Adsorption of Pb, Cu, and Ni Ions on Activated Carbon Prepared from Oak Cupules: Kinetics and Thermodynamics Studies.

Agricultural residue-activated carbon and biochar, inexpensive and environmentally friendly adsorbent materials, have recently received significant research attention. This study investigated the potential use of oak cupules in activated carbon form to remove widespread heavy metals (Pb2+, Cu2+, and Ni2+) from wastewater. The oak-activated carbon was prepared from oak cupules and activated with phosphoric acid. Oak-activated carbon was characterized using FTIR, BET analysis, energy-dispersive X-ray spectrometry (EDS), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The Freundlich, Langmuir, and Temkin isotherm models were used to assess the equilibrium data. The impact of various parameters, including pH effect, temperature, adsorbent dose, and contact time, was estimated. The Freundlich model was the most agreeable with Pb2+ adsorption by oak-based activated carbon, and Langmuir was more compatible with Cu2+ and Ni2+. Under optimum conditions, the average maximum removal was 63% Pb2+, 60% Cu2+, and 54% Ni2+ when every ion was alone in the aqueous solution. The removal was enhanced to 98% Pb2+, 72% Cu2+, and 60% Ni2+ when found as a mixture. The thermodynamic model revealed that the adsorption of ions by oak-based activated carbon is endothermic. The pseudo-second-order kinetic best describes the adsorption mechanism in this study; it verifies chemical sorption as the rate-limiting step in adsorption mechanisms. The oak-activated carbon was effective in removing Pb2+, Cu2+, and Ni2+ from wastewater and aqueous solutions.

Jordanian Kaolinite with TiO2 for Improving Solar Light Harvesting Used in Dye Removal.

TiO2-Kaolinite nanocomposite photocatalysts were synthesized using the sol-gel method, with titanium isopropoxide/HCl as reactants and Jordanian kaolinite clay as a support material. The samples' TiO2 content ranged from 10% to 70% (m/m). TiO2-Kaolinite composites were characterized using FTIR, SEM, XRF, and XRD. According to XRD measurements of the nano-composite samples, the intensity of the anatase peaks increased as the TiO2 percentage of the composition increased. As the percentage of TiO2 increased, so did the peaks of Ti-O-Si in FTIR. The extent of photocatalytic degradation of Congo-red dye was used to evaluate the photocatalytic activity of the prepared nanocomposites. After four hours under the sun, the percentage of Congo-red degradation ranged from 27 to 99 percent depending on the TiO2 content of the used nanocomposite. Meanwhile, the concentration drop in the dark did not exceed 10%. Photodegradation outperforms traditional treatment methods in terms of target degradation. Using naturally abundant materials such as clay in conjunction with metal oxides is widely regarded as an effective method of modifying the photoresponse properties of TiO2 particles, thereby improving solar light harvesting for target degradation.

Adsorption of Anionic and Cationic Dyes on Activated Carbon Prepared from Oak Cupules: Kinetics and Thermodynamics Studies.

In this study, activated carbon produced from oak cupules (ACOC) was prepared using chemical activation with H3PO4. ACOC is subsequently used as an adsorbent to facilitate the removal of an acidic dye, naphthol blue black (NBB), and basic dye crystal violet (CV) from aqueous solutions. The ACOC was characterized by FTIR spectroscopy, XRD, and SEM. The adsorption isotherm data fits well with the Langmuir model for NBB and CV. The kinetic models of adsorption of NBB and CV by ACOC were pseudo-first order and pseudo-second order, respectively. Thermodynamic parameters were evaluated and indicated that the adsorption of both dyes onto ACOC was endothermic and spontaneous. The adsorption capacity of ACOC reached 208 mg g-1 for NBB and 658 mg g-1 for CV. ACOC was shown to be a promising adsorbent for the removal of NBB and CV from aqueous solutions.

Adsorption Characteristics of Hair Dyes Removal from Aqueous Solution onto Oak Cupules Powder Coated with ZnO.

Three hair dyes of Arianor madder red 306003 (R), Arian or Straw Yellow 306005 (Y), and Arianor ebony 306020 (E) were removed from an aqueous solution in a batch mode using a powder of oak cupules coated with ZnO (COZ). The COZ-adsorbent material was characterized in terms of XRD, FT-IR, and SEM analysis. The best conditions for the uptake of hair dyes by COZ were investigated. For Y dye, the best uptake was estimated on 0.06 g of COZ at 7.0 pH for 150 min. The E dye uptake requires 120 min on 0.05 g of COZ at 9.0 pH. For E hair dye, kinetic data revealed a pseudo-first-order model for E hair dye and a pseudo-second-order model for R and Y. Equilibrium data exhibited consistency with the Langmuir isotherm model for the adsorption of E dye onto COZ, and the Freundlich isotherm model for the adsorption of R and Y hair dyes onto COZ. Isotherms models of D-R and Temkin were also examined. The thermodynamic parameters (-ve ∆G and +ve ∆H and ∆S) demonstrated that the removal of hair dyes by COZ is spontaneous, endothermic, and feasible. The adsorption capacity of COZ for R, Y, and E uptake was found to be 55.5, 52.6, and 135.1 mg·g-1, respectively. Furthermore, COZ reusability was demonstrated after five cycles of regeneration, with a negligible decline in adsorption extent (13.08%, 13.85, and 10.20% for R, Y, and E, respectively) in comparison to its initial capacity.