Preparation, characterization, and performance of PES/GO woven mixed matrix nanocomposite forward osmosis membrane for water desalination.

Mixed matrix woven forward osmosis (MMWFO) membranes made of polyethersulfone (PES)/graphene oxide nanosheets (GO NSs) were made by inserting varying wt% ratios of GO NSs (zero to 0.1 wt%) into the PES matrix. A coated woven fabric material was used to cast the membrane polymer solution. The physical characteristics and chemical structures of the produced PES/GO MMWFO membranes were studied, including contact angle, hydrophilicity, porosity, tortuosity, function groups, chemical and crystallographic structures, nanomorphologies, and surface roughness. The performance of the prepared PES/GO FO membranes for water desalination was evaluated in terms of pure water flux (J w), reverse salt flux (J s), and salt rejection (SR). The hydrophilicity and porosity of the FO membrane improved with the addition of GO NSs, as did water permeability due to the development of multiple skin-layer structures with greater GO NS loading. These GO NSs establish shortcut pathways for water molecules to move through, reducing support layer tortuosity by three times, lowering support layer structural features, and minimizing internal concentration polarization (ICP). The PES/0.01 wt% GO MMWFO membrane with a total casting thickness of 215 µm and 1 M NaCl concentration had the best performance, with the highest J w (114.7 LMH), lowest J s (0.03 GMH), and lowest specific reverse solute flux (J s/J w = 0.00026 g L-1), as well as a more favorable structural parameter (S = 149 µm). The performance of our optimized membrane is significantly better than that of the control woven commercial cellulose triacetate (CTA) FO membrane under optimal FO conditions. As the NaCl concentration increased from 0.6 to 2 M, J w increased from 105 to 127 LMH which is much higher than the J w of the commercial one (7.2 to 15 LMH). Our FO membranes have an SR of 99.2%@0.65 M NaCl, which is significantly greater than that of the CTA membrane.

Nanostructured MoS2 and WS2 Photoresponses under Gas Stimuli.

This study was on the optoelectronic properties of multilayered two-dimensional MoS2 and WS2 materials on a silicon substrate using sputtering physical vapor deposition (PVD) and chemical vapor deposition (CVD) techniques. For the first time, we report ultraviolet (UV) photoresponses under air, CO2, and O2 environments at different flow rates. The electrical Hall effect measurement showed the existence of MoS2 (n-type)/Si (p-type) and WS2 (P-type)/Si (p-type) heterojunctions with a higher sheet carrier concentration of 5.50 × 105 cm-2 for WS2 thin film. The IV electrical results revealed that WS2 is more reactive than MoS2 film under different gas stimuli. WS2 film showed high stability under different bias voltages, even at zero bias voltage, due to the noticeably good carrier mobility of 29.8 × 102 cm2/V. WS2 film indicated a fast rise/decay time of 0.23/0.21 s under air while a faster response of 0.190/0.10 s under a CO2 environment was observed. Additionally, the external quantum efficiency of WS2 revealed a remarkable enhancement in the CO2 environment of 1.62 × 108 compared to MoS2 film with 6.74 × 106. According to our findings, the presence of CO2 on the surface of WS2 improves such optoelectronic properties as photocurrent gain, photoresponsivity, external quantum efficiency, and detectivity. These results indicate potential applications of WS2 as a photodetector under gas stimuli for future optoelectronic applications.

Fabrication and Characterization of Nanostructured Rock Wool as a Novel Material for Efficient Water-Splitting Application.

Rock wool (RW) nanostructures of various sizes and morphologies were prepared using a combination of ball-mill and hydrothermal techniques, followed by an annealing process. Different tools were used to explore the morphologies, structures, chemical compositions and optical characteristics of the samples. The effect of initial particle size on the characteristics and photoelectrochemical performance of RW samples generated hydrothermally was investigated. As the starting particle size of ball-milled natural RW rises, the crystallite size of hydrothermally formed samples drops from 70.1 to 31.7 nm. Starting with larger ball-milled particle sizes, the nanoparticles consolidate and seamlessly combine to form a continuous surface with scattered spherical nanopores. Water splitting was used to generate photoelectrochemical hydrogen using the samples as photocatalysts. The number of hydrogen moles and conversion efficiencies were determined using amperometry and voltammetry experiments. When the monochromatic wavelength of light was increased from 307 to 460 nm for the manufactured RW>0.3 photocatalyst, the photocurrent density values decreased from 0.25 to 0.20 mA/mg. At 307 nm and +1 V, the value of the incoming photon-to-current efficiency was ~9.77%. Due to the stimulation of the H+ ion rate under the temperature impact, the Jph value increased by a factor of 5 when the temperature rose from 40 to 75 °C. As a result of this research, for the first time, a low-cost photoelectrochemical catalytic material is highlighted for effective hydrogen production from water splitting.

