Startup performance and microbial composition of a pilot-scale rapid sand filter for the treatment of manganese-containing mine water.

The inexpensive removal of soluble manganese [Mn(II)] from mine water that contains large quantities of Mn(II) should be prioritized given that large quantities of alkaline reagents are typically used in the chemical treatment of Mn-rich water from abandoned mines. Rapid sand filter (RSF) systems are widely used as a cost-effective technology in drinking water treatment processes to remove iron and Mn from groundwater. Here, we applied a pilot-scale RSF to treat mine water with a neutral pH and containing approximately 22 mg/L of Mn(II). Following a lag phase from its startup (day 1-day 26), Mn removal rates increased to approximately 40% for around 1 month (day 27-day 55) without the use of alkaline reagents but did not increase during further operation. Quantitative elemental analysis revealed Mn oxides on the sand filters during the Mn removal period. The bacterial communities on the RSFs, recorded on day 42 and day 85, were characterized and compared using 16S rRNA gene amplicon sequencing. Although the well-known Mn-oxidizing bacteria (MOB) were not listed among the ten most dominant operational taxonomic units (OTUs) on the sand filters (relative abundances: >0.68%), a significant increase in the OTUs related to well-known alphaproteobacterial MOB, such as Pedomicrobium spp., were observed during the period.

Nitrate-Driven Trophic Association of Sulfur-Cycling Microorganisms in Tsunami-Deposited Marine Sediment Revealed by High-Sensitivity 13C-Bicarbonate Probing.

Although denitrification-dependent chemolithotrophic sulfur oxidizers proliferated in tsunami-deposited marine sediment with nitrate amendment, their ecophysiological roles in biogeochemical carbon transfer are not addressed. We employed time-resolved high-sensitivity 13C-bicarbonate probing of rRNA to unveil the carbon fixation and resulting trophic relationship of the nitrate-amended sediment microorganisms. Nitrate reduction and sulfur oxidation co-occurred along with significant decreases in the 13CO2 and dissolved bicarbonate concentrations for the first 4 days of the incubation, during which the denitrification-dependent sulfur-oxidizing chemolithotrophs, i.e., the Sulfurimonas sp. HDS01 and Thioalkalispira sp. HDS22 relatives, and the sulfate-reducing heterotrophs, i.e., the Desulfobulbus spp. and Desulfofustis glycolicus relatives, actively incorporated 13C. These indicated that the sulfur oxidizers and sulfate reducers were tightly associated with each other through the direct carbon transfer. Relatives of the fermentative Thalassomonas sediminis and the hydrolytic Pararheinheimera aquatica, in addition to various sulfur-cycling microorganisms, significantly assimilated 13C at day 14. Although the incorporation of 13C was not detected, a syntrophic volatile-fatty-acid oxidizer and hydrogenotrophic methanogens significantly expressed their 16S rRNA molecules at day 21, indicating the metabolic activation of these final decomposers under the latter nutrient-limited conditions. The results demonstrated the nitrate-driven trophic association of sulfur-cycling microorganisms and the subsequent microbial activation and diversification, triggering the restoration of the marine ecosystem function.

Effective Se reduction by lactate-stimulated indigenous microbial communities in excavated waste rocks.

Waste rocks generated from tunnel excavation contain the metalloid selenium (Se) and its concentration sometimes exceeds the environmental standards. The possibility and effectiveness of dissolved Se removal by the indigenous microorganisms are unknown. Chemical analyses and high-throughput 16S rRNA gene sequencing were implemented to investigate the functional and structural responses of the rock microbial communities to the Se and lactate amendment. During anaerobic incubation of the amended rock slurries from two distinct sites, dissolved Se concentrations decreased significantly, which coincided with lactate degradation to acetate and/or propionate. Sequencing indicated that relative abundances of Desulfosporosinus burensis increased drastically from 0.025 % and 0.022% to 67.584% and 63.716 %, respectively, in the sites. In addition, various Desulfosporosinus spp., Symbiobacterium-related species and Brevibacillus ginsengisoli, as well as the Se(VI)-reducing Desulfitobacterium hafniense, proliferated remarkably. They are capable of incomplete lactate oxidation to acetate as only organic metabolite, strongly suggesting their involvement in dissimilatory Se reduction. Furthermore, predominance of Pelosinus fermentans that ferments lactate to propionate and acetate implied that Se served as the electron sink for its fermentative lactate degradation. These results demonstrated that the indigenous microorganisms played vital roles in the lactate-stimulated Se reduction, leading to the biological Se immobilization treatment of waste rocks.

