites. The model results and experimental outcomes were nearly identical.

Adaptive Neuro-Fuzzy-Based Models for Predicting the Tribological Properties of 3D-Printed PLA Green Composites Used for Biomedical Applications.

Tribological performance is a critical aspect of materials used in biomedical applications, as it can directly impact the comfort and functionality of devices for individuals with disabilities. Polylactic Acid (PLA) is a widely used 3D-printed material in this field, but its mechanical and tribological properties can be limiting. This study focuses on the development of an artificial intelligence model using ANFIS to predict the wear volume of PLA composites under various conditions. The model was built on data gathered from tribological experiments involving PLA green composites with different weight fractions of date particles. These samples were annealed for different durations to eliminate residual stresses from 3D printing and then subjected to tribological tests under varying normal loads and sliding distances. Mechanical properties and finite element models were also analyzed to better understand the tribological results and evaluate the load-carrying capacity of the PLA composites. The ANFIS model demonstrated excellent compatibility and robustness in predicting wear volume, with an average percentage error of less than 0.01% compared to experimental results. This study highlights the potential of heat-treated PLA green composites for improved tribological performance in biomedical applications.

Synergistic Effect of Nanoparticles: Enhanced Mechanical and Corrosion Protection Properties of Epoxy Coatings Incorporated with SiO2 and ZrO2.

This research paper presents the fabrication of epoxy coatings along with the hybrid combination of SiO2 and ZrO2. The epoxy resin is incorporated with SiO2 as the primary pigment and ZrO2 as the synergist pigment. The study delves into the adhesion, barrier, and anti-corrosion properties of these coatings, enriched with silica and zirconium nanoparticles, and investigates their impact on the final properties of the epoxy coating. The epoxy resin, a Diglycidyl ether bisphenol-A (DGEBA) type, is cured with a polyamidoamine adduct-based curing agent. To evaluate the protective performance of silica SiO2 and zirconia ZrO2 nanoparticles in epoxy coatings, the coated samples were tested in a 3.5% NaCl solution. The experimental results clearly demonstrate a remarkable improvement in the ultimate tensile strength (UTS), yield strength (YS), and Elastic Modulus. In comparison to using SiO2 separately, the incorporation of both ZrO2 and SiO2 resulted in a substantial increase of 43.5% in UTS, 74.2% in YS, and 8.2% in Elastic Modulus. The corrosion test results revealed that the combination of DGEBA, SiO2, and ZrO2 significantly enhanced the anti-corrosion efficiency of the organic coatings. Both these pigments exhibited superior anti-corrosion effects and mechanical properties compared to conventional epoxy coatings, leading to a substantial increase in the anti-corrosion efficiency of the developed coating. This research focuses the potential of SiO2 and ZrO2 in hybrid combination for applications, where mechanical, corrosion and higher adhesion to the substrates are of prime importance.

Unveiling the Potential of Rice Straw Nanofiber-Reinforced HDPE for Biomedical Applications: Investigating Mechanical and Tribological Characteristics.

The efficient utilization of rice waste has the potential to significantly contribute to environmental sustainability by minimizing the waste impact on the environment. Through repurposing such waste, novel materials can be developed for various biomedical applications. This approach not only mitigates waste, but it also promotes the adoption of sustainable materials within the industry. In this research, rice-straw-derived nanofibers (RSNFs) were utilized as a reinforcement material for high-density polyethylene (HDPE). The rice-straw-derived nanofibers were incorporated at different concentrations (1, 2, 3, and 4 wt.%) into the HDPE. The composites were fabricated using twin-screw extrusion (to ensure homogenous distribution) and the injection-molding process (to crease the test samples). Then, the mechanical strengths and frictional performances of the bio-composites were assessed. Different characterization techniques were utilized to investigate the morphology of the RSNFs. Thermal analyses (TGA/DTG/DSC), the contact angle, and XRD were utilized to study the performances of the HDPE/RSNF composites. The study findings demonstrated that the addition of RSNFs as a reinforcement to the HDPE improved the hydrophilicity, strength, hardness, and wear resistance of the proposed bio-composites.

The Effect of Zirconia Nanoparticles on Thermal, Mechanical, and Corrosion Behavior of Nanocomposite Epoxy Coatings on Steel Substrates.