Removal of Scale-Forming Ions and Oil Traces from Oil Field Produced Water Using Graphene Oxide/Polyethersulfone and TiO2 Nanoribbons/Polyethersulfone Nanofiltration Membranes.

Treatment of produced water in oil fields has become a tough challenge for oil producers. Nanofiltration, a promising method for water treatment, has been proposed as a solution. The phase inversion technique was used for the synthesis of nanofiltration membranes of polyethersulfone embedded with graphene oxide nanoparticles and polyethersulfone embedded with titanium nanoribbons. As a realistic situation, water samples taken from the oil field were filtered using synthetic membranes at an operating pressure of 0.3 MPa. Physiochemical properties such as water flux, membrane morphology, flux recovery ratio, pore size and hydrophilicity were investigated. Additionally, filtration efficiency for removal of constituent ions, oil traces in water removal, and fouling tendency were evaluated. The constituent ions of produced water act as the scaling agent which threatens the blocking of the reservoir bores of the disposal wells. Adding graphene oxide (GO) and titanium nanoribbons (TNR) to polyethersulfone (PES) enhanced filtration efficiency, water flux, and anti-fouling properties while also boosting hydrophilicity and porosity. The PES-0.7GO membrane has the best filtering performance, followed by the PES-0.7TNR and pure-PES membranes, with chloride salt rejection rates of 81%, 78%, and 35%; oil rejection rates of 88%, 85%, and 71%; and water fluxes of 85, 82, and 42.5 kg/m2 h, respectively. Because of its higher hydrophilicity and physicochemical qualities, the PES-0.7GO membrane outperformed the PES-0.7TNR membrane. Nanofiltration membranes embedded with nanomaterial described in this work revealed encouraging long-term performance for oil-in-water trace separation and scaling agent removal.

Characterization of the biosynthesized intracellular and extracellular plasmonic silver nanoparticles using Bacillus cereus and their catalytic reduction of methylene blue.

The biosynthesis of silver nanoparticles (Ag NPs) has been studied in detail using two different approaches. For the first time, Bacillus cereus is used for one-pot biosynthesis of capsulated Ag NPs, using both intracellular and extracellular approaches. To discriminate between the produced nanostructures by these two approaches, their structures, nanomorphologies, optical properties, hydrodynamic sizes and zeta potentials are studied using different techniques. Fourier-transform infrared spectroscopy was used to identify the bioactive components responsible for the reduction of Ag+ ions into Ag and the growth of stable Ag NPs. Scanning and transmission electron microscopy images displayed spherical and polygon nanomorphology for the intracellular and extracellular biosynthesized Ag NPs. For intracellular and extracellular biosynthesized Ag NPs, a face-centred cubic structure was observed, with average crystallite sizes of 45.4 and 90.8 nm, respectively. In comparison to the noncatalytic reduction test, the catalytic activities of intracellular and extracellular biosynthesized Ag NPs were explored for the reduction of highly concentrated MB dye solution. Extracellular Ag NPs achieved 100% MB reduction efficacy after around 80 min, compared to 50.6% and 24.1% in the presence and absence of intracellular Ag NPs, respectively. The rate of MB reduction was boosted by 22 times with the extracellular catalyst, and by 3 times with the intracellular catalyst. Therefore, the extracellular production process of Ag NPs utilizing Bacillus cereus bacteria might be applied in the industry as a cost-effective way for eliminating the toxic MB dye.

Sonophotocatalytic Dye Degradation Using rGO-BiVO4 Composites.

Reduced graphene oxide (rGO)/bismuth vanadate BiVO4 composites are fabricated with varied rGO amounts (0, 1, 2, and 3 wt%) through the synergetic effects of ultrasonication, photoinduced reduction, and hydrothermal methods, and the materials are tested as tools for sonophotocatalytic methylene blue (MB) dye degradation. The effect of rGO content on the sonophotocatalytic dye degradation capabilities of the composites are explored. Characterization of the proposed materials is done through transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transformation infrared spectroscopy as well as scanning electron microscopy. The coexistence of BiVO4 and rGO is confirmed using Raman spectroscopy and XRD. TEM confirms the existence of interfaces between rGO and BiVO4 and XPS affirms the existence of varied elemental oxidation states. In order to investigate the charge carriers transportation, time-dependent photocurrent responses of BiVO4 and 2 wt%- rGO/BiVO4 are done under visible light irradiation. The sonophotocatalytic MB dye degradation in an aqueous medium displays promising enhancement with rGO doping in rGO/BiVO4 composite. The 2 wt%- rGO/BiVO4 sample exhibits ≈52% MB dye degradation efficiency as compared to pure BiVO4 (≈25%) in 180 min of the sonophotocatalysis experiment. Phytotoxicity analysis through germination index is done using vigna radiata seeds.

