Effect of permeable biofilm on micro- and macro-scale flow and transport in bioclogged pores.

Simulations of coupled flow around and inside biofilms in pores were conducted to study the effect of porous biofilm on micro- and macro-scale flow and transport. The simulations solved the Navier-Stokes equations coupled with the Brinkman equation representing flow in the pore space and biofilm, respectively, and the advection-diffusion equation. Biofilm structure and distribution were obtained from confocal microscope images. The bulk permeability (k) of bioclogged porous media depends on biofilm permeability (kbr) following a sigmoidal curve on a log-log scale. The upper and lower limits of the curve are the k of biofilm-free media and of bioclogged media with impermeable biofilms, respectively. On the basis of this, a model is developed that predicts k based solely on kbr and biofilm volume ratio. The simulations show that kbr has a significant impact on the shear stress distribution, and thus potentially affects biofilm erosion and detachment. The sensitivity of flow fields to kbr directly translated to effects on the transport fields by affecting the relative distribution of where advection and diffusion dominated. Both kbr and biofilm volume ratio affect the shape of breakthrough curves.

Systematic analysis of micromixers to minimize biofouling on reverse osmosis membranes.

Micromixers, UV-curable epoxy traces printed on the surface of a reverse osmosis membrane, were tested on a cross-flow system to determine their success at reducing biofouling. Biofouling was quantified by measuring the rate of permeate flux decline and the median bacteria concentration on the surface of the membrane (as determined by fluorescence intensity counts due to nucleic acid stains as measured by hyperspectral imaging). The micromixers do not appear to significantly increase the pressure needed to maintain the same initial permeate flux and salt rejection. Chevrons helped prevent biofouling of the membranes in comparison with blank membranes. The chevron design controlled where the bacteria adhered to the membrane surface. However, blank membranes with spacers had a lower rate of permeate flux decline than the membranes with chevrons despite having greater bacteria concentrations on their surfaces. With better optimization of the micromixer design, the micromixers could be used to control where the bacteria will adhere to the surface and create a more biofouling resistant membrane that will help to drive down the cost of water treatment.

Colloid dispersion in a uniform-aperture fracture.

This research investigates the dispersion of colloids through fracture systems by exploring experimentally and numerically the transport and dispersion of 1.0-, 0.11-, and 0.043-mum diameter fluorescent carboxylate-modified microspheres and chloride at various flow rates through variable-length, synthetic Plexiglas fractures (flow cells). A dimensionless number describing each experiment is varied by changing the colloid size, flow rate, and fracture length. Surface characteristics of the microspheres and Plexiglas favor repulsive interactions, thereby minimizing the chance of colloid filtration and remobilization. Full recovery of the colloids is typically observed, thereby supporting the assumption of negligible colloid filtration. In comparison to chloride transport, there is increased tailing for colloid plumes traveling through the flow cell. This increased tailing is attributed to Taylor dispersion phenomena (dispersion due to an advection gradient). In the synthetic fractures investigated here, colloid dispersion due to the velocity gradient is evident, but fully developed Taylor conditions are not realized. A particle-tracking algorithm is run inversely to estimate the effective dispersion rate for the colloid plume in each experiment as a function of the experimental parameters (flow rate, fracture length, and colloid size). Results suggest that the log of the effective dispersion rate of the colloid plume increases linearly with the log of the dimensionless number comprising experimental parameters.

Evaluation of synchrotron X-ray computerized microtomography for the visualization of transport processes in low-porosity materials.

Synchrotron-source X-ray computerized microtomography (CMT) is evaluated as a method to visualize transport processes. We conclude that CMT is adequate for visualization of transport experiments if the right conditions exist. Namely, 1) not much more than one-order-of-magnitude range in concentration data is needed for the study, 2) the pore space in the samples are greater than approximately 2--50 mum, depending on the sample size and system setup; 3) the sample is fine-grained enough so that a representative elemental volume (REV) can be contained by a 2--10 mm diameter sample, and 4) the transport process is slow enough that significant changes do not occur within the 25--50 min (and possibly less in the future) needed to collect data for one three-dimensional image. Absorption edge difference imaging (AEDI) in association with CMT is introduced as a method to enhance pore-space visualization. We successfully imaged the pore space in a low-porosity granodiorite, diorite and fine-grained granite cores and a higher-porosity soil aggregate sample. We found that the pore space important to transport in the core samples was smaller than what we were able to visualize with CMT. We also made rudimentary associations of minerals with pore-space location.

Characterization of adsorption sites on aggregate soil samples using synchrotron X-ray computerized microtomography.

Synchrotron-source X-ray computerized microtomography (CMT) was used to evaluate the adsorptive properties of aggregate soil samples. A linear relationship between measured mean mass attenuation coefficient (sigma) and mass fraction iron was generated by imaging mineral standards with known iron contents. On the basis of reported stoichiometries of the clay minerals and identifications of iron oxyhydroxides (1), we calculated the mass fraction iron and iron oxyhydroxide in the intergranular material. The mass fractions of iron were estimated to range from 0.17 to 0.22 for measurements made at 18 keV and from 0.18 to 0.21 for measurements made at 26 keV. One aggregate sample also contained regions within the intergranular material with mass fraction iron ranging from 0.29 to 0.31 and from 0.33 to 0.36 for the 18 and 26 keV measurements, respectively. The mass fraction iron oxyhydroxide ranged from 0.18 to 0.35 for the low-iron intergranular material and from 0.40 to 0.59 for the high-iron intergranular material. Using absorption edge difference imaging with CMT, we visualized cesium on the intergranular material, presumably because of adsorption and possible exchange reactions. By characterizing the mass fraction iron, the mass fraction iron oxyhydroxide, and the adsorptive capacity of these soil mineral aggregates, we provide information useful for conceptualization, development, and parametrization of transport models.

Use of X-ray absorption imaging to examine heterogeneous diffusion in fractured crystalline rocks.

Heterogeneous diffusion in different regions of a fractured granodiorite from Japan has been observed and measured through the use of X-ray absorption imaging. These regions include gouge-filled fractures, recrystallized fracture-filling material and hydrothermally altered matrix. With the X-ray absorption imaging technique, porosity, relative concentration, and relative mass of an iodine tracer were imaged in two dimensions with a sub-millimeter pixel size. Because portions of the samples analyzed have relatively low porosity values, imaging errors can potentially impact the results. For this reason, efforts were made to better understand and quantify this error. Based on the X-ray data, pore diffusion coefficients (Dp) for the different regions were estimated assuming a single diffusion rate and a lognormal multirate distribution of Dp. Results show Dp for the gouge-filled fractures are over an order of magnitude greater than those of the recrystallized fracture-filling material, which in turn is approximately two times greater than those for the altered matrix. The recrystallized fracture-filling material was found to exhibit the greatest degree of variability. The results of these experiments also provide evidence that diffusion from advective zones in fractures through the gouge-filled fractures and recrystallized fracture-filling material could increase the pore space available for matrix diffusion. This evidence is important for understanding the performance of potential nuclear waste repositories in crystalline rocks as diffusion is thought to be an important retardation mechanism for radionuclides.