Zirconia (ZrO2) nanoparticles (1-3 wt.%) were incorporated into the epoxy matrix using the ultra-sonication mixing method of dispersion to manufacture nanocomposite coatings. An automatic applicator was used to prepare the coating samples on a stainless steel substrate. The influence of ZrO2 nanoparticles on the physicochemical characteristics of epoxy coatings was evaluated using energy dispersive X-ray spectroscopy (EDS), field emission scanning electron microscopy (FE-SEM), Fourier-transform infrared spectroscopy (FTIR), thermos-gravimetric analysis (TGA), elastic modulus, and micro-hardness measurement with the nano-indentation technique. The corrosion stability during immersion in 3.5% NaCl solution was monitored using electrochemical impedance spectroscopy (EIS). All ZrO2-containing coatings showed better corrosion stability and adhesion than pure epoxy coating. Epoxy coating incorporated with 2% ZrO2 exhibited the greatest values of corrosion resistance and adhesion due to the effect of nanoparticle properties and their better de-agglomeration in the epoxy matrix than pure epoxy coating.

Investigation on mechanical properties and corrosion resistance of Ti-modified AA5083 aluminum alloy for aerospace and automotive applications.

Casting of aluminum with different concentration of alloying elements such as Mg, Mn (similar to that in AA5083) with additional percentages of 0.1, 0.2 and 0.3% Ti, are carried out using graphite crucible. The as-cast microstructure is modified by hot rolling to a thickness of ~ 2 mm. Mechanical and metallurgical and characterization of heat-treated thin sheets are carried out using tensile testing, hardness measurement, metallography, image analysis and optical microscope. By increasing the Ti content, the results show grain refinement and increase in the formation of Al3Ti which reflected positively on the mechanical properties. Specifically, Ultimate tensile strength is increased from 260 MPa (0 wt% Ti) to 345 MPa (0.3 wt% Ti) when using water quenching, 32.6% improvement for air cooling, and 23.3% for furnace cooling. Electrochemical corrosion behavior of heat-treated water quenched, air cooled and furnace cooled samples were tested in 3.5% NaCl solution. The results show that the heat-treated alloys have very good resistance against corrosion, while by increasing the Ti content, the corrosion rate increases due to the grain refinement phenomena.

Developing PMMA/Coffee Husk Green Composites to Meet the Individual Requirements of People with Disabilities: Hip Spacer Case Study.

When replacing a damaged artificial hip joint, treatment involves using antibiotic-laced bone cement as a spacer. One of the most popular materials used for spacers is PMMA; however, it has limitations in terms of mechanical and tribological properties. To overcome such limitations, the current paper proposes utilizing a natural filler, coffee husk, as a reinforcement for PMMA. The coffee husk filler was first prepared using the ball-milling technique. PMMA composites with varying weight fractions of coffee husk (0, 2, 4, 6, and 8 wt.%) were prepared. The hardness was measured to estimate the mechanical properties of the produced composites, and the compression test was utilized to estimate the Young modulus and compressive yield strength. Furthermore, the tribological properties of the composites were evaluated by measuring the friction coefficient and wear by rubbing the composite samples against stainless steel and cow bone counterparts under different normal loads. The wear mechanisms were identified via scanning electron microscopy. Finally, a finite element model for the hip joint was built to investigate the load-carrying capacity of the composites under human loading conditions. The results show that incorporating coffee husk particles can enhance both the mechanical and tribological properties of the PMMA composites. The finite element results are consistent with the experimental findings, indicating the potential of the coffee husk as a promising filler material for enhancing the performance of PMMA-based biomaterials.

Effect of Synthesized Titanium Dioxide Nanofibers Weight Fraction on the Tribological Characteristics of Magnesium Nanocomposites Used in Biomedical Applications.