Remarkable non-linear optical properties of gold cluster doped graphyne (GY): A DFT study.

The nonlinear optical (NLO) properties of gold (Au) doped graphyne (GY) complexes are the subject of this quantum mechanical investigation. Detailed profiling of GY@Aucenter, GY@Auside, GY@2Auabove,GY@2Auperpendicular, and GY@3Aucenter is accomplished at CAM-B3LYP/LANL2DZ. The differential influence of various GY based complexes on molecular geometry, vertical ionization energy (VIE), interaction energy (Eint), frontier molecular orbitals (FMOs), density of states (DOS), absorption maximum (λmax), molecular electrostatic potential (MEP), electron density distribution map (EDDM), transition density matrix (TDM), dipole moment (µ) and non-linear optical (NLO) properties have been investigated. Non-covalent interaction (NCI) analysis has been done to explore the sort of interactions in designed complexes. The vibrational frequencies are probed via infrared (IR) analysis. Doping tactics in all complexes dramatically changed charge carrier properties, such as shrinking band gap (Eg) and increasing λmax in the range of 3.97-5.58 eV and 288-562 nm respectively, compared to pure GY with 5.78 eV Eg and 265 nm λmax. When compared to GY (αO = 281.54 andßO = 0.21 au), GY@3Aucenter exhibited a significant increase in static mean polarizability (αO = 415 au) and the mean first hyperpolarizability (ßo = 3652 au) attributable to its lowest excitation energy (ΔE). GY doping has been discovered to be advantageous for designing potential nanoscale devices by focusing on the symphony between small Au clusters and GY and their impacts on NLO aspects.

A well-defined S-g-C3N4/Cu-NiS heterojunction interface towards enhanced spatial charge separation with excellent photocatalytic ability: synergetic effect, kinetics, antibacterial activity, and mechanism insights.

A well-defined heterojunction among two dissimilar semiconductors exhibited enhanced photocatalytic performance owing to its capability for boosting the photoinduced electron/hole pair transportation. Therefore, designing and developing such heterojunctions using diverse semiconductor-based materials to enhance the photocatalytic ability employing various approaches have gained research attention. For this objective, g-C3N4 is considered as a potential photocatalytic material for organic dye degradation; however, the rapid recombination rate of photoinduced charge carriers restricts the widespread applications of g-C3N4. Henceforth, in the current study, we constructed a heterojunction of S-g-C3N4/Cu-NiS (SCN/CNS) two-dimensional/one-dimensional (2D/1D) binary nanocomposites (NCs) by a self-assembly approach. XRD results confirm the construction of 22% SCN/7CNS binary NCs. TEM analysis demonstrates that binary NCs comprise Cu-NiS nanorods (NRs) integrated with nanosheets (NSs) such as the morphology of SCN. The observed bandgap value of SCN is 2.69 eV; nevertheless, the SCN/CNS binary NCs shift the bandgap to 2.63 eV. Photoluminescence spectral analysis displays that the electron-hole pair recombination rate in the SCN/CNS binary NCs is excellently reduced owing to the construction of the well-defined heterojunction. The photoelectrochemical observations illustrate that SCN/CNS binary NCs improve the photocurrent to ∼0.66 mA and efficiently suppress the electron-hole pairs when compared with that of undoped NiS, CNS and SCN. Therefore, the 22% SCN/7CNS binary NCs efficiently improved methylene blue (MB) degradation to 99% for 32 min under visible light irradiation.

Polyethersulfone Blended with Titanium Dioxide Nanoribbons/Multi-Wall Carbon Nanotubes for Strontium Removal from Water.

Nanofiltration methods were used and evaluated for strontium removal from wastewater. The phase inversion method was used to create a variety of polyethersulfone (PES)/TiO2 nanoribbons (TNRs)-multi-walled carbon nanotubes (MWCNTs) membranes with varied ratios of TNR-MWCNT nanocomposite. The hydrothermal technique was applied to synthesize the nanocomposite (TNRs-MWCNTs), which was then followed by chemical vapor deposition (CVD). The synthesized membranes were characterized by scanning electron microscopy (SEM), transmission electron microscopy, and FTIR. TNR macrovoids are employed as a support for the MWCNT growth catalyst, resulting in a TNR-MWCNT network composite. The hydrophilicity, mechanical properties, porosity, filtration efficiency of the strontium-containing samples, water flux, and fouling tendency were used to assess the performance of the synthesized membranes. The effect of feed water temperature on water flux was investigated as well as its effect on salt rejection. As the temperature increased from 30 to 90 °C, the salt rejection decreased from 96.6 to 82% for the optimized 0.7 PES/TNR-MWCNT membrane, whereas the water flux increased to ≈150 kg/m2. h. Double successive filtration was evaluated for its high efficiency of 1000 ppm strontium removal, which reached 82.4%.