Disordered spontaneously buckled optical gratings for improved lighting applications.

Technologies for directing daylight deeper within a building space are highly sought after for energy efficiency applications in order to offset artificial lighting costs and to improve workplace productivity via the use of natural light. Vertical window coatings that can perform this task by redistributing sunlight deeper into a space are especially attractive as they are significantly more straightforward to incorporate into a wide variety of architectures as well as to retrofit into existing facades as compared to roof-based skylights or bulky horizontal daylight shelf-type options. The potential energy savings are even greater when one takes into account the fact that such technologies would mitigate harsh glare, allowing window shades to be open for longer portions of the day. However, low-cost and readily scalable techniques are essential for widespread adoption of these window coating technologies. Here, we describe a potentially low-cost method to create a window coating that could enhance daylight penetration, requiring only a thin film of polymeric material deposited on an elastomeric substrate. The resulting structure is a disordered, spontaneously buckled optical grating that spreads incident light without noticeable chromatic dispersion due to its stochastic patterning. The described method has the potential to improve energy efficiency while maintaining acceptable optical clarity.

An in situ tribometer for measuring friction and wear of polymers in a high pressure hydrogen environment.

High pressure hydrogen effects on the friction and wear of polymers are of importance to myriad applications. Of special concern are those used in the infrastructure for hydrogen vehicle refueling stations, including compressor sliding seals, valves, and actuators. While much is known about potentially damaging embrittlement effects of hydrogen on metals, relatively little is known about the effects of high pressure hydrogen on polymers. However, based on the limited results that are published in the literature, polymers also apparently exhibit compatibility issues with hydrogen. An additional study is needed to elucidate these effects to avoid incompatibilities either through design or material selection. As part of this effort, we present here in situ high pressure hydrogen studies of the friction and wear on example polymers. To this end, we have built and demonstrated a custom-built pin-on-flat linear reciprocating tribometer and demonstrated its use with in situ studies of friction and wear behavior of nitrile butadiene rubber polymer samples in 28 MPa hydrogen. Tribology results indicate that friction and wear is increased in high pressure hydrogen as compared both with values measured in high pressure argon and ambient air conditions.

Fabrication of Periodic Gold Nanocup Arrays Using Colloidal Lithography.

Within recent years, the field of plasmonics has exploded as researchers have demonstrated exciting applications related to chemical and optical sensing in combination with new nanofabrication techniques. A plasmon is a quantum of charge density oscillation that lends nanoscale metals such as gold and silver unique optical properties. In particular, gold and silver nanoparticles exhibit localized surface plasmon resonances-collective charge density oscillations on the surface of the nanoparticle-in the visible spectrum. Here, we focus on the fabrication of periodic arrays of anisotropic plasmonic nanostructures. These half-shell (or nanocup) structures can exhibit additional unique light-bending and polarization-dependent optical properties that simple isotropic nanostructures cannot. Researchers are interested in the fabrication of periodic arrays of nanocups for a wide variety of applications such as low-cost optical devices, surface-enhanced Raman scattering, and tamper indication. We present a scalable technique based on colloidal lithography in which it is possible to easily fabricate large periodic arrays of nanocups using spin-coating and self-assembled commercially available polymeric nanospheres. Electron microscopy and optical spectroscopy from the visible to near-infrared (near-IR) was performed to confirm successful nanocup fabrication. We conclude with a demonstration of the transfer of nanocups to a flexible, conformal adhesive film.

Fabrication of large area flexible nanoplasmonic templates with flow coating.

We describe the development of a custom-built two-axis flow coater for the deposition of polymeric nanosphere monolayers that could be used in the fabrication of large area nanoplasmonic films. The technique described here has the capability of depositing large areas (up to 7 in. × 10 in.) of self-assembled monolayers of polymeric nanospheres onto polyethylene terephthalate (PET) films. Here, three sets of films consisting of different diameters (ranging from 100 to 300 nm) of polymeric nanospheres were used to demonstrate the capabilities of this instrument. To improve the surface wettability of the PET substrates during wet-deposition, we enhanced the wettability by using a forced air blown-arc plasma treatment system. Both the local microstructure, as confirmed by scanning electron microscopy, describing monolayer and multilayer coverage, and the overall macroscopic uniformity of the resultant nanostructured film were optimized by controlling the relative stage to blade speed and nanosphere concentration. We also show using a smaller nanoparticle template that such monolayers can be used to form nanoplasmonic films. As this flow-coating approach is a scalable technique, large area films such as the ones described here have a variety of crucial emerging applications in areas such as energy, catalysis, and chemical sensing.

Adsorption Kinetics in Nanoscale Porous Coordination Polymers.