Microbial community in an anaerobic membrane bioreactor and its performance in treating organic solid waste under controlled and deteriorated conditions.

The adoption of anaerobic membrane bioreactors (AnMBRs) for organic solid waste management is important for the recovery of energy and high-quality treated water. However, few studies have focused on AnMBR treatment of high-strength organic solid waste and the microorganisms involved under deteriorated operating conditions. In the present study, a 15-L bench-scale AnMBR was operated using a model slurry of high-strength organic solid waste with the organic loading rate (OLR) increasing from 2.3 g chemical oxygen demand (COD) L-1 day-1 (represented as a controlled condition) to 11.6 g COD L-1 day-1 (represented as a deteriorated condition), and microbial community dynamics over 120 days of operation were analyzed. The abundances of methanogens and bacteria that were dominant under the controlled condition decreased as a result of both high organic loading and sludge withdrawal under the deteriorated condition and did not recover thereafter. Instead, numbers of putative volatile fatty acid (VFA)-producing bacterial operational taxonomic units (OTUs) related to the genus Prevotella increased rapidly, reaching a relative abundance of 43.2%, leading to the deterioration of methanogenic AnMBR operation. Considering that the sequences of these OTUs exhibited relatively low sequence identity (91-95%) to those of identified Prevotella species, the results strongly suggest that the accumulation of VFAs by novel VFA-producing bacteria in the digestion sludge promotes the disruption of the methanogen community under deteriorated conditions.

Unexpected diversity of acetate degraders in anaerobic membrane bioreactor treating organic solid waste revealed by high-sensitivity stable isotope probing.

In anaerobic membrane bioreactor (AnMBR) treating organic solid waste, acetate is one of the most important precursors to CH4. However, the identity and diversity of anaerobic acetate degraders are largely unknown, possibly due to their slow growth rates and low abundances. Here, we identified acetate-degrading microorganisms in the AnMBR sludges by high-sensitivity stable isotope probing. Degradation of the amended 13C-acetate coincided with production of 13CH4 and 13CO2 during the sludge incubation. High-throughput sequencing of RNA density fractions indicated that the aceticlastic and hydrogenotrophic methanogens, i.e., Methanosaeta sp. (acetate dissimilator) and Methanolinea sp. (acetate assimilator), incorporated 13C-acetate significantly. Remarkably, 22 bacterial species incorporating 13C-acetate were identified, whereas their majority was distantly related to the cultured representatives. Only two of them were the class Deltaproteobacteria-affiliated lineages with syntrophic volatile fatty acid oxidation activities. Phylogenetic tree analysis and population dynamics tracing revealed that novel species of the hydrolyzing and/or fermenting taxa, such as the phyla Bacteroidetes, Chloroflexi and Lentisphaerae, exhibited low relative abundances comparable to that of Methanolinea sp. (0.00011%) during the AnMBR operation, suggesting that these bacteria were involved in anaerobic acetate assimilation. Meanwhile, novel species of the phyla Firmicutes, Synergistetes and Caldiserica, the candidate phyla Aminicenantes and Atribacteria and the candidate division GOUTA4-related clade, as well as the known Deltaproteobacteria members, existed at relatively high abundances (0.00031%-0.31121%) in the reactor, suggesting that these bacterial species participated in anaerobic dissimilation of acetate, e.g., syntrophic acetate oxidation. The results of this study demonstrated the unexpected diversity and ecophysiological features of the anaerobic acetate degraders in the AnMBR treating organic solid waste.

