Signal replication in a DNA nanostructure.

Logic circuits based on DNA strand displacement reaction are the basic building blocks of future nanorobotic systems. The circuits tethered to DNA origami platforms present several advantages over solution-phase versions where couplings are always diffusion-limited. Here we consider a possible implementation of one of the basic operations needed in the design of these circuits, namely, signal replication. We show that with an appropriate preparation of the initial state, signal replication performs in a reproducible way. We also show the existence of side effects concomitant to the high effective concentrations in tethered circuits, such as slow leaky reactions and cross-activation.

Multi-MHz micro-electro-mechanical sensors for atomic force microscopy.

Silicon ring-shaped micro-electro-mechanical resonators have been fabricated and used as probes for dynamic atomic force microscopy (AFM) experiments. They offer resotnance frequency above 10MHz, which is notably greater than that of usual cantilevers and quartz-based AFM probes. On-chip electrical actuation and readout of the tip oscillation are obtained by means of built-in capacitive transducers. Displacement and force resolutions have been determined from noise analysis at 1.5fm/√Hz and 0.4 pN/√Hz, respectively. Despite the high effective stiffness of the probes, the tip-surface interaction force is kept below 1 nN by using vibration amplitude significantly below 100pm and setpoint close to the free vibration conditions. Imaging capabilities in amplitude- and frequency-modulation AFM modes have been demonstrated on block copolymer surfaces. Z-spectroscopy experiments revealed that the tip is vibrating in permanent contact with the viscoelastic material, with a pinned contact line. Results are compared to those obtained with commercial AFM cantilevers driven at large amplitudes (>10nm).

G-Quadruplexes Light up Localized DNA Circuits.

DNA circuits tethered to nanoplatforms can perform cascade reactions for signal amplification. One DNA single strand activates a strand-displacement cascade generating numerous outputs, and therefore amplifying the signal. These localized circuits present, however, an important limitation: the spontaneous activation of the cascade reaction. Current methods to stabilize these circuits employ combination of protective DNA strands, which need to be removed to activate the device. This protection-deprotection process generates an important amount of unwanted side reactions. This is indeed an important limitation for the large potential application of these amplification circuits. In the present work, G-quadruplex DNA structures were used to stabilize localized DNA circuits. This new protocol generates nanoplatforms that no longer requires protective-deprotective systems and is therefore completely neutral to the sample. In addition, cations such as Pb(2+) or Ca(2+) can be also employed to activate the device enlarging the potential applications from biosensors devices to metal detector sensors.

Shape and Effective Spring Constant of Liquid Interfaces Probed at the Nanometer Scale: Finite Size Effects.

We investigate the shape and mechanical properties of liquid interfaces down to nanometer scale by atomic force microscopy (AFM) and scanning electron microscopy (SEM) combined with in situ micromanipulation techniques. In both cases, the interface is probed with a cylindrical nanofiber with radius R of the order of 25-100 nm. The effective spring constant of the nanomeniscus oscillated around its equilibrium position is determined by static and frequency-modulation (FM) AFM modes. In the case of an unbounded meniscus, we find that the effective spring constant k is proportional to the surface tension γ of the liquid through k = (0.51 ± 0.06)γ, regardless of the excitation frequency from quasi-static up to 450 kHz. A model based on the equilibrium shape of the meniscus reproduces well the experimental data. Electron microscopy allowed to visualize the meniscus profile around the fiber with a lateral resolution of the order of 10 nm and confirmed its catenary shape. The influence of a lateral confinement of the interface is also investigated. We showed that the lateral extension L of the meniscus influences the effective spring constant following a logarithmic evolution k ∼ 2πγ/ln(L/R) deduced from the model. This comprehensive study of liquid interface properties over more than 4 orders of magnitude in meniscus size shows that advanced FM-AFM and SEM techniques are promising tools for the investigation of mechanical properties of liquids down to nanometer scale.

Connecting localized DNA strand displacement reactions.

Logic circuits based on DNA strand displacement reactions have been shown to be versatile enough to compute the square root of four-bit numbers. The implementation of these circuits as a set of bulk reactions faces difficulties which include leaky reactions and intrinsically slow, diffusion-limited reaction rates. In this paper, we consider simple examples of these circuits when they are attached to platforms (DNA origamis). As expected, constraining distances between DNA strands leads to faster reaction rates. However, it also induces side-effects that are not detectable in the solution-phase version of this circuitry. Appropriate design of the system, including protection and asymmetry between input and fuel strands, leads to a reproducible behaviour, at least one order of magnitude faster than the one observed under bulk conditions.

Guided assembly of tetramolecular G-quadruplexes.

Nucleic acids are finding applications in nanotechnology as nanomaterials, mechanical devices, templates, and biosensors. G-quadruplex DNA, formed by π-π stacking of guanine (G) quartets, is an attractive alternative to regular B-DNA because of the kinetic and thermodynamic stability of quadruplexes. However, they suffer from a fatal flaw: the rules of recognition, i.e., the formation of a G-quartet in which four identical bases are paired, prevent the controlled assembly between different strands, leading to complex mixtures. In this report, we present the solution to this recognition problem. The proposed design combines two DNA elements: parallel-stranded duplexes and a quadruplex core. Parallel-stranded duplexes direct controlled assembly of the quadruplex core, and their strands present convenient points of attachments for potential modifiers. The exceptional stability of the quadruplex core provides integrity to the entire structure, which could be used as a building block for nucleic acid-based nanomaterials. As a proof of principle for the design's versatility, we assembled quadruplex-based 1D structures and visualized them using atomic force and transmission electron microscopy. Our findings pave the way to broader utilization of G-quadruplex DNA in structural DNA nanomaterials.

Cooperativity in the annealing of DNA origamis.