Biomedical applications, such as artificial implants, are very significant for the disabled due to their usage in orthopedics. Nevertheless, available materials in such applications have insufficient mechanical and tribological properties. The current study investigated the mechanical and tribological properties of a biomedical metallic material, magnesium (Mg), after incorporating titanium dioxide nanofibers (TiO2) with different loading fractions. The TiO2 nanofibers were synthesized using the electrospinning technique. The ball-milling technique was utilized to ensure the homogenous distribution of TiO2 nanofibers inside the Mg matrix. Then, samples of the mixed powder with different loading fractions of TiO2 nanofibers, 0, 1, 3, 5, and 10 wt.%, were fabricated using a high-frequency induction heat sintering technique. The physicomechanical and tribological properties of the produced Mg/TiO2 nanocomposites were evaluated experimentally. Results showed an enhancement in mechanical properties and wear resistance accompanied by an increase in the weight fraction of TiO2 nanofibers up to 5%. A finite element model was built to assess the load-carrying capacity of the Mg/TiO2 composite to estimate different contact stresses during the frictional process. The finite element results showed an agreement with the experimental results.

Evaluating the Mechanical and Tribological Properties of 3D Printed Polylactic-Acid (PLA) Green-Composite for Artificial Implant: Hip Joint Case Study.

Artificial implants are very essential for the disabled as they are utilized for bone and joint function in orthopedics. However, materials used in such implants suffer from restricted mechanical and tribological properties besides the difficulty of using such materials with complex structures. The current study works on developing a new polymer green composite that can be used for artificial implants and allow design flexibility through its usage with 3D printing technology. Therefore, a natural filler extracted from corn cob (CC) was prepared, mixed homogeneously with the Polylactic-acid (PLA), and passed through a complete process to produce a green composite filament suit 3D printer. The corn cob particles were incorporated with PLA with different weight fractions zero, 5%, 10%, 15%, and 20%. The physical, mechanical, and tribological properties of the PLA-CC composites were evaluated. 3D finite element models were constructed to evaluate the PLA-CC composites performance on a real condition implant, hip joints, and through the frictional process. Incorporating corn cob inside PLA revealed an enhancement in the hardness (10%), stiffness (6%), compression ultimate strength (12%), and wear resistance (150%) of the proposed PLA-CC composite. The finite element results of both models proved an enhancement in the load-carrying capacity of the composite. The finite element results came in line with the experimental results.

Evaluating the Performance of 3D-Printed PLA Reinforced with Date Pit Particles for Its Suitability as an Acetabular Liner in Artificial Hip Joints.

Off-the-shelf hip joints are considered essential parts in rehabilitation medicine that can help the disabled. However, the failure of the materials used in such joints can cause individual discomfort. In support of the various motor conditions of the influenced individuals, the aim of the current research is to develop a new composite that can be used as an acetabular liner inside the hip joint. Polylactic acid (PLA) can provide the advantage of design flexibility owing to its well-known applicability as a 3D printed material. However, using PLA as an acetabular liner is subject to limitations concerning mechanical properties. We developed a complete production process of a natural filler, i.e., date pits. Then, the PLA and date pit particles were extruded for homogenous mixing, producing a composite filament that can be used in 3D printing. Date pit particles with loading fractions of 0, 2, 4, 6, 8, and 10 wt.% are dispersed in the PLA. The thermal, physical, and mechanical properties of the PLA-date pit composites were estimated experimentally. The incorporation of date pit particles into PLA enhanced the compressive strength and stiffness but resulted in a reduction in the elongation and toughness. A finite element model (FEM) for hip joints was constructed, and the contact stresses on the surface of the acetabular liner were evaluated. The FEM results showed an enhancement in the composite load carrying capacity, in agreement with the experimental results.

Mechanical, Microstructure, and Corrosion Characterization of Dissimilar Austenitic 316L and Duplex 2205 Stainless-Steel ATIG Welded Joints.