Clarifying prokaryotic and eukaryotic biofilm microbiomes in anaerobic membrane bioreactor by non-destructive microscopy and high-throughput sequencing.

Anaerobic membrane bioreactor (AnMBR) is used for the treatment of organic solid waste. Clogging of filtration membrane pores, called membrane fouling, is one of the most serious issues for the sustainable operation of AnMBR. Although the physical and chemical mechanisms of the membrane fouling have been widely studied, the biological mechanisms are still unclear. The biofilm formation and development on the membrane might cause the membrane fouling. In this study, the prokaryotic and eukaryotic microbiomes of the membrane-attached biofilms in an AnMBR treating a model slurry of organic solid waste were investigated by non-destructive microscopy and high-throughput sequencing of 16S and 18S rRNA genes. The non-destructive visualization indicated that the biofilm was layered with different structures. The lowermost residual fouling layer was mesh-like and composed of filamentous microorganisms, while the upper cake layer was mainly the non-dense and non-cell region. The principal coordinate and phylogenetic analyses of the sequence data showed that the biofilm microbiomes were different from the sludge. The lowermost layer consisted of operational taxonomic units that were related to Leptolinea tardivitalis and Methanosaeta concilii (9.53-10.07% and 1.14-1.64% of the total prokaryotes, respectively) and Geotrichum candidum (30.22-82.31% of the total eukaryotes), all of which exhibited the filamentous morphology. Moreover, the upper layer was inhabited by the presumably cake-degrading bacteria and predatory eukaryotes. The biofilm microbiome features were consistent with the microscope-visualized structure. These results demonstrated that the biofilm structure and microbiome were the layer specific, which provides better understanding of biological mechanisms of membrane fouling in the AnMBR.

Transition of microbial community structures after development of membrane fouling in membrane bioreactors (MBRs).

Although membrane fouling is a major issue when operating membrane bioreactors (MBRs), information regarding MBR performance and the sludge microbiome after the development of fouling remains limited. For the present study, two MBRs were operated for approximately 1 month under conditions of membrane fouling to investigate the effects of highly stressed environments on the sludge microbiome. After the development of fouling, a Collimonas-related operational taxonomic unit (OTU) was highly dominant in both reactors (relative abundances were ⁓ 63%) and this predomination caused a precipitous decline in the diversity indices of the sludge microbiomes. Because the excessive predomination by limited numbers of OTUs can lead to reductions in the adaptability to environmental changes, monitoring microbial diversity may be a valuable indicator for maintaining the robustness of a sludge microbiome. While, the decrease in the abundance of the Collimonas-related OTU resulted in the predomination of distinct microorganisms in each of the reactors despite being operated under the same conditions; this finding indicates existence of strong pressure to perturb the microbiomes. Detailed analyses suggested that the availability of terminal electron acceptors and competitive interactions between microbes via the secretion of extracellular proteins appeared to differentiate the structures of the respective microbial communities. During the extracellular proteins were secreted in the sludge, considerable portion of microbes were dead and large amounts of biomolecules seemed to be released; resultantly facilitated the predomination of fermentative anaerobes in one reactor as they use organic substances but not inorganic terminal electron acceptors to generate ATP under anaerobic conditions.

Effects of the Wastewater Flow Rate on Interactions between the Genus Nitrosomonas and Diverse Populations in an Activated Sludge Microbiome.

The present study characterized the interactions of microbial populations in activated sludge systems during the operational period after an increase in the wastewater flow rate and consequential ammonia accumulation using a 16S rRNA gene sequencing-based network analysis. Two hundred microbial populations accounting for 81.8% of the total microbiome were identified. Based on a co-occurrence analysis, Nitrosomonas-type ammonia oxidizers had one of the largest number of interactions with diverse bacteria, including a bulking-associated Thiothrix organism. These results suggest that an increased flow rate has an impact on constituents by changing ammonia concentrations and also that Nitrosomonas- and Thiothrix-centric responses are critical for ammonia removal and microbial community recovery.

Microbiomes and chemical components of feed water and membrane-attached biofilm in reverse osmosis system to treat membrane bioreactor effluents.

