Effectiveness of a manual test at the beginning of dental school.

INTRODUCTION: This study analysed whether the SAZAMED (Self-assessment for dentistry studies) manual test conducted as an exercise or examination in the first year of dental studies, and the official aptitude test for medical studies (EMS), can predict future performance of dental students. MATERIALS AND METHODS: Students enrolled in the dental curriculum at the University of Basel between 2009/10 and 2019/20 were categorized: Group A conducted the SAZAMED in the third bachelor year (BA) and second master year (MA), group B practiced in the first and third BA and second MA and group C had to pass the test in the first BA with repetition in the third BA and second MA. SAZAMED comprised (i) wire bending, (ii) modelling sphere and cube, (iii) drawing mirror-inverted and (iv) indirect drawing over a mirror. Comparative variables were the EMS per cent rank and test scores in practical-clinical examinations in the third BA and the second MA. RESULTS: Data were available from 329 students over the 10-year period. Repeaters and dropouts had poorer performance in the first BA SAZAMED than students who did not (p < 0.001). Among the four SAZAMED exercises, mirror-inverted drawing was the strongest predictor of future student performance. The official aptitude test EMS correlated with the third BA certificate (p = 0.012), but failed to predict repeaters and dropouts. CONCLUSION: Since academic success was associated with significantly better scores on the first BA SAZAMED, it is considered a predictor and recommended in addition to the official EMS to identify students in need of intervention programmes or who should choose a different field of study.

Biosymbiotic platform for chronic long-range monitoring of biosignals in limited resource settings.

Remote patient monitoring is a critical component of digital medicine, and the COVID-19 pandemic has further highlighted its importance. Wearable sensors aimed at noninvasive extraction and transmission of high-fidelity physiological data provide an avenue toward at-home diagnostics and therapeutics; however, the infrastructure requirements for such devices limit their use to areas with well-established connectivity. This accentuates the socioeconomic and geopolitical gap in digital health technology and points toward a need to provide access in areas that have limited resources. Low-power wide area network (LPWAN) protocols, such as LoRa, may provide an avenue toward connectivity in these settings; however, there has been limited work on realizing wearable devices with this functionality because of power and electromagnetic constraints. In this work, we introduce wearables with electromagnetic, electronic, and mechanical features provided by a biosymbiotic platform to realize high-fidelity biosignals transmission of 15 miles without the need for satellite infrastructure. The platform implements wireless power transfer for interaction-free recharging, enabling long-term and uninterrupted use over weeks without the need for the user to interact with the devices. This work presents demonstration of a continuously wearable device with this long-range capability that has the potential to serve resource-constrained and remote areas, providing equitable access to digital health.

Quality of CAD-CAM inlays placed on aged resin-based composite restorations used as deep margin elevation: a laboratory study.

OBJECTIVES: To assess the impact of the age of resin-based composite (RBC) restorations used for deep margin elevation (DME) on the marginal quality and fracture resistance of inlays. MATERIALS AND METHODS: Permanent human molars with direct RBC restorations, involving the mesial, occlusal, and distal surface (MOD), were allocated to four groups (each n = 12). Half of the teeth underwent thermomechanical loading including 240,000 occlusal load cycles and 534 thermal cycles (TML, 5 °C/55 °C; 49 N, 1.7 Hz). With RBC left in one proximal box as DME, all teeth received MOD inlays, made from lithium disilicate (LDS) or a polymer-infiltrated ceramic network material (PICN). The restored teeth underwent TML including 1.2 million occlusal cyclic loadings and 2673 thermal cycles. The marginal quality was assessed at baseline and after both runs of TML. Load-to-fracture tests were performed. The statistical analysis comprised multiple linear regressions (α = 0.05). RESULTS: Simulated aging of RBC restorations had no significant effect on the marginal quality at the interface between the RBC and the tooth and the RBC and the inlay (p ≥ 0.247). Across time points, higher percentages of non-continuous margin were observed between the inlay and the tooth than between the tooth and the RBC (p ≤ 0.039). The age of the DME did not significantly affect the fracture resistance (p ≥ 0.052). CONCLUSIONS: Artificial aging of RBC restorations used for DME had no detrimental effect on the marginal quality and fracture resistance of LDS and PICN inlays. CLINICAL RELEVANCE: This laboratory study suggests that-in select cases-intact, direct RBC restorations not placed immediately before the delivery of an indirect restoration may be used for DME.

RoBDEMAT: A risk of bias tool and guideline to support reporting of pre-clinical dental materials research and assessment of systematic reviews.