The present work analyzed the microstructure, mechanical, and corrosion properties of a dissimilar activated tungsten inert gas (ATIG) welded 2205 duplex stainless-steel (2205 DSS) plate and AISI 316L austenitic stainless steel (316L ASS) and compared them to conventional dissimilar welded tungsten inert gas (TIG). The mixing design method is a tool used to establish the optimal combined flux to achieve a full-penetrated weld bead in one single pass. A microstructure study was carried out by scanning electron microscopy (SEM). The ATIG and TIG fusion zones revealed a matrix ferrite structure with intragranular austenite, Widmanstätten needles, allotriomorphic austenite at the grain boundaries, and plate-like precipitates free of deleterious phases such as sigma and chi phases or second austinite owing to the moderate heat input provided of 0.8 kJ/mm. Ferrite volume proportion measurements were carried out utilizing the areas image processing software. The average ferrite volume proportion attained 54% in the ATIG weld zone; however, it decreased to 47% for the TIG weld zone. The results showed that the optimal flux composed by 91% Mn2O3 and 9% Cr2O3 allowed a full penetrated weld to be obtained in one single pass. However, a double side weld is required for conventional TIG processes. The values of the tensile (599 Mpa), hardness (235 HV), and impact test (267 J/cm2) measurements of ATIG welds were close to those of conventional TIG welds. The elaborated flux did not degrade the mechanical properties of the joint; on the contrary, it reinforced the strength property. The width of the ATIG heat-affected zone was narrower than that of TIG welding by 2.6 times, ensuring fewer joint distortions. The potentiodynamic polarization test results showed a better electrochemical behavior for ASS 316L than with the weldment and the parent metal of DSS 2205.

Electrochemical Behavior of Inductively Sintered Al/TiO2 Nanocomposites Reinforced by Electrospun Ceramic Nanofibers.

This study is focuses on the investigation of the effect of using TiO2 short nanofibers as a reinforcement of an Al matrix on the corrosion characteristics of the produced nanocomposites. The TiO2 ceramic nanofibers used were synthesized via electrospinning by sol-gel process, then calcinated at a high temperature to evaporate the residual polymers. The fabricated nanocomposites contain 0, 1, 3 and 5 wt.% of synthesized ceramic nanofibers (TiO2). Powder mixtures were mixed for 1 h via high-energy ball milling in a vacuum atmosphere before being inductively sintered through a high-frequency induction furnace at 560 °C for 6 min. The microstructure of the fabricated samples was studied by optical microscope and field emission scanning electron microscope (FESEM) before and after corrosion studies. Corrosion behavior of the sintered samples was evaluated by both electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization techniques (PPT) in 3.5% NaCl solution for one hour and 24-h immersion times. The results show that even though the percentage of ceramic nanofibers added negatively control corrosion resistance, it is still possible to increase resistance against corrosion for the fabricated nanocomposite by more than 75% in the longer exposure time periods.

Evaluation of Mechanical and Tribological Properties of Corn Cob-Reinforced Epoxy-Based Composites-Theoretical and Experimental Study.

Epoxy is considered to be the most popular polymer and is widely used in various engineering applications. However, environmental considerations require natural materials-based epoxy. This necessity results in further utilization of natural materials as a natural reinforcement for different types of composites. Corn cob is an example of a natural material that can be considered as an agricultural waste. The objective of the present work is to improve the economic feasibility of corn cob by converting the original corn cob material into powder to be utilized in reinforcing epoxy-based composites. In the experiment, the corn cob was crushed and ground using a grain miller before it was characterized by scanning electron microscopy (SEM). The corn cob powder was added to the epoxy with different weight fractions (2, 4, 6, 8, 10 wt%). In order to prevent corn cob powder agglomeration and ensure homogeneous distribution of the reinforcement inside the epoxy, the ultrasonic technique and a mechanical stirrer were used. Then, the composite's chemical compositions were evaluated using X-ray diffraction (XRD). The mechanical experiments showed an improvement in the Young's modulus and compressive yield strength of the epoxy composites, increasing corn cob up to 8 wt% by 21.26% and 22.22%, respectively. Furthermore, tribological tests revealed that reinforcing epoxy with 8 wt% corn cob can decrease the coefficient of friction by 35% and increase wear resistance by 4.8%. A finite element model for the frictional process was constructed to identify different contact stresses and evaluate the load-carrying capacity of the epoxy composites. The finite element model showed agreement with the experimental results. An epoxy containing 8 wt% corn cob demonstrated the optimal mechanical and tribological properties. The rubbed surfaces were investigated by SEM to identify the wear mechanism of different composites.

Mechanical Properties and Microstructural Characterization of Laser Welded S32520 Duplex Stainless Steel.