Reverse osmosis (RO) system at a stage after membrane bioreactor (MBR) is used for the wastewater treatment and reclamation. One of the most serious problems in this system is membrane fouling caused by biofilm formation. Here, microbiomes and chemical components of the feed water and membrane-attached biofilm of RO system to treat MBR effluents were investigated by non-destructive confocal reflection microscopy, excitation-emission fluorescence spectroscopy and high-throughput sequencing of 16S rRNA genes. The microscopic visualization indicated that the biofilm contained large amounts of microbial cells (0.5 ± 0.3~3.9 ± 2.3 µm3/µm2) and the extracellular polysaccharides (3.3 ± 1.7~9.4 ± 5.1 µm3/µm2) and proteins (1.0 ± 0.2~1.3 ± 0.1 µm3/µm2). The spectroscopic analysis identified the humic and/or fulvic acid-like substances and protein-like substances as the main membrane foulants. High-throughput sequencing showed that Pseudomonas spp. and other heterotrophic bacteria dominated the feed water microbiomes. Meanwhile, the biofilm microbiomes were composed of diverse bacteria, among which operational taxonomic units related to the autotrophic Hydrogenophaga pseudoflava and Blastochloris viridis were abundant, accounting for up to 22.9 ± 4.1% and 3.1 ± 0.4% of the total, respectively. These results demonstrated that the minor autotrophic bacteria in the feed water played pivotal roles in the formation of polysaccharide- and protein-rich biofilm on RO membrane, thereby causing membrane fouling of RO system.

Architecture, component, and microbiome of biofilm involved in the fouling of membrane bioreactors.

Biofilm formation on the filtration membrane and the subsequent clogging of membrane pores (called biofouling) is one of the most persistent problems in membrane bioreactors for wastewater treatment and reclamation. Here, we investigated the structure and microbiome of fouling-related biofilms in the membrane bioreactor using non-destructive confocal reflection microscopy and high-throughput Illumina sequencing of 16S rRNA genes. Direct confocal reflection microscopy indicated that the thin biofilms were formed and maintained regardless of the increasing transmembrane pressure, which is a common indicator of membrane fouling, at low organic-loading rates. Their solid components were primarily extracellular polysaccharides and microbial cells. In contrast, high organic-loading rates resulted in a rapid increase in the transmembrane pressure and the development of the thick biofilms mainly composed of extracellular lipids. High-throughput sequencing revealed that the biofilm microbiomes, including major and minor microorganisms, substantially changed in response to the organic-loading rates and biofilm development. These results demonstrated for the first time that the architectures, chemical components, and microbiomes of the biofilms on fouled membranes were tightly associated with one another and differed considerably depending on the organic-loading conditions in the membrane bioreactor, emphasizing the significance of alternative indicators other than the transmembrane pressure for membrane biofouling.

Role of membrane fouling substances on the rejection of N-nitrosamines by reverse osmosis.

The impact of fouling substances on the rejection of four N-nitrosamines by a reverse osmosis (RO) membrane was evaluated by characterizing individual organic fractions in a secondary wastewater effluent and deploying a novel high-performance liquid chromatography-photochemical reaction-chemiluminescence (HPLC-PR-CL) analytical technique. The HPLC-PR-CL analytical technique allowed for a systematic examination of the correlation between the fouling level and the permeation of N-nitrosamines in the secondary wastewater effluent and synthetic wastewaters through an RO membrane. Membrane fouling caused by the secondary wastewater effluent led to a notable decrease in the permeation of N-nitrosodimethylamine (NDMA) while a smaller but nevertheless discernible decrease in the permeation of N-nitrosomethylethylamine (NMEA), N-nitrosopyrrolidine (NPYR) and N-nitrosomorpholine (NMOR) was also observed. Fluorescence spectrometry analysis revealed that major foulants in the secondary wastewater effluent were humic and fulvic acid-like substances. Analysis using the size exclusion chromatography technique also identified polysaccharides and proteins as additional fouling substances. Thus, further examination was conducted using solutions containing model foulants (i.e., sodium alginate, bovine serum albumin, humic acid and two fulvic acids). Similar to the secondary wastewater effluent, membrane fouling with fulvic acid solutions resulted in a decrease in N-nitrosamine permeation. In contrast, membrane fouling with the other model foulants resulted in a negligible impact on N-nitrosamine permeation. Overall, these results suggest that the impact of fouling on the permeation of N-nitrosamines by RO is governed by specific small organic fractions (e.g. fulvic acid-like organics) in the secondary wastewater effluent.

