Stability of dental implants with sandblasted and acid-etched (SLA) and modified (SLActive) surfaces during the osseointegration period.

Background. The surface properties of implants are effective factors for increasing the osseointegration and activity of osteoprogenitor cells. This study compared the stability of dental implants with sandblasted and acid-etched (SLA) and modified surfaces (SLActive) using the resonance frequency analysis (RFA). Methods. In a split-mouth design, 50 dental implants with either SLA surface properties (n=25) or modified (SLActive) surface properties (n=25) were placed in the mandibles of 12 patients with a bilateral posterior edentulous area. Implant stability was measured using RFA (Osstell) at implant placement time and every week for 1, 2, and 3 months before the conventional loading time. Results. One week following the implantation, implant stability increased from 70 to 77.67 for SLA and from 71.67 to 79 for SLActive (P < 0.05). Stability improved each week except in the 4th week in SLActive surface measurements. No significant differences were observed between the groups at 2 and 3 months (P > 0.05). Conclusions. For both implant surfaces, increased stability was observed over time, with no significant differences between the groups.

A survey of antibiotic resistance in Streptococcus pneumoniae and Haemophilus influenzae in Turkey, 2004 2005.

OBJECTIVES: To determine the prevalence of antimicrobial resistance among Streptococcus pneumoniae and Haemophilus influenzae isolated in Turkey as part of Survey Of Antibiotic Resistance, a surveillance programme in the Africa and Middle East region examining the antimicrobial susceptibility of key bacterial pathogens involved in community-acquired respiratory tract infections (CARTIs). METHODS: Susceptibility was evaluated against a range of antimicrobial agents using disc diffusion and Etest methods. RESULTS: Six centres in five cities collected 301 S. pneumoniae and 379 H. influenzae isolates between October 2004 and November 2005. Among S. pneumoniae, the prevalence of isolates with intermediate susceptibility (MICs 0.12-1 mg/L) and resistance to penicillin (MICs >or=2 mg/L) was 24.6% and 7.6%, respectively; there was a wide variation between cities (2.4% to 36.9% intermediate and 0% to 23.8% resistant phenotypes). Macrolide-azalide resistance rates exceeded those of penicillin resistance in all cities. Overall, 5.0% of isolates were co-resistant to penicillin and erythromycin and 10.0% were multidrug-resistant (joint resistance to erythromycin, co-trimoxazole and tetracycline). Agents tested to which over 90% of countrywide S. pneumoniae isolates remained susceptible were amoxicillin/clavulanate (98.7%), chloramphenicol (94.7%) and cefprozil (90.6%). Overall, the percentage of H. influenzae isolates producing beta-lactamase was 5.5%, differing widely across the country with the highest prevalence of beta-lactamase production detected in Trabzon (14.0%) and no beta-lactamase-positive isolates found in Izmir. H. influenzae had the highest per cent susceptibility to amoxicillin/clavulanate (99.5%) and ofloxacin (99.2%) while >20% were resistant to co-trimoxazole. CONCLUSIONS: Prevalence of penicillin and macrolide-azalide resistance among S. pneumoniae appears to be on the increase in Turkey while overall beta-lactamase production in H. influenzae remains relatively low. To adequately monitor the spread of drug-resistant phenotypes among these two important CARTI pathogens, ongoing collection of resistance surveillance data is required-where possible locally as resistance patterns can vary substantially between cities and institutions.

Effects of airborne-particle abrasion, sodium hydroxide anodization, and electrical discharge machining on porcelain adherence to cast commercially pure titanium.

The aim of this study was to determine the effect of airborne-particle abrasion (APA), sodium hydroxide anodization (SHA), and electrical discharge machining (EDM) on cast titanium surfaces and titanium-porcelain adhesion. Ninety titanium specimens were cast with pure titanium and the alpha-case layer was removed. Specimens were randomly divided into three groups. Ten specimens from each group were subjected to APA. SHA was applied to the second subgroups, and the remaining specimens were subjected to the EDM. For the control group, 10 specimens were cast using NiCr alloy and subjected to only APA. Surfaces were examined by using scanning electron microscope and a surface profilometer. Three titanium porcelains were fused on the titanium surfaces, whereas NiCr specimens were covered with conventional porcelain. Titanium-porcelain adhesion was characterized by a 3-point bending test. Statistical analysis showed that the porcelain-metal bond strength of the control group was higher than that of the titanium-porcelain system (p < 0.05). There were no significant differences between the bond strengths of titanium groups (p 0.05), except the bond strengths of Noritake Super Porcelain TI-22 groups on which APA and SHA were applied (p < 0.05). SHA and EDM as surface treatment did not improve titanium-porcelain adhesion when compared to APA.

Effects of sandblasting and electrical discharge machining on porcelain adherence to cast and machined commercially pure titanium.

The aim of this study was to determine the effect of sandblasting and electrical discharge machining (EDM) on cast and machined titanium surfaces and titanium-porcelain adhesion. Twenty machined titanium specimens were prepared by manufacturer (groups 1 and 2). Thirty specimens were prepared with autopolymerizing acrylic resin. Twenty of these specimens (groups 3 and 4) were cast with commercially pure titanium and the alpha-case layer was removed. For control group (group 5), 10 specimens were cast by using NiCr alloy. Groups 2 and 4 were subjected to EDM while groups 1, 3, and 5 were subjected to sandblasting. Surface examinations were made by using a scanning electron microscope (SEM). A low-fusing porcelain was fused on the titanium surfaces, whereas NiCr specimens were covered using a conventional porcelain. Titanium-porcelain adhesion was characterized by a 3-point bending test. Results were analyzed by Kruskal-Wallis and Mann-Whitney U tests. Metal-porcelain interfaces were characterized by SEM. The bond strength of control group was higher than that of the titanium-porcelain system. There was no significant difference between cast and machined titanium groups (p > 0.05). There was no significant difference between EDM and sandblasting processes (p > 0.05). The use of EDM as surface treatment did not improve titanium-porcelain adhesion compared with sandblasting.

Use of the fertilized hen's egg in the evaluation of embryotoxicity of dental alloys.

In this study, embryotoxic effects of five commercially available dental alloys were investigated by using fertilized hens' eggs. One sample of each alloy was conditioned in one of the conditioning media, physiological saline (PS), 0.1 M phosphate-buffered saline (PBS, pH 7.4), and 0.1 M protein (3% bovine serum albumin, BSA) containing PBS (pH 6.8), respectively. The test solutions were injected into the fertilized hen's eggs via air sac at the beginning of the incubation. Various concentrations of a highly embryotoxic substance, AFB1, was also used as positive control test material. Mortality of the AFB1 treatment groups increased with increasing concentrations of AFB1 and the mortality values were significantly (p < 0.05) higher than those of the controls and eluent injected groups. The eluents of five commercially available dental alloys tested in the study did not have significant embryotoxic effects. Cu- and Pd-containing alloys displayed relatively high but statistically insignificant embryotoxic effects. Chick embryo might be used in determination of the embryotoxic effects of the dental alloys with its several advantages. Nevertheless, the test should be further standardized and new methods such as micronucleus test showing possible genotoxic effects of the materials should be used.