Advanced NH3 Detection by 1D Nanostructured La:ZnO Sensors with Novel Intrinsic p-n Shifting and Ultrahigh Baseline Stability.

Due to its stability, transportability, and ability to be produced using renewable energy sources, NH3 has become an attractive option for hydrogen production and storage. Detecting NH3 is then essential, being a toxic and flammable gas that can pose dangers if not properly monitored. ZnO chemiresistive sensors have shown great potential in real NH3 monitoring applications; yet, research and development in this area are ongoing due to reported limitations, like baseline instabilities and sensitivity to environmental factors, including temperature, humidity, and interferent gases. Herein, we suggest an approach to obtain sensors with competitive performance based on ZnO semiconducting metal oxides. For this purpose, one-dimensional nanostructured pure and La-doped ZnO films were synthesized hydrothermally. Incorporating large rare earth ions, like La, into the bulk lattice of ZnO is challenging and can lead to surface defects that are influential in gas-sensing reactions. The sensors experienced a temperature-induced p-n shifting at about 100 °C, verified by the Hall effect and AC impedance measurements. The doped sensor showed exceptional stepwise baseline stability and outstanding performance at a relatively low operating temperature (150 °C) with a sensing response of 91 at best (@ 50 ppm NH3) and recorded a tolerance to water vapor up to 70% RH. Alongside p-n shifting, the enhanced performance was discussed in correlation with La doping-triggered changes in the nanostructural and surfacial properties of the films. We validated the proposed technique by producing similar sensors and performing multiple replicates to ensure consistency and reproducibility. We also introduced the fill factor concept into the gas sensor field as a new trustworthy parameter that could improve sensor performance assessment and help rate sensors based on deviation from ideality.

Quick NO Gas Sensing by Ti-Doped Flower-Rod-like ZnO Structures Synthesized by the SILAR Method.

In this study, Ti-doped ZnO films with flower-rod-like nanostructures were synthesized by the successive ionic layer adsorption and reaction (SILAR) method for enhanced NO gas-sensing applications. The stoichiometric ratio of Ti in the host ZnO lattice was confirmed by atomic absorption and energy-dispersive X-ray spectroscopies. All of the synthesized films exhibited a pure wurtzite hexagonal structure that seemed to deteriorate at high Ti doping contents as was manifested by the measured X-ray diffraction patterns. Scanning electron microscopy images of ZnO revealed the coexistence of porous flower- and rod-like structures, which became finer, denser, and more compact with Ti doping. By UV-vis measurements, the transmittance of the synthesized pure ZnO thin film in the visible region (∼75%) increased by about 10% with Ti doping, and the energy band gap seemed to decrease up to some limit of Ti content. Among the fabricated sensors (based on pure ZnO, 1% Ti-doped, 3% Ti-doped, and 5% Ti-doped ZnO films), the best sensing performance was observed for the 1% Ti-doped ZnO film. At first, this was associated with its high density of oxygen vacancies present on the surface of the film and ionized oxygen vacancies present in the ZnO lattice (confirmed, respectively, by X-ray photoelectron and photoluminescence spectroscopies). Nonetheless, this may also be due to its increased crystallinity (confirmed by X-ray diffraction and photoluminescence spectroscopy), high area-to-volume ratio (confirmed by scanning electron microscopy images), high specific surface area (confirmed by Brunauer-Emmett-Teller measurements) as well as high mobility and carrier concentration (confirmed by Hall measurements). The sensor was highly selective to NO gas and showed notable stability as well as very short response and recovery times, which makes it eligible for the early detection of any indoor or outdoor NO gas leakages.

Effect of Ni and Al doping on structural, optical, and CO2 gas sensing properties of 1D ZnO nanorods produced by hydrothermal method.