OBJECTIVES: To develop a risk of bias tool for pre-clinical dental materials research studies that aims to support reporting of future investigations and improve assessment in systematic reviews. METHODS: A four-stage process following EQUATOR network recommendations was followed, which included project launch, literature review, Delphi process and the tool finalization. With the support of the European Federation of Conservative Dentistry (EFCD) and the Dental Materials Group of the International Association for Dental Research (DMG-IADR), a total of 26 expert stakeholders were included in the development and Delphi vote of the initial proposal. The proposal was built using data gathered from the literature review stage. During this stage, recent systematic reviews featuring dental materials research, and risk of bias tools found in the literature were comprehensively scanned for bias sources. The experts thus reached a consensus for the items, domains and judgement related to the tool, allowing a detailed guide for each item and corresponding signalling questions. RESULTS: The tool features nine items in total, spread between 4 domains, pertaining to the following types of bias: bias related to planning and allocation (D1), specimen preparation (D2), outcome assessment (D3) and data treatment and outcome reporting (D4). RoBDEMAT, as presented, features signalling questions and a guide that can be used for RoB judgement. Its use as a checklist is preferred over a final summary score. CONCLUSION: RoBDEMAT is the first risk of bias tool for pre-clinical dental materials research, supported and developed by a broad group of expert stakeholders in the field, validating its future use. CLINICAL SIGNIFICANCE: This new tool will contribute the study field by improving the scientific quality and rigour of dental materials research studies and their systematic reviews. Such studies are the foundation and support of future clinical research and evidence-based decisions.

Effect of repeated ultrasonic instrumentation on single-unit crowns: a laboratory study.

OBJECTIVES: This laboratory study aimed to assess the effects of ultrasonic instrumentation, simulating 10 years of supportive periodontal therapy (SPT), on single-unit crowns. MATERIALS AND METHODS: Standardized crowns were fabricated from porcelain-fused-to-metal (PFM) (n = 12), zirconia (ZrO2) (n = 12), lithium disilicate (LDS) (n = 12), feldspar ceramic (FSFC) (n = 6), and polymer-infiltrated ceramic network material (PICN) (n = 6). The crowns, luted on PICN abutments with resin-based luting material (RBLM), and if applicable glass ionomer cement (GILC), underwent thermal cycling and trimonthly ultrasonic instrumentation. After 1 and 10 years of simulated SPT, restoration quality assessments were performed, comprising profilometric surface roughness measurements, marginal integrity evaluations, and scores for luting material remnants and visible cracks. The statistical analysis included multiple logistic regressions with nested designs (α = 0.05). RESULTS: During simulated SPT, bulk fractures (n = 2) and a de-cementation failure (n = 1) of LDS and ZrO2 crowns were observed. No significant change in roughness was detected after 10 years (p = 0.078). Over time, marginal defects increased (p = 0.010), with PFM crowns showing the highest rate of chippings at sites with a narrow shoulder. Fewer marginal defects were detectable on crowns luted with RBLM compared with GILC (p = 0.005). Luting material remnants decreased during SPT (p < 0.001). Ultrasonic instrumentation caused cracks in most crown materials, in particular at sites with a narrow shoulder and in PFM crowns. CONCLUSIONS: Repeated ultrasonic instrumentation may damage single-unit crowns. PFM crowns with a narrow, all-ceramic margin are especially prone to defects. CLINICAL RELEVANCE: Frequent ultrasonic instrumentation of restoration margins of fixed dental prostheses, PFM crowns in particular, ought to be avoided.

Endodontic Treatment in Switzerland. A National Survey

The purpose of this study was to collect information about current treatment protocols of endodontic procedures among general practitioners (GP), endodontically interested practitioners (EI) and endodontic specialists (ES) in Switzerland and to compare them with available endodontic quality guidelines and former surveys. A questionnaire was distributed to 1,522 attendees of two national conferences (Swiss Dental Association, 2015; Swiss Society for Endodontology, 2016) addressing socio-demographic characteristics and specific questions about root canal treatments (RCT) including techniques and materials used. Five hundred and six surveys were collected comprising data of 81.8% GP, 14.4% EI and 3.8% ES (response rate: 33.2%). The majority of respondents was male (59.9%), 40­59 years old (55.9%) with >20 years of clinical experience (54.3%). 498 participants (98.4%) stated to perform RCT. Rubber dam was always used in 52.2% of GP, 69.9% of EI and 89.5% of ES, while never-user accounted for 14.1%. Overall, 63.9% used loupes and 13.7% microscopes (mostly by ES). Rotating instruments were selected in 43.2%, followed by conventional hand-instruments (37.8%) and reciprocating instruments (19%). GP rarely activated irrigants and applied NaOCl in lower concentrations (>0.5­1%) compared to ES. GP preferred lateral compaction (57%), ES performed vertical compaction in 89.5%. 92% completed RCT after two or more visits. The majority of dentists in Switzerland follow the available quality guidelines and the present findings are coherent with internationally published surveys. Nonetheless, discrepancies are still present between daily practice and endodontic quality guidelines, especially with the routine use of rubber dam and working length determination, predominantly within the endodontic non-specialists.