DNA based nanostructures built on a long single stranded DNA scaffold, known as DNA origamis, offer the possibility to organize various molecules at the nanometer scale in one pot experiments. The folding of the scaffold is guaranteed by the presence of short, single stranded DNA sequences (staples), that hold together separate regions of the scaffold. In this paper, we modelize the annealing-melting properties of these DNA constructions. The model captures important features such as the hysteresis between melting and annealing, as well as the dependence upon the topology of the scaffold. We show that cooperativity between staples is critical to quantitatively explain the folding process of DNA origamis.

Modeling the mechanical properties of DNA nanostructures.

We discuss generalizations of a previously published coarse-grained description [Mergell et al., Phys. Rev. E 68, 021911 (2003)] of double stranded DNA (dsDNA). The model is defined at the base-pair level and includes the electrostatic repulsion between neighbor helices. We show that the model reproduces mechanical and elastic properties of several DNA nanostructures (DNA origamis). We also show that electrostatic interactions are necessary to reproduce atomic force microscopy measurements on planar DNA origamis.

Direct visualization of transient thermal response of a DNA origami.

The DNA origami approach enables the construction of complex objects from DNA strands. A fundamental understanding of the kinetics and thermodynamics of DNA origami assembly is extremely important for building large DNA structures with multifunctionality. Here both experimental and theoretical studies of DNA origami melting were carried out in order to reveal the reversible association/disassociation process. Furthermore, by careful control of the temperature cycling via in situ thermally controlled atomic force microscopy, the self-assembly process of a rectangular DNA origami tile was directly visualized, unveiling key mechanisms underlying their structural and thermodynamic features.

Folding of small origamis.

A model that preserves the known thermodynamic properties of double stranded DNA is introduced to study the formation of more complex DNA constructions, such as small origamis or Holliday junctions. We show that the thermodynamic behaviour of these complex DNA constructions is not only given by their sequence but also by their topology.

Investigation of the carbon nanotube AFM tip contacts: free sliding versus pinned contact.

Mechanical response of carbon nanotube atomic force microscope probes are investigated using a thermal noise forcing. Thermal noise spectra are able to investigate mechanical behaviors that cannot be studied using classical atomic force microscope modes. Experimental results show that the carbon nanotube contacts can be classified in two categories: the free sliding and pinned cases. The pinned contact case requires the description of the cantilever flexural vibrations with support spring-coupled cantilever boundary conditions. Our experimental results show that carbon nanotubes exhibit different contact behaviors with a surface, and in turn different mechanical responses.

Competition of elastic and adhesive properties of carbon nanotubes anchored to atomic force microscopy tips.

In this paper we address the mechanical properties of carbon nanotubes anchored to atomic force microscopy (AFM) tips in a detailed analysis of experimental results and exhaustive description of a simple model. We show that volume elastic and surface adhesive forces both contribute to the dynamical AFM experimental signals. Their respective weights depend on the nanotube properties and on an experimental parameter: the oscillation amplitude. To quantify the elastic and adhesive contributions, a simple analytical model is used. It enables analytical expressions of the resonance frequency shift and dissipation that can be measured in the atomic force microscopy dynamical frequency modulation mode. It includes the nanotube adhesive contribution to the frequency shift. Experimental data for single-wall and multi-wall carbon nanotubes compare well to the model predictions for different oscillation amplitudes. Three parameters can be extracted: the distance necessary to unstick the nanotube from the surface and two spring constants corresponding to tube compression and to the elastic force required to overcome the adhesion force.

Enzymatic activity of immobilized yeast phosphoglycerate kinase.

This work reports the first evidence that recombinant yeast phosphoglycerate kinase (PGK) is still significantly active when immobilized on glass and muscovite mica. Using previous work to improve the sensitivity of the existing setup, Tapping Mode atomic force microscopy (AFM) was used in a liquid environment to determine the surface enzyme coverage of derivatized mica and glass slides. When associated to spectrophotometric measurements, the AFM data allows assessing the catalytic constant of surface enzymes and comparing it to bulk values. The validity of the Michaelis-Menten model for surface reactions is discussed, supported by spectroscopic measurements of the surface consumption of 1,3-bis-phosphoglycerate (1,3-BPG). Only a few percent of the enzyme material maintains its initial bulk activity. This value could constitute a guideline for biosensors made with the method used here whenever a rapid assessment of the remaining surface activity is needed.

Oscillatory dissipation of a simple confined liquid.

We present a sensitive measurement of the dissipation and the effective viscosity of a simple confined liquid (octamethylcyclotetrasiloxane) using an atomic force microscope. The experimental data show that the damping and the effective viscosity increase and present oscillations as the gap between the cantilever tip and the surface is diminished. To our knowledge, the damping and the viscosity modulation are reported here with such good accuracy for the first time. Such an experimental result is different from what has been reported earlier where only a continuous increase of the damping and the viscosity are observed.

Liquid mechanical behavior of mixed monolayers of amino and alkyl silanes by atomic force microscopy.

The adsorption of mixed terminally aminated organosilyl compounds with long-chain n-alkyltrichlorosilanes on silica substrates has been studied by FTIR and AFM to deposit and study DNA. By optimization of deposition conditions, the mixed monolayers were found to be well organized and homogeneous. The amino group was protected to obtain a reproducible grafting and then deprotected after the film formation. In addition, atomic force microscopy (AFM) studies in both dynamical modes, amplitude modulation and frequency modulation, reveal that the layer behaves as a fluid as measured by the tip-cantilever and has a smaller characteristic time than the tip-cantilever. For three amplitudes, the experimental frequency shifts have been modeled for a fluidlike layer crossed by the tip. Finally, we show that this new fluidlike monolayer is suitable for DNA deposition and AFM studies.