ABSTRACT
Iron (III) oxide (Fe3O4) and sodium dodecyl sulfate (SDS) coated iron (III) oxide (SDS@Fe3O4) nanoparticles (NPs) were synthesized by the co-precipitation method for application in the catalytic degradation of Rhodamine B (RB) dye. The synthesized NPs were characterized using X-ray diffractometer (XRD), vibrating sample magnetometer (VSM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and Fourier transform infra-red (FT-IR) spectroscopy techniques and tested in the removal of RB. A kinetic study on RB degradation by hydrogen peroxide (H2O2) was carried out and the influence of Fe3O4 and SDS@Fe3O4 magnetic NPs on the degradation rate was assessed. The activity of magnetic NPs, viz. Fe3O4 and SDS@Fe3O4, in the degradation of RB was spectrophotometrically studied and found effective in the removal of RB dye from water. The rate of RB degradation was found linearly dependent upon H2O2 concentration and within 5.0 × 10-2 to 4.0 × 10-1 M H2O2, the observed pseudo-first-order kinetic rates (kobs, s-1) for the degradation of RB (10 mg L-1) at pH 3 and temperature 25 ± 2 °C were between 0.4 and 1.7 × 104 s-1, while in presence of 0.1% w/v Fe3O4 or SDS@Fe3O4 NPs, kobs were between 1.3 and 2.8 × 104 s-1 and between 2.6 and 4.8 × 104 s-1, respectively. Furthermore, in presence of Fe3O4 or SDS@Fe3O4, kobs increased with NPs dosage and showed a peaked pH behavior with a maximum at pH 3. The magnitude of thermodynamic parameters Ea and ΔH for RB degradation in presence of SDS@Fe3O4 were 15.63 kJ mol-1 and 13.01 kJ mol-1, respectively, lowest among the used catalysts, confirming its effectiveness during degradation. Furthermore, SDS in the presence of Fe3O4 NPs and H2O2 remarkably enhanced the rate of RB degradation.
ABSTRACT
The authors describe a method for solvent-free mechano-chemical synthesis of a bioinspired sorbent. A 2D ultra-thin carbon sheet similar to graphene oxide was prepared using a natural waste (onion sheet). The formation of 2D carbon sheets was confirmed by Raman spectroscopy, X-ray photoelectron spectroscopy and ATR-IR. The surface morphology was characterized by field emission scanning electron microscopy and high-resolution tunneling electron microscopy. The carbon sheets were decorated with crystalline MnFe2O4 nanoparticles by solid-state reaction at room temperature. The presence of magnetic particles in the final product was confirmed by vibrating sample magnetometry and electron microscopy. The synergistic effect of carbon sheets and MnFe2O4 led to an enhanced sorption of arsenic species compared to bare carbon sheets or to MnFe2O4 nanoparticles. A column was prepared for the simultaneous preconcentration and determination of trace levels of As(III) and As(V) from water samples. The preconcentration factors are between 900 and 833 for As(III) and As(V) species, respectively. The linearity of the calibration plot ranges from 0.4-10 ng mL-1. The detection limits (at 3σ) for both As(III) and As(V) are 30 pg mL-1. The Student's t values for the analysis of spiked samples are lower than the critical Student's t values at a 95% confidence level. The recoveries from spiked water samples range between 99 and 102.8%. Graphical abstract Schematic representation of the preparation of carbon sheets similar to graphene oxide from onion sheaths after pyrolysis at 800 °C. The prepared carbon sheet-MnFe2O4 composite shows excellent arsenic sorption and preconcentration down to the pg mL-1 concentration.