Nanoscale porous coordination polymers were synthesized using simple wet chemical method. The effect of various polymer surfactants on colloidal stability and shape selectivity was investigated. Our results suggest that the nanoparticles exhibited significantly improved adsorption kinetics compared to bulk crystals due to decreased diffusion path lengths and preferred crystal plane interaction.

Equilibrating nanoparticle monolayers using wetting films.

Monolayers of bimodal gold nanoparticles on silicon are investigated by a combination of microscopy (dry monolayers) and x-ray diffraction (dry and wet monolayers). In the presence of an excess of small particles, the nanoscale packing structure closely resembles the small-particle-rich scenario of the structural crossover transition that has been predicted and also observed with micron-scale hard-sphere colloids. Structural morphology is monitored in situ during monolayer dissolution and reassembly within the thin liquid wetting film. This approach allows investigation of size and solvent effects on nanoparticles in quasi-two-dimensional confinement.

Wetting of liquid-crystal surfaces and induced smectic layering at a nematic-liquid interface: an x-ray reflectivity study.

We report the results of a synchrotron x-ray reflectivity study of bulk liquid-crystal surfaces that are coated by thin wetting films of an immiscible liquid. The liquid-crystal subphase consisted of the nematic or isotropic phase of 4-octyl- 4;{'} -cyanobiphenyl (8CB), and the wetting film was formed by the fluorocarbon perfluoromethylcyclohexane (PFMC), a volatile liquid. The thickness of the wetting film was controlled by the temperature difference DeltaT(micro) between the sample and a reservoir of bulk PFMC, contained within the sealed sample cell. Phase information on the interfacial electron density profiles has been extracted from the interference between the scattering from the PFMC-vapor interface and the surface-induced smectic order of the 8CB subphase. The liquid-crystal side of the nematic-liquid (8CB-PFMC) interface is characterized by a density oscillation whose period corresponds to the smectic layer spacing and whose amplitude decays exponentially toward the underlying nematic subphase. The decay length xi of the smectic amplitude is independent of the PFMC film thickness but increases as the nematic-smectic- A transition temperature T(NA) is approached, in agreement with the longitudinal correlation length xi(parallel) proportional, variant(T-T(NA))(-0.7} for the smectic fluctuations in the bulk nematic. The results indicate that the homeotropic orientation of the 8CB molecules is preferred at the 8CB-PFMC interface and that the observed temperature dependence of the smectic layer growth is consistent with the critical adsorption mechanism. The observed DeltaT(micro) dependence of the PFMC film thickness, L proportional, variant(DeltaT(micro))(-1/3) , implies that PFMC completely wets the 8CB surface and is dominated by the nonretarded dispersion interactions between hydro- and fluorocarbons. The complete wetting behavior of PFMC is nearly independent of the degree of interfacial smectic order in the subphase.

Capillary filling of anodized alumina nanopore arrays.

The filling behavior of a room temperature solvent, perfluoromethylcyclohexane, in approximately 20 nm nanoporous alumina membranes was investigated in situ with small angle x-ray scattering. Adsorption in the pores was controlled reversibly by varying the chemical potential between the sample and a liquid reservoir via a thermal offset, DeltaT. The system exhibited a pronounced hysteretic capillary filling transition as liquid was condensed into the nanopores. These results are compared with Kelvin-Cohan theory, with a modified Derjaguin approximation, as well as with predictions by Cole and Saam.

Capillary wave fluctuations and intrinsic widths of coupled fluid-fluid interfaces: an x-ray scattering study of a wetting film on bulk liquid.

An x-ray specular reflectivity (XR) and off-specular diffuse scattering (XDS) study of the coupled thermal capillary fluctuations and the intrinsic profiles of two interacting fluid-fluid interfaces is presented. The measurements are carried out on complete wetting films of perfluoromethylcyclohexane (PFMC) on the surface of bulk liquid eicosane (C20), as a function of film thickness 30infinity), determined by either the radius of gyration (5.3 A) or the bulk correlation length (4.8 A) of the alkane C20. The intrinsic liquid-vapor interfacial width is sharper (approximately 2 A) and remains essentially constant over the entire probed range of D .

Liquids on topologically nanopatterned surfaces.

We report here surface x-ray scattering studies of the adsorption of simple hydrocarbon liquid films on nanostructured surfaces-silicon patterned by an array of nanocavities. Two different regimes, filling and growing, are observed for the wetting film evolution as a function of the chemical potential offset from the bulk liquid-vapor coexistence. The strong influence of geometrical effects is manifested by a dependence of liquid adsorption in the nanocavities that is stronger than the van der Waals behavior for flat surfaces. The observed dependence is, however, much weaker than predicted for the infinitely deep parabolic cavities, suggesting that the finite-size effects contribute significantly to the observed adsorption behavior.