ABSTRACT
The inherent colloidal dispersity (due to length, aspect ratio, surface charge heterogeneity) of CNCs, when produced using the typical traditional sulfuric acid hydrolysis route, presents a great challenge when interpreting colloidal properties and linking the CNC film nanostructure to the helicoidal self-assembly mechanism during drying. Indeed, further improvement of this CNC preparation route is required to yield films with better control over the CNC pitch and optical properties. Here we present a modified CNC-preparation protocol, by fractionating and harvesting CNCs with different average surface charges, rod lengths, aspect ratios, already during the centrifugation steps after hydrolysis. This enables faster CNC fractionation, because it is performed in a high ionic strength aqueous medium. By comparing dry films from the three CNC fractions, discrepancies in the CNC self-assembly and structural colors were clearly observed. Conclusively, we demonstrate a fast protocol to harvest different populations of CNCs, that enable tailored refinement of structural colors in CNC films.
ABSTRACT
The preferential orientation of the perovskite (PVK) is typically accomplished by manipulation of the mixed cation/halide composition of the solution used for wet processing. However, for PVKs grown by thermal evaporation, this has been rarely addressed. It is unclear how variation in crystal orientation affects the optoelectronic properties of thermally evaporated films, including the charge carrier mobility, lifetime, and trap densities. In this study, we use different intermediate annealing temperatures Tinter between two sequential evaporation cycles to control the Cs0.15FA0.85PbI2.85Br0.15 orientation of the final PVK layer. XRD and 2D-XRD measurements reveal that when using no intermediate annealing primarily the (110) orientation is obtained, while when using Tinter = 100 °C a nearly isotropic orientation is found. Most interestingly for Tinter > 130 °C a highly oriented PVK (100) is formed. We found that although bulk electronic properties like photoconductivity are independent of the preferential orientation, surface related properties differ substantially. The highly oriented PVK (100) exhibits improved photoluminescence in terms of yield and lifetime. In addition, high spatial resolution mappings of the contact potential difference (CPD) as measured by KPFM for the highly oriented PVK show a more homogeneous surface potential distribution than those of the nonoriented PVK. These observations suggest that a highly oriented growth of thermally evaporated PVK is preferred to improve the charge extraction at the device level.
ABSTRACT
Cellulose nanocrystals (CNCs) possess the ability to form helical periodic structures that generate structural colors. Due to the helicity, such self-assembled cellulose structures preferentially reflect left-handed circularly polarized light of certain colors, while they remain transparent to right-handed circularly polarized light. This study shows that combination with a liquid crystal enables modulation of the optical response to obtain light reflection of both handedness but with reversed spectral profiles. As a result, the nanophotonic systems provide vibrant structural colors that are tunable via the incident light polarization. The results are attributed to the liquid crystal aligning on the CNC/glucose film, to form a birefringent layer that twists the incident light polarization before interaction with the chiral cellulose nanocomposite. Using a photoresponsive liquid crystal, this effect can further be turned off by exposure to UV light, which switches the nematic liquid crystal into a nonbirefringent isotropic phase. The study highlights the potential of hybrid cellulose systems to create self-assembled yet advanced photoresponsive and polarization-tunable nanophotonics.
ABSTRACT
The transfer of heterogeneous photocatalysis applications from the laboratory to real-life aqueous systems is challenging due to the higher density of photocatalysts compared to water, light attenuation effects in water, complicated recovery protocols, and metal pollution from metal-based photocatalysts. In this work, we overcome these obstacles by developing a buoyant Pickering photocatalyst carrier based on green cellulose nanofibers (CNFs) derived from wood. The air bubbles in the carrier were stable because the particle surfactants provided thermodynamic stability and the derived photocatalytic foams floated on water throughout the test period (4 weeks). A metal-free semiconductor photocatalyst, g-C3N4, was facilely embedded inside the foam by mixing the photocatalyst with the air-bubble suspension followed by casting and drying to produce solid foams. When tested under mild irradiation conditions (visible light, low energy LEDs) and no agitation, almost three times more dye was removed after 6 h for the floating g-C3N4-CNF nanocomposite foam, compared to the pure g-C3N4 powder residing on the bottom of a ca. 2 cm-high water pillar. The buoyancy and physicochemical properties of the carrier material were imperative to render escalated oxygenation, high photon utilization, and faster dye degradation. The reported assembly protocol is facile, general, and provides a new strategy for assembling green floating foams that can potentially carry a number of different photocatalysts.
