ABSTRACT
BACKGROUND AND OBJECTIVE: The laser debonding procedure of adhesively luted all-ceramic restorations is based on the ablation of resin cement due to the transmitted laser energy through the ceramic. The purpose of this study was to determine the effect of Er:YAG laser irradiation transmitted through a dental ceramic on five different resin cements. MATERIALS AND METHODS: Five different resin cements were evaluated in this study: G-Cem LinkAce, Multilink Automix, Variolink II, Panavia F, and Rely X Unicem U100. Disc shaped resin cement specimens (n = 10) were fabricated for each group. A ceramic disc was placed between the resin cement discs and the tip of the handpiece of Er:YAG laser device. The resin cement discs were irradiated through the ceramic and the volume of the resin cement discs were measured using a micro-CT system before and after Er:YAG laser irradiation. The volume loss of the resin cement discs was calculated and analyzed with one-way ANOVA and Tukey-HSD tests. RESULTS: The highest volume loss was determined in G-Cem (1.1 ± 0.6 mm3 ) and Multilink (1.3 ± 0.1 mm3 ) (P < 0.05) groups, and the lowest volume loss was determined in Rely X (0.3 ± 0.07 mm3 ), Variolink (0.4 ± 0.2 mm3 ), and Panavia (0.6 ± 0.2 mm3 ) groups (P < 0.05). All resin cements were affected by the laser irradiation resulting in the volume loss of the cement; however, there are significant differences among different resin cements. CONCLUSIONS: All the resin cements tested in this study were effected by the Er:YAG laser irradiation and there were significant differences among the resin cements with regard to ablation volume. Lasers Surg. Med. 47:602-607, 2015. © 2015 Wiley Periodicals, Inc.
ABSTRACT
PURPOSE: This study evaluated the effect of four resin cements on the shear bond strength of a ceramic core material to dentin. MATERIALS AND METHODS: One hundred twenty molar teeth were embedded in a self-curing acrylic resin. The occlusal third of the crowns were sectioned under water cooling. All specimens were randomly divided into four groups of 30 teeth each according to the resin cement used. One hundred twenty cylindrical-shaped, 2.7-mm wide, 3-mm high ceramic core materials were heat-pressed. The core cylinders were then luted with one of the four resin systems to dentin (Super-Bond C&B, Chemiace II, Variolink II, and Panavia F). Half of the specimens (n = 15) were tested after 24 hours; the other half (n = 15) were stored in distilled water at 37 degrees C for 1 day and then thermocycled 1000 times between 5 degrees C and 55 degrees C prior to testing. Shear bond strength of each specimen was measured using a universal testing machine at a crosshead speed of 1 mm/min. The bond strength values were calculated in MPa, and the results were statistically analyzed using a two-way analysis of variance (ANOVA) and Tukey HSD tests. RESULTS: The shear bond strength varied significantly depending on the resin cement used (p < 0.05). The differences in the bond strengths after thermocycling were not remarkable as compared with the corresponding prethermal cycling groups (p > 0.05). Significant interactions were present between resin cement and thermocycling (p < 0.05). After 24 hours, the specimens luted with Variolink II (5.3 +/- 2.2 MPa) showed the highest shear bond strength, whereas the specimens luted with Chemiace II (1.6 +/- 0.4 MPa) showed the lowest. After thermocycling, the bond strength values of specimens luted with Chemiace II (1.1 +/- 0.1 MPa) and Super-Bond C&B (1.7 +/- 0.4 MPa) decreased; however, this was not statistically significant (p > 0.05). The increase in the shear bond strength values in the Panavia F (4.5 +/- 0.7 MPa) and Variolink II (5.5 +/- 2.1 MPa) groups after thermocycling was also not statistically significant (p > 0.05). CONCLUSION: Variolink II and Panavia F systems showed higher shear bond strength values than Chemiace II and Super-Bond C&B. They can be recommended for luting ceramic cores to dentin surfaces.
Subject(s)
Dental Bonding , Dental Porcelain/chemistry , Dentin/ultrastructure , Post and Core Technique , Resin Cements/chemistry , Aluminum Silicates/chemistry , Boron Compounds/chemistry , Cementation , Dental Etching , Humans , Materials Testing , Methacrylates/chemistry , Methylmethacrylates/chemistry , Microscopy, Electron, Scanning , Polyethylene Glycols/chemistry , Polymethacrylic Acids/chemistry , Shear Strength , Stress, Mechanical , Surface Properties , Temperature , Time Factors , Water/chemistryABSTRACT
Laser etching has an effect on the mineral content of dentin. The aim of this study was to evaluate the mineral content of dentin prepared at three different power settings with an erbium, chromium:yttrium scandium gallium garnet (Er,Cr:YSGG) laser. The enamel of five, lower, wisdom, molar teeth was removed to expose the dentin surface. Four dentin slabs were obtained, then each tooth was randomly divided into four portions (groups 1 W, 2 W, 3 W and control) so that we could evaluate the effect of laser treatment. The Er,Cr:YSGG laser used for the study had a pulse duration of 140 micros, a pulse repetition rate of 20 Hz and a power output range of 0 W to 6 W. Laser energy was delivered through a fiberoptic system to a sapphire tip terminal 6 mm long and 600 microm in diameter, using a non-contact mode. The levels of five elements: magnesium (Mg), phosphorus (P), calcium (Ca), potassium (K), and sodium (Na), in each slab were measured by inductively coupled plasma-atomic emission spectrometry (ICP-AES). There were significant differences between the groups (1 W, 2 W, 3 W and control) for Ca, Mg, Na, P and Ca/P ratio (P<0.05); however, there were no significant differences for K (P=0.43). Laser treatment at 1 W significantly affected the mean percentage weight of all element groups except K. Scanning electron microscopy (SEM) photographs indicated that the surface irregularities increased with increasing power setting.