This paper investigates an experimental design of laser butt welding of S32520 duplex stainless steel, which has been passed out with the help of a pulsed Nd: YAG laser supply. The intention of the present research is to learn the impact of beam diameter, welding speed, and laser power on the superiority of the butt weld. The individuality of butt joints has been characterized in terms of tensile properties, fractography, and hardness. It was noticed that unbalanced particle orientations indirectly produce a comparatively fragile quality in the laser welded joint. The outcome of varying process parameters and interaction effect of process parameters on ultimate tensile strength and micro hardness were studied through analysis of experimental data. With different process parameters, the heat energy delivered to the material was changed, which was reflected in tensile strength measurement for different welded samples. From this present research, it was shown that, up to a certain level, an increase in process parameters amplified the tensile strength, but after that, certain level tensile strength decreased with the increase in process parameters. When process parameters exceeded that certain level, the required amount of heat energy was not delivered to the material, resulting in low bead width and less penetration, thus producing less strength in the welded joint. Less strength leads to more ductile weld joints. Microhardness was higher in the weld zone than in the base region of welded samples. However, the heat affected zone had a high microhardness range.

Effect of Graphene Concentration on the Electrochemical Properties of Cobalt Ferrite Nanocomposite Materials.

A two-step process was applied to synthesize the cobalt ferrite-graphene composite materials in a one-pot hydrothermal reaction process. Graphene Oxide (GO) was synthesized by a modified Hummer's method. The synthesized composite materials were characterized by X-ray diffraction (XRD), thermogravimetric analysis (TGA), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), and Fourier-transform infrared spectroscopy (FTIR). The XRD and FTIR results were in good agreement with the TGA/DTG observations. SEM and TEM disclosed the spherical shape of the nanoparticles in 4-10 nm. The optimized CoFe2O4-G (1-5 wt.%) composite materials samples were tried for their conductivity, supercapacity, and corrosion properties. The CV results demonstrated a distinctive behavior of the supercapacitor, while the modified CoFe2O4-G (5 wt.%) electrode demonstrated a strong reduction in the Rct value (~94 Ω). The highest corrosion current density valves and corrosion rates were attained in the CoFe2O4-G (5 wt.%) composite materials as 5.53 and 0.20, respectively. The high conductivity of graphene that initiated the poor corrosion rate of the CoFe2O4-graphene composite materials could be accredited to the high conductivity and reactivity.

Alloying Elements Effects on Electrical Conductivity and Mechanical Properties of Newly Fabricated Al Based Alloys Produced by Conventional Casting Process.

The present investigation deals with a comprehensive study on the production of aluminum based alloys with the incorporation of different alloying elements and their effect on its electrical conductivity and mechanical properties. Casting of pure aluminum with different concentration and combinations of alloying additives such as cupper (Cu), magnesium (Mg) and silver (Ag) were carried out using a graphite crucible. The as-cast microstructure was modified by hot rolling followed by different heat-treated conditions viz., annealing, normalizing, quenching, and age hardening. The mechanical properties and electrical conductivity of the produced heat-treated alloys sheets under various processing conditions were carried out using tensile testing, hardness, and electrical resistivity measurements. It was found that by increasing the alloying elements content, yield strength results increased significantly by more than 250% and 500% for the as rolled and 8 h aged Al-Cu-Mg alloy, respectively. On the other hand, the electrical conductivity reduces slightly with -14.6% and -16.57% for the as rolled and 8 h aged of the same Al-Cu-Mg alloy, respectively.

Ethanedihydrazide as a Corrosion Inhibitor for Iron in 3.5% NaCl Solutions.

Corrosion of iron in sodium chloride (3.5% wt) solutions and its inhibition by ethanedihydrazide (EH) have been reported. Electrochemical impedance spectroscopy (EIS), cyclic potentiodynamic polarization (CPP), and change of current with time at -475 mV (Ag/AgCl) measurements were employed in this study. Scanning electron microscopy (SEM) and energy-dispersive X-ray (EDX) techniques were utilized to report surface morphology and elemental analysis, respectively. The presence of 5 × 10-5 M EH was found to inhibit the corrosion of iron, and the effect of inhibition profoundly increased with an increase in EH concentration up to 1 × 10-4 M and further to 5 × 10-4 M. The low values of corrosion current and high corrosion resistance, which were obtained from the EIS, CPP, and change of current with time experiments, affirmed the adequacy of EH as a corrosion inhibitor for iron. Surface investigations demonstrated that the chloride solution without EH molecules causes severe corrosion, while the coexistence of EH within the chloride solution greatly minimizes the acuteness of chloride, particularly pitting corrosion.