Tempo de mudança: a partida como primeiro estágio da Jornada Mitológica de Mulheres Olímpicas Brasileiras / Times of change: leaving home as the first stage of the Mythological Journey of Brazilian Olympic Women / Tiempo de cambio: la partida como la primera etapa de la Jornada Mitológica de Mujeres Olímpicas Brasileñas

No Brasil, muitas crianças e jovens têm a oportunidade de conhecer diferentes modalidades esportivas. Por vezes, esse contato desperta um encanto pelo esporte, sendo a ele dada uma importância e um significado tão grandes que fazem com que eles o prefiram às atividades comuns para outras pessoas da mesma idade, como brincadeiras, convívio familiar ou escolar. Em busca de melhores condições de treinamento e desenvolvimento, esses futuros atletas, muitas vezes, têm que se distanciar de seu núcleo familiar ainda de forma precoce. Este trabalho buscou investigar como as mulheres olímpicas brasileiras, medalhistas de modalidades coletivas, reconhecem o momento que marcou o início de sua especialização esportiva, exclusivamente aquelas em cuja história consta a marca do distanciamento familiar e da saída de casa. A metodologia do trabalho se ancora nas narrativas biográficas, considerada uma modalidade de história oral. Depois de alcançarem a condição de atleta olímpica, é possível pensar que o chamado para a prática esportiva e o distanciamento precoce de seu núcleo familiar foram os primeiros passos para o que seria o início de sua jornada enquanto atleta.

In Brazil, many children and young people have the opportunity to learn about different sports. This contact often awakens a passion for it and it is sometimes considered of great importance. It then makes them choose sport over others activities common to other people of the same age, such as playtime, family and school contact. As they search for better conditions for sport development, these new athletes often have to distance themselves from their family at an early age. This paper sought to investigate how Brazilian Olympic women, medalists of collective modalities, recognized the moment that marks the beginning of their sporting career, especially the athletes that had to leave their homes. The methodology is anchored in the biographical narratives, considered a modality of oral history. After reaching the Olympic athlete status, it is possible to think that the calling for sports practice and the premature leaving the family nest was the first step towards what would be the beginning of a journey as an athlete.

En Brasil, muchos niños y jóvenes tienen la oportunidad de conocer diferentes modalidades deportivas. En algunos momentos, ese contacto despierta un encanto por el deporte, dando a él una importancia y un significado tan grande que hace que ellos lo prefieran a las actividades comunes para otras personas de la misma edad, como juegos, convivencia familiar o escolar. En busca de mejores condiciones de entrenamiento y desarrollo, esos futuros atletas, muchas veces tienen que distanciarse de su núcleo familiar precozmente. Este trabajo buscó investigar cómo las mujeres olímpicas brasileñas, medallistas de modalidades colectivas, reconocen el momento que marca el inicio de su especialización deportiva, exclusivamente aquellas que en su historia consta la marca del distanciamiento familiar y de la salida de casa. La metodología del trabajo se ancla en las narrativas biográficas, considerada una moda-lidad de historia oral. Después de alcanzar la condición de atleta olímpica, es posible pensar que el llamado para la práctica deportiva y el distanciamiento precoz de su núcleo familiar, fue el primer paso para lo que sería el inicio de su jornada como atleta.

Influence of Pretreatment Methods on the Adhesion of Composite and Polymer Infiltrated Ceramic CAD-CAM Blocks.

PURPOSE: To assess the effect of different surface pretreatments on the shear bond strength of resin luting material on CAD-CAM composite resins and a polymer-infiltrated ceramic network (PICN). MATERIALS AND METHODS: CAD-CAM materials (Brilliant Crios, Cerasmart, Lava Ultimate, VITA Enamic) were subjected to the following pretreatments: no pretreatment; grit blasting; grit blasting + silane; HF etching + silane; tribochemical silica coating + silane; manufacturers' specifications; manufacturers' specifications + silane; manufacturers' specifications using only the manufacturers' products including their recommended luting materials (DuoCem, G-Cem LinkForce, RelyX Ultimate, RelyX Unicem 2). Specimens were luted with resin luting material according to the Swiss shear test design. After six months of water storage, shear bond tests were performed. Data were analyzed with multiple linear regression models and nested models (α = 0.05). RESULTS: Low bond strengths were obtained without pretreatment (Brilliant Crios 3.01 ± 0.54 MPa, Cerasmart 2.66 ± 0.47 MPa, Lava Ultimate 1.76 ± 0.26 MPa, VITA Enamic 2.83 ± 0.63 MPa). Grit blasting achieved high bond strengths across all materials (Brilliant Crios 5.17 ± 0.77 MPa, Cerasmart 4.27 ± 0.50 MPa, Lava Ultimate 3.98 ± 0.54 MPa, VITA Enamic 4.97 ± 0.90 MPa). Silane application tended to decrease bond strengths on CAD-CAM composite resins. Following the manufacturers' specifications and using their recommended materials achieved the highest bond strengths for all materials except Cerasmart (Brilliant Crios 5.75 ± 0.91 MPa, Cerasmart 2.82 ± 0.28 MPa, Lava Ultimate 6.63 ± 0.97 MPa, VITA Enamic 7.09 ± 0.77 MPa). CONCLUSION: Grit blasting and the application of a suitable material primer is a useful pretreatment for the bonding of CAD-CAM composite resins. Silane application on CAD-CAM composite resins may entail drawbacks, possibly owing to the scarcity of silanizable fillers.