Tensile Deformation and Fracture of Unreinforced AZ91 and Reinforced AZ91-C at Temperatures up to 300 °C.

Magnesium alloys are still attractive materials for applications that necessitate light weight due to their low density, moderate strength, and good corrosion resistance. AZ91 is one of the widely applied magnesium alloys due to its very good castability and strength. However, one of the drawbacks of magnesium alloys is the low elastic modulus. So, reinforcing AZ91 with carbon short fibers with the aim of further increasing the strength and improving the elastic modulus is investigated in this study. Squeeze cast AZ91-23 vol.% carbon short carbon (AZ91-C) and the unreinforced AZ91 are deeply examined by tensile testing at different temperatures (20, 100, 150, 200, 250, and 300 °C). Tensile stress-strain curves are measured and the tensile parameters (yield stress, ultimate tensile strength and strain) are defined and presented against the test temperature. Yield stress of AZ91 at 20 °C (109 MPa) is doubled (226 MPa) in the reinforced AZ91-C. Yield stress is found to slightly decrease with increasing the test temperature. Ultimate tensile strength of AZ91 at 20 °C (198 MPa) is increased (262 MPa) in the reinforced AZ91-C. The improvement of the ultimate tensile strength due to reinforcing increases with increasing the test temperature. Flow curves are determined and described by a modified Mecking-Kocks relationship and the flow parameters are determined and described as a function of the test temperature. Microstructure investigation was undertaken of the fractured tensile specimens at the grain boundaries rich in eutectic structure formed at the grain boundaries. Mixed brittle/ductile fracture mode is detected on the fracture surface of unreinforced AZ91, while the SEM investigations show matrix/carbon fiber detachment and fiber fracture as main fracture modes.

Mathematical inspection of heat transfer and unsteady viscous flow in a tunnel with trapezoidal shaped slender wall.

An exploration is made to investigate numerically and theoretically the time dependent flow of blood along with heat transfer through abnormal artery having trapezoidal shaped plaque. The flow is taken to be Newtonian, laminar, unsteady and incompressible. A suitable geometrical model is constructed to simulate the trapezoidal stenosis affected artery. The governed 2-dimensional momentum and heat transfer equations are conventionalized by assuming mild trapezoidal stenosis. The renovate partial differential equations are further converted into ordinary differential equations by assist of transformations. The novelty of the work is to consider unsteady blood flow through trapezoidal shape stenosed artery. A technique of finite difference is used to discretize the updated dimensionless model numerically. Comprehensive graphical outcomes for a flow of blood are obtained. The effect of trapezoidal plaque on blood velocity, pressure and temperature are shown by surface graph inside the artery and also shown with the help of line graph.

Fabrication and Optimisation of Ti-6Al-4V Lattice-Structured Total Shoulder Implants Using Laser Additive Manufacturing.

This work aimed to study one of the most important challenges in orthopaedic implantations, known as stress shielding of total shoulder implants. This problem arises from the elastic modulus mismatch between the implant and the surrounding tissue, and can result in bone resorption and implant loosening. This objective was addressed by designing and optimising a cellular-based lattice-structured implant to control the stiffness of a humeral implant stem used in shoulder implant applications. This study used a topology lattice-optimisation tool to create different cellular designs that filled the original design of a shoulder implant, and were further analysed using finite element analysis (FEA). A laser powder bed fusion technique was used to fabricate the Ti-6Al-4V test samples, and the obtained material properties were fed to the FEA model. The optimised cellular design was further fabricated using powder bed fusion, and a compression test was carried out to validate the FEA model. The yield strength, elastic modulus, and surface area/volume ratio of the optimised lattice structure, with a strut diameter of 1 mm, length of 5 mm, and 100% lattice percentage in the design space of the implant model were found to be 200 MPa, 5 GPa, and 3.71 mm-1, respectively. The obtained properties indicated that the proposed cellular structure can be effectively applied in total shoulder-replacement surgeries. Ultimately, this approach should lead to improvements in patient mobility, as well as to reducing the need for revision surgeries due to implant loosening.