Expression of human Gaucher disease gene GBA generates neurodevelopmental defects and ER stress in Drosophila eye.

Gaucher disease (GD) is the most common of the lysosomal storage disorders and is caused by defects in the GBA gene encoding glucocerebrosidase (GlcCerase). The accumulation of its substrate, glucocylceramide (GlcCer) is considered the main cause of GD. We found here that the expression of human mutated GlcCerase gene (hGBA) that is associated with neuronopathy in GD patients causes neurodevelopmental defects in Drosophila eyes. The data indicate that endoplasmic reticulum (ER) stress was elevated in Drosophila eye carrying mutated hGBAs by using of the ER stress markers dXBP1 and dBiP. We also found that Ambroxol, a potential pharmacological chaperone for mutated hGBAs, can alleviate the neuronopathic phenotype through reducing ER stress. We demonstrate a novel mechanism of neurodevelopmental defects mediated by ER stress through expression of mutants of human GBA gene in the eye of Drosophila.

Physical properties of self-assembled monolayers of Mercapto Oligo (ethylene oxide) methyl ether on gold.

Physical properties (chemical adsorption rate, viscoelasticity, thickness, and conformation) for self-assembled monolayers (SAMs) of mercapto oligo (ethylene oxide) methyl ethers on gold were determined by quartz crystal microbalance (QCM). The values of thickness, shear viscosity and elastic shear modulus of SAMs increase with unit number of oligo (ethylene oxide) segment. However, the chemical adsorption rate determined by a Langmuir isotherm does not show such a unit number regularity. Those results suggest that difference in unit number of oligo (ethylene oxide) segment can significantly affects physical properties of SAMs.

Dynamic properties of the polyethylene glycol molecules on the oscillating solid-liquid interface.

The dynamic properties of polyethylene glycol (PEG) molecules on the solid-liquid interface oscillating at MHz were investigated using the quartz crystal microbalance (QCM). The number-average molecular weights (M(n)) of the PEG molecules were systematically varied over 4 orders of magnitude. This study makes it clear that the series-resonant frequency shift, ΔF, of the QCM against the square root of the density-viscosity product of the PEG solution is linear and has the intercept. Moreover, systematical analysis reveals that the ΔF slope rapidly decreases with M(n) and that the ΔF intercept becomes constant above 4.0×10(3) g mol(-1). As a result, those reveal that the resonant length of the PEG molecule moving with the oscillating plate of 9 MHz is 54.2 Å. We also find that the behaviors of ΔF due to M(n) are mainly caused by the length of the PEG molecule.

Surface plasmon resonance-based trace detection of small molecules by competitive and signal enhancement immunoreaction.

A surface plasmon resonance (SPR)-immunosensor for detection of the low molecular weight compound 2,4-dinitorophenol (DNP) at ultra-low concentration has been developed. The sensor strategy is based on a competitive immunoreaction between DNP and a DNP-protein conjugate, namely DNP-bovine serum albumin conjugate (DNP-BSA). Anti-DNP monoclonal antibody was immobilized on a gold thin-film coated SPR-sensor chip by means of a chemical coupling process. DNP-BSA, on contact with the anti-DNP antibody immobilized SPR-immunosensor chip causes an increase in the resonance angle of the sensor chip. The optimum concentration of immobilized antibody on the SPR-sensor chip is 100 microg mL(-1). The SPR-immunosensor response for free DNP determination using the competitive immunoreaction had a response time of ca. 15 min. Using this method, DNP could be determined in the concentration range 1 ppt to 1 ppb. The SPR signal for ppt levels of DNP was enhanced by a factor of three by subsequently treating immuno-bound DNP-BSA with a secondary anti-DNP antibody.

