Laser-based angle-resolved photoemission spectroscopy with micrometer spatial resolution and detection of three-dimensional spin vector.

We have developed a state-of-the-art apparatus for laser-based spin- and angle-resolved photoemission spectroscopy with micrometer spatial resolution (µ-SARPES). This equipment is realized by the combination of a high-resolution photoelectron spectrometer, a 6 eV laser with high photon flux that is focused down to a few micrometers, a high-precision sample stage control system, and a double very-low-energy-electron-diffraction spin detector. The setup achieves an energy resolution of 1.5 (5.5) meV without (with) the spin detection mode, compatible with a spatial resolution better than 10 µm. This enables us to probe both spatially-resolved electronic structures and vector information of spin polarization in three dimensions. The performance of µ-SARPES apparatus is demonstrated by presenting ARPES and SARPES results from topological insulators and Au photolithography patterns on a Si (001) substrate.

The Effect of Colloidal Silica and Glaze Coatings on the Adhesion of Zirconia with Various Ytrria Concentration.

PURPOSE: This study evaluated the effect of coating traditional and translucent Y-TZP with an industrial nanometric colloidal silica or glaze before or after sintering on the adhesion of zirconia with various ytrria concentration. MATERIALS AND METHODS: Specimens of Y-TZP with 3% and 5% yttria were subdivided into 5 groups (n=10), according to the coating applied and moment of application (before or after Y-TZP sintering): Control (no coating), Colloidal Silica/Sintering, Sintering/Colloidal Silica, Glaze/Sintering, Sintering/ Glaze. Lithium disilicate (LD) was used as positive control. Except for Y-TZP controls, groups were conditioned with silane before cementation with a self-adhesive resin cement. After 24 hours, the shear bond strength and failure analysis were performed. Also, analysis of specimens' surface was accomplished with SEM-EDX. Kruskal-Wallis and Dunn tests were applied to analyze differences between groups (p⟨0.05). RESULTS: Overall, the worst and best values of shear bond strength test were control and glaze after sintering groups. Different morphological and chemical aspects were observed in SEM-EDX analysis. CONCLUSIONS: Coating Y-TZP with colloidal silica showed unsatisfactory results. In 3Y-TZP, the surface treatment associated with the best adhesion values was the application of glaze after zirconia sintering. However, in 5Y-TZP, glaze application can be performed before or after the zirconia sintering to optimize clinical steps.

Pentacene films on Cu(119).

The molecular structure of thin pentacene film grown on a Cu(119) surface has been studied by near-edge X-ray absorption fine structure spectroscopy and scanning tunneling microscopy. The interaction between the π-molecular orbitals delocalized on the aromatic rings and the underlying copper substrate was deduced from XAS spectra. Pentacene molecules arrange with the main axis almost parallel with the Cu terraces according to the measured polarization dependence of the C 1s absorption spectra. For thickness exceeding 4 nm an upright arrangement of the molecules was observed with a dense herringbone-like ordering. The present study thus demonstrates that highly ordered pentacene films can be obtained on a Cu(119) vicinal surface both in a flat orientation for low coverages and in a bulk-like herringbone orientation for higher coverages.

Advanced photoelectric effect experiment beamline at Elettra: A surface science laboratory coupled with Synchrotron Radiation.

We report the main characteristics of the advanced photoelectric effect experiments beamline, operational at Elettra storage ring, featuring a fully independent double branch scheme obtained by the use of chicane undulators and able to keep polarization control in both linear and circular mode. The paper describes the novel technical solutions adopted, namely, (a) the design of a quasiperiodic undulator resulting in optimized suppression of higher harmonics over a large photon energy range (10-100 eV), (b) the thermal stability of optics under high heat load via cryocoolers, and (c) the end station interconnected setup allowing full access to off-beam and on-beam facilities and, at the same time, the integration of users' specialized sample growth chambers or modules.

Femtosecond dynamics in ferromagnetic metals investigated with soft x-ray resonant emission.

We present measurements of the magnetic circular dichroism in x-ray resonant emission in the perpendicular geometry (circularly polarized x rays at normal incidence to the magnetization) for L(2,3) the absorption region in Fe, Co, and Ni metal. The results show that spin-dependent screening of the core hole takes place within the scattering time scale, which is supported by the absence of the effect in ionic systems. This allows an assessment of the time scale for the screening process (up to a few femtoseconds). The process is almost complete within the scattering time for Fe and Co, but this is not the case for the narrow band metal Ni which shows a much slower dynamics.

Low energy electronic excitations in the layered cuprates studied by copper L3 resonant inelastic x-ray scattering.

We have measured the resonant inelastic x-ray scattering (RIXS) spectra at the Cu L3 edge in a variety of cuprates. Exploiting a considerably improved energy resolution (0.8 eV) we recorded significant dependencies on the sample composition and orientation, on the scattering geometry, and on the incident photon polarization. The RIXS final states correspond to two families of electronic excitations, having local (dd excitations) and nonlocal (charge-transfer) character. The dd energy splitting can be estimated with a simple crystal field model. The RIXS at the L3 edge demonstrates here a great potential, thanks to the resonance strength and to the large 2p spin-orbit splitting.

Systematic errors in multi-frequency EIT.

Systematic errors have been measured with a multi-frequency data-collection system operating between 10.24 and 81.92 kHz. The errors were present even though a conventional background measurement on a uniform saline phantom had already been subtracted. Errors due to changes in transimpedance between the calibration and the tissue measurements, cable movement and electrode-skin contact impedance were simulated giving a total systematic error estimate equivalent to a 9% change in tissue conductivity. It was shown that more than 89% of the image was above the total error magnitude, indicating that most of the image revealed true changes in tissue conductivity. In three human subjects, the largest conductivity changes were in two regions, located posteriorly on either side of the midline, and were interpreted as due to the erector spinae muscles. These regions showed increases in conductivity of 73-104%. Identification of other anatomical features was difficult because of the poor spatial resolution of the images.