In the present study, the one-dimensional ZnO nanorod structures are produced within the different nickel and aluminum molecular weight ratios of 0-7% using the hydrothermal method. It is found that the aluminum (Al) and nickel (Ni) impurities with different ionic radius, chemical valence, and electron configurations of outer shell cause to vary the fundamental characteristic features including the crystallinity quality, crystallite size, surface morphology, nanorod diameter, optical absorbance, energy band gap, resistance, gas response, and gas sensing properties. The structural analyses performed by powder X-ray diffraction (XRD) and scanning electron microscopy (SEM) indicate that the samples are found to crystallize in the hexagonal wurtzite structure. The presence of optimum nickel and aluminum in the crystal system improves considerably the crystallinity quality and surface morphology. Additionally, the combination of electron dispersive X-ray (EDX) and XRD results declare that the Ni and Al impurities incorporate successfully into the ZnO crystal structure. Moreover, the diameters of nanorod structures in 1D orientation are determined to be 80 nm or below. The hexagonal wurtzite-type ZnO nanorod structure prepared by 5% Ni has more space between the nanorods and thus presents higher response to the CO2 detection. Further, the optical absorbance spectra display that the band gap value is observed to decrease regularly with the increment in the doping level as a result of band shrinkage effect depending on the enhancement of mobile hole carrier concentrations in the crystal structure. In other words, the doping mechanism leads to vary the homogeneities in the interfacial charges, nanorod diameters, ZnO oxide layer composition and thickness. The last test conducted in this study is responsible for the determination of CO2 gas sensing levels. The obtained gas sensing results are further compared with each other and literature findings. It is observed that 5% Ni-doped sample provides more successful results than other samples in the sensing CO2 gas at the different concentrations. All in all, the paper establishing a strong methodology between doping mechanism and change in the fundamental characteristic features of hexagonal wurtzite-type ZnO with the aid of advanced microscopy techniques will become pioneering research to answer key questions in materials sciences and electronic research.

Fabrication and characterization of PVA/ODA-MMT-poly(MA-alt-1-octadecene)-g-graphene oxide e-spun nanofiber electrolytes and their response to bone cancer cells.

This work presents a new approach to fabrication and characterization of novel polymer nanofiber electrolytes from intercalated PVA/ODA-MMT nanocomposite as a matrix polymer and encapsulated graphene oxide (GO) nanosheets with amphiphilic reactive copolymer as partner polymers using electrospinning method. The chemical and physical structures, surface morphology, thermal behaviors and electric conductivity of nanocomposites and nanofibers were investigated using analyses methods including FTIR, XRD, SEM, DSC-TGA and conductivity analysis. Significant improvements in nanofiber morphology and size distribution were observed when GO and reactive organoclay were incorporated as reinforcement fillers into various matrix/partner solution blends. The structural factors of matrix-partner polymer nanocomposite particles with higher zeta-potential play important roles in both chemical and physical interfacial interactions and phase separation processing and also lead to the formation of nanofibers with unique surface morphologies and good conductivities. The cytotoxic, necrotic and apoptotic effects of chosen nanofibers on osteocarcinoma cells were also investigated. These multifunctional, self-assembled, nanofibrous surfaces can serve as semi-conductive and bioactive platforms in various electrochemical and bio-engineering processes, as well as reactive matrices used for the immobilization of various biopolymer precursors.

Novel multifunctional colloidal carbohydrate nanofiber electrolytes with excellent conductivity and responses to bone cancer cells.

This work presents a new approach to fabricating novel polymer nanofiber composites (NFCs) from water solution blends of PVA (hydrolyzed 89%)/ODA-MMT and Na-CMC/ODA-MMT nanocomposites as well as their folic acid (FA) incorporated modifications (NC-3-FA and NC-4-FA) through green electrospinning nanotechnology. The chemical and physical structures and surface morphology of the nanofiber composites were confirmed. Significant improvements in nanofiber morphology and size distribution of the NFC-3-FA and NFC-4-FA nanofibers with lower average means 110 and 113nm compared with those of NFC-1/NFC-2 nanofibers (270 and 323nm) were observed. The structural elements of polymer NFCs, particularly loaded partner NC-2, plays an important role in chemical and physical interfacial interactions, phase separation processing and enables the formation of nanofibers with unique morphology and excellent conductivity (NFC-3-FA 3.25×10(-9)S/cm and NFC-4-FA 8.33×10(-4)S/cm). This is attributed to the higher surface contact areas and multifunctional self-assembled supramacromolecular nanostructures of amorphous colloidal electrolytes. The anticancer activity of FA-containing nanofibers against osteocarcinoma cells were evaluated by cytotoxicity, apoptotic and necrotic analysis methods.