ABSTRACT
El objetivo de este estudio fue comparar la fidelidad de copia y estabilidad dimensional entre modelos de resina epóxica y modelos de yeso (Fuji Rock EP - GC Europe; Implant Stone - Polidental). Fue realizada la impresión de una matriz de acero para obtener 30 especímenes (n=10). La matriz simulaba dos piezas dentarias talladas para recibir coronas totales, sobre éstas fueron adaptados dos copings metálicos con aletas horizontales. Se evaluó al microscopio (Microscopio Measurescope, Nikon) la distancia entre el coping y la línea de terminación de las piezas talladas (en adelante, "desadaptación vertical") y la distancia entre las aletas horizontales de los copings (en adelante, "desadaptación horizontal"), las medidas obtenidas entre la matriz de acero y copings metálicos fueron consideradas como grupo control. Los copings metálicos fueron después adaptados sobre los modelos de yeso y sobre la resina experimental y fue realizada la evaluación al microscopio del mismo modo que el descrito anteriormente. Fueron realizadas 3 mediciones en dos tiempos (24 y 48 horas). Respecto a la desadaptación horizontal, el yeso FujiRock presentó una mejor estabilidad dimensional después de 24 horas, ya que la desadaptación fue similar estadísticamente a la desadaptación de la matriz (control) (p>0,05). Después de 48 horas, todos los grupos presentaron valores similares a la matriz (p>0,05). Respecto a la desadaptación vertical, todos los materiales presentaron diferencia estadísticamente significante en relación a la matriz (p?0,05), sin embargo, no hubo diferencia entre los materiales evaluados (p>0,05). La resina epóxica experimental puede ser una alternativa viable para la obtención de modelos odontológicos...
The aim of this study was to compare the accuracy of surface detail reproduction and dimensional stability of casts made from an experimental epoxy resin and gypsum (Fuji Rock EP - GC Europe; Implant Stone - Polidental). A steel matrix was molded to obtain 30 cast samples (n=10). The matrix simulated two teeth prepared to receive total crowns on which two metal copings with horizontal flaps were adapted. Three readings were performed (Measurescope microscope, Nikon) in order to measure the vertical and horizontal misfit and those readings were used as control. Metal copings were adapted over the gypsum and epoxy resin casts and three measurements were made in two periods (24 and 48 hours). Regarding the horizontal misfit, Fujirock had better dimensional stability after 24 hours, being statistically similar to the matrix (p> 0.05). After 48 hours, all groups had statistically similar values to the matrix (p> 0.05). Regarding the vertical misfit, all materials were statistically different in relation to the matrix (p ? 0.05). However, there was no statistically significant difference between the materials evaluated (p> 0.05). The experimental epoxy resin could be a suitable alternative to obtain dental casts...
Subject(s)
Humans , Calcium Sulfate , Dental Impression Technique , Epoxy Resins , Dental Arch , Dental Materials , Denture DesignABSTRACT
OBJECTIVE: To evaluate the color stability and surface roughness of 3 dental composites subjected to cigarette smoke and brushing. METHODS: Twenty specimens were prepared for each type of restorative material used: nanohybrid (Tetric N-Ceram); hybrid (Z250-3M ESPE) and silorane-based microhybrid (Filtek P90-3M ESPE), which were divided into 2 groups (n=10), according to the type of finishing/polishing received: Group 1 - papers with decreasing abrasive grit and Group 2 - polyester matrix (without polishing). After initial readouts of color (Easy Shade-VITA) and surface roughness (SJ-201P Mitutoyo), specimens were subjected to action of smoke from 20 cigarettes, (Marlboro Red-Philip Morris). After each cigarette, the samples were submitted to brushing in a standardised device. After this, final readouts were taken to calculate change in color (ΔE and ΔL) and roughness (ΔRa), which were statistically analysed (2-way ANOVA, Bonferroni, and Student's-t tests respectively, p<0.05). RESULTS: Tetric N-Ceram presented color change at clinically unacceptable levels (ΔE>3.3) when the polyester strip was used for finishing, a result differing (p<0.05) from those of the other composites, which presented no difference between them (p>0.05). Unpolished composites presented higher Ra values than those that were polished (p<0.05), with exception of the silorane based composite. CONCLUSION: Absence of polishing increases cigarette capacity to stain composites and surface roughness of composites, with exception of the silorane based type.
Subject(s)
Composite Resins/chemistry , Dental Materials/chemistry , Nicotiana , Smoke , Algorithms , Bisphenol A-Glycidyl Methacrylate/chemistry , Color , Dental Polishing/methods , Methacrylates/chemistry , Nanocomposites/chemistry , Polyesters/chemistry , Polyethylene Glycols/chemistry , Polymethacrylic Acids/chemistry , Polyurethanes/chemistry , Silorane Resins/chemistry , Surface Properties , Toothbrushing/instrumentationABSTRACT
This study evaluated the colour stability of temporary prosthetic restorations with different thicknesses submitted to artificial accelerated aging. The occlusal surfaces of 40 molars were grinded to obtain flat enamel surfaces. Twenty acrylic resin specimens [Polymethyl methacrylate (Duralay) and Bis-methyl acrylate (Luxatemp)] were made with two different thicknesses, 0.5 mm and 1.0 mm. Temporary restorations were fixed on enamel and CIE L*a*b* colour parameters of each specimen were assessed before and after artificial accelerated aging. All groups showed colour alterations above the clinically acceptable limit. Luxatemp showed the lowest colour alteration regardless its thickness and Duralay showed the greatest alteration with 0.5 mm.
