Optical OFDM for SiPM-Based Underwater Optical Wireless Communication Links.

Underwater optical wireless systems have dual requirements of high data rates and long ranges in harsh scattering and attenuation conditions. In this paper, we investigate the advantages and limitations of optical orthogonal frequency-division multiplexing (O-OFDM) signaling when a silicon photo-multiplier (SiPM) is used at the receiver in order to ensure high sensitivity. Considering a light-emitting diode (LED) transmitter and taking into account the limited dynamic range imposed by the transmitter and the SiPM receiver, we study the performance of three popular O-OFDM schemes, i.e., DC-biased, asymmetrically-clipped, and layered asymmetrically-clipped O-OFDM (DCO-, ACO-, and LACO-OFDM, respectively). We consider a constraint on transmit electrical power PTxe and take into account the required DC bias for the three considered schemes in practice, showing the undeniable advantage of ACO- and LACO-OFDM in terms of energy efficiency. For instance, for the considered SiPM and LED components, a spectral efficiency of ∼1 bps/Hz with a data rate of 20 Mbps, a link range of 70 m, and a target bit-error-rate (BER) of 10-3, ACO and LACO allow a reduction of about 10 and 6 mW, respectively, in the required PTxe, compared to DCO-OFDM. Meanwhile, we show that when relaxing the PTxe constraint, DCO-OFDM offers the largest operational link range within which a target BER can be achieved. For instance, for a target BER of 10-3 and a data rate of 20 Mbps, and considering PTxe of 185, 80, and 50 mW for DCO-, LACO-, and ACO-OFDM, respectively, the corresponding intervals of operational link range are about 81, 74.3, and 73.8 m. Lastly, we show that LACO-OFDM makes a good compromise between energy efficiency and operational range flexibility, although requiring a higher computational complexity and imposing a longer latency at the receiver.

Giant ultrafast optical nonlinearities of annealed Sb2Te3 layers.

The optimization of thin Sb2Te3 films in order to obtain giant ultrafast optical nonlinearities is reported. The ultrafast nonlinearities of the thin film layers are studied by the Z-scan technique. Giant saturable absorption is obtained, which is the highest ever reported, by means of the Z-scan technique.

Taking advantage of acoustic inhomogeneities in photoacoustic measurements.

This paper proposes a method for improving the localization and the quantification of the optical parameters in photoacoustic (PA) tomography of biological tissues that are intrinsically heterogeneous in both optical and acoustic properties. It is based on the exploitation of both the PA signal, generated by the heterogeneous optical structures, and the secondary acoustic echoes due to the interaction between a primary PA wave generated near the tissue surface and the heterogeneous acoustic structures. These secondary echoes can also be collected through proper measurements of the PA signals. The experimental procedure is presented along with the method to filter the signal and the reconstruction algorithm that includes the account of the acoustic information.

Nanosecond Z-scan measurements of the nonlinear refractive index of fused silica.

We present the results of Z-scan studies carried out on fused silica at 1064nm and 532nm with two different nanosecond pulse durations. Such measurements in silica and in the nanosecond regime are possible thanks to a high sensitivity setting up of the Z-scan method and in-situ characterizations of the spatio-temporal parameters of the beam. Besides, with the use of a newly adapted numerical simulation only the calibration errors of the measurement devices are significant. In these conditions, we found a higher value of the nonlinear refractive index than in the femtosecond regime and we show that these values depend on pulse duration, which indicates the contribution of nanosecond mechanisms like electrostriction.

Laser-induced damage of materials in bulk, thin-film, and liquid forms.

Accurate threshold curves of laser-induced damage (7-ns single shot at 1.064 microm) are measured in bulk and at the surfaces of optical components such as substrates, thin films, multilayers, and liquids. The shapes and the slopes of the curves are related to the spot size and to the densities of the nanodefects that are responsible for damage. First, these densities are reported for bulk substrates. In surfaces and films the recorded extrinsic and intrinsic threshold curves permit the discrimination of the effects of microdefects and nanodefects. In all cases the density of nanocenters is extracted by means of a phenomenological approach. Then we test liquids and mixtures of liquids with controlled defect densities. The results emphasize the agreement between measurement and prediction and demonstrate the validity of the presence of different kinds of nanocenter as the precursors of laser damage.