ABSTRACT
High moisture content is a recurrent problem in masonry and can jeopardize durability. Therefore, precise and easy-to-use techniques are welcome both to evaluate the state of conservation and to help in the diagnosis of moisture-related problems. In this research, the humidification and drying process of two wall specimens were assessed by infrared thermography and the results were compared with two traditional techniques: surface moisture meter and the gravimetric method. Two climatic chambers were used to impose different ambience conditions to each specimen, to evaluate the impact of air temperature and relative humidity in the results. The qualitative analysis of the thermal images allowed the identification of the phenomena. The quantitative analysis showed that the order of magnitude of the temperature gradient that translates high humidity levels is substantially different in the two chambers, pointing to the influence of the surrounding environment. The presented analysis contributes to identifying the criteria indicative of moisture-related problems in two different scenarios and discusses the correlation between the non-destructive techniques and the moisture content in the masonry walls. The limitations and future research gaps regarding the use of IRT to assess moisture are also highlighted.
Subject(s)
Thermography , Humidity , Temperature , Thermography/methodsABSTRACT
The radiant floor system market is growing rapidly because Europe is moving toward a low-carbon economy and increased awareness about environmental sustainability and energy efficiency, stimulated by the ambitious EU Energy Efficient Directive and nZEB challenge. The high growth rate of the market share is due to the involvement of homeowners in the specifications of their living commodities, so they are thus willing to invest more at the initial stage to obtain long-term benefits and lower energy exploration costs. We performed an experimental campaign over three slabs with a hydronic radiant floor system of equal dimensions, shape, and pipe pitch with different screed mortar formulations to assess their performance throughout a heating/cooling cycle. The temperature at different heights within the interior of the screed mortars and at the surface were monitored. The results revealed that an improved screed mortar has a relevant impact on the efficiency of the system. Moreover, a three-dimensional transient heat transfer model was validated using the experimental data. The model was used to evaluate the impact of different finishing materials, namely wood, cork, ceramic, and linoleum, on the floor surface temperatures. The results showed differences of 15% in the surface temperature when using different floor finishing solutions.
ABSTRACT
Infrared thermography (IRT) is a technique increasingly used in building inspection. If in many applications it is sufficient to analyze the thermal patterns, others exist in which the exact determination of the surface temperature is a fundamental aspect. In these circumstances, the emissivity of the surfaces assumes special relevance, being probably the most important property in the definition of the boundary conditions. However, information on the uncertainty involved in its measurement, as well as the conditions that influence it, is scarce. This article presents an innovative contribution both to the characterization of the emissivity of various construction materials, and to the discussion of emissivity measurement procedures and the attendant uncertainty. In this sense, three experimental campaigns were carried out: T.I, preliminary tests to assess the initial conditions required for an accurate IRT measurement of the emissivity (reference tape and position of the camera); T.II, assessment of the emissivity of nine different building materials, in dry conditions, using the emissometer and the IRT and black tape methods; and T.III, assessment of the emissivity of three materials during the drying process. The results confirmed that emissivity is a crucial parameter for the accurate measurement of surface temperature. Emissivity measurements carried out with IRT (black tape method) and with the emissometer returned meaningful differences when compared with the values available in the literature. This disagreement led to surface temperature differences of up to 7 °C (emissometer versus reference values). This research also highlighted that the moisture content of the materials influences the emissivity values, with fluctuations that can be greater than 10%, and that the effect of moisture is visible even for low values of moisture content.
ABSTRACT
Moisture is one of the major causes of problems in buildings, and it can compromise their performance. Infrared thermography (IRT) is a non-destructive testing technology that can be used to assess the humidification phenomenon and, thus, prevent some of the problems caused by moisture. The images obtained by IRT reflect the thermal patterns of the surface under study and can be evaluated using a quantitative approach, which allows not only the traditional visualization of the thermal patterns but also quantification of surface temperatures and/or their differences. The relevance of this work is related to the discussion of the strengths and weaknesses of several methods to quantitatively assess the humidification phenomenon using IRT. For that purpose, the partial humidification by the bottom surface of a lightweight concrete specimen was considered as a case study. To evaluate the thermal gradients, the evolution of the thermal imaging throughout the measurement period and the definition of the areas particularly affected by moisture, a methodology that included a pre-processing phase for data reduction, followed by a data processing phase, were implemented. In the data processing, different statistical and numerical methods were tested. The results of the statistical descriptive analysis highlighted the time variation of the surface temperature, both when considering the entire specimen and when considering only specific areas. The variability of the temperatures at certain moments of the experiment could be observed in the box-plot representation. The image subtraction proved to be an interesting technique to quantify the temperature differences if the first image was used as reference. A thermal index, TI, was proposed to assess the cooling rate. The index highlighted the initial instant when the effect of moisture on the surface temperature was detectable.