Adsorption of 125I-labeled immunoglobulin G, its F(ab')2 and Fc fragments onto plasma-polymerized films.

Plasma-polymerized films were formed on flat glass plates using allylamine, acrylic acid, acrolein, and allylcyanide as monomers. Adsorption of (125)I-labeled-proteins such as immunoglobulin G (IgG), its F(ab')(2) and Fc fragments, and human serum albumin (HSA) was measured on these plasma-polymerized (PP) films covering the glass plates and on commercially available polymer plates. The adsorption isotherm followed the Langmuir equation, from which the binding constant and amount of saturation binding were estimated. We found that, in general, a cationic surface had higher affinity for protein adsorption than an anionic surface. Among the surfaces examined, the PP-allylamine surface showed the highest binding capacity (264.2 nmol/m(2)) for F(ab')(2) fragment: it was remarkably high. Of the surfaces examined, the PP-acrylic acid surface showed the lowest binding capacity (12.8 nmol/m(2)) for F(ab')(2) fragment. The PP-acrylic acid surface also indicated the lowest protein binding capacity for IgG (16.5 nmol/m(2)), Fc-IgG (32.4 nmol/m(2)) and HSA (16.7 nmol/m(2)), respectively. These imply that the PP-acrylic acid film is useful to fabricate as a low protein adsorption material which expected to decrease cell adhesion. Results of our investigation indicate that the plasma-polymerization technique is promising for fabrication of a smart NanoBio-interface which can control the protein adsorption on a solid-phase substrate using a suitable monomer such as allylamine for the large adsorption and acrylic acid for the small adsorption.

Quartz crystal microbalance immunosensors for environmental monitoring.

This paper presents discussion of quartz crystal microbalance (QCM) immunosensors for environmental monitoring. Factors limiting the practical application of antibodies to analytical problems are also presented. Among several candidates for the QCM immunosensor device, selected QCM devices and oscillating circuits were tested thoroughly and developed to obtain highly stable and sensitive frequency signals. The biointerface of QCM immunosensor was designed and controlled to immobilize antibody on the QCM surface, to reduce non-specific binding and to suppress denaturation of immobilizing antibody by self-assembled monolayer technique and artificial phospholipid (2-methacryloyloxyethyl phosphorylcholine (MPC)) polymer. MPC polymer as a antibody-stabilizing reagent was added to reduce non-specific binding of the antigen solution and stabilize the immunologic activity of the antibody-immobilized QCM. In addition, it provides examples for detection and quantitation of environmental samples using QCM immunosensors. The analytical results for fly ash extracted samples of dioxins using the QCM immunosensor indicated a good relationship with GC/MS methods. The integrating protocols of the competitive immunoassay and signal-enhancing step are for detecting low molecular analytes with extremely low detection limits using an QCM immunosensor. Furthermore, its detect limitation was extended from 0.1 to 0.01 ng/ml by the signal-enhancing step when the anti-bisphenol-A antibody conjugated MPC polymeric nanoparticles was used. The QCM immunosensor method has demonstrated its effectiveness as an alternative screening method for environmental monitoring because these results were compared with results obtained through environmental monitoring methods such as ELISA and GC/MS.

Dioxin immunosensor using anti-2,3,7,8-TCDD antibody which was produced with mono 6-(2,3,6,7-tetrachloroxanthene-9-ylidene) hexyl succinate as a hapten.

To detect dioxin using a quartz crystal microbalance (QCM) immunosensor, anti-2,3,7,8-tetrachloro-p-dibenzodioxin (TCDD) monoclonal antibodies (MAbs) were produced as types of IgG1 and IgM, with mono 6-(2,3,6,7-tetrachloroxanthene-9-ylidene) hexyl succinate (as a hapten) conjugated with bovine serum albumin (dioxin-BSA). Furthermore, ScFv was generated from hybridoma-producing IgG1 MAb. Among these antibodies, ScFv showed excellent capability for dioxin detection using QCM immunosensors.