An Adaptive Elastic Support Seat-Based Magnetorheological Elastomer for Human Body Vibration Reduction.

This paper introduces an electromagnetic structure utilizing the controllable mechanical properties of magnetorheological elastomer (MRE) materials through magnetic flux. An adaptive elastic foundation composed of these materials is explored for vibration reduction and frequency modulation. This study investigates these effects using both a single-mass model and a coupled human-seat model. For objects supported by the adaptive elastic foundation, increasing the magnetic flux enhances the stiffness and damping, thereby significantly reducing the peak response while slightly increasing the resonance frequency. Strategies such as increasing the magnetic flux, reducing the object mass, and minimizing the system's degrees of freedom and internal damping contribute to enhancing the vibration reduction and frequency modulation in the adaptive elastic foundation. The simulation results indicate that for a seated human (weighing between 72.4 kg and 88.4 kg), the adaptive elastic foundation reduces the head peak response by approximately 15.7% and increases the resonance frequency by approximately 3.4% at a magnetic flux of 138 mT.

Vibration reduction of human body biodynamic response in sitting posture under vibration environment by seat backrest support.

Four-degree-of-freedom (4-DOF) human-chair coupling models are constructed to characterize the different contact modes between the head, chest back, waist back and backrest. The seat-to-head transfer ratio (STHT) is used as an evaluation metric for vibration reduction effectiveness. The simulated vibration reduction ratio of the model is close to the experimental results, which proves the validity of the model. The peak STHT is obviously reduced (P < 0.05, T-test) with seat-backrest support. The experiments show that supporting the head ( a 1 , P < 0.05, Wilcoxon matched-pairs signed ranks) has the best vibration reduction effect (21%), supporting the chest back ( a 2 , P < 0.05) has a reduced effect (11%), and supporting the waist back ( a 3 , P < 0.05) has the weakest effect (4%). When the upper torso is in full contact with the backrest, the peak STHT curve and resonance frequency are positively correlated with the contact stiffness of the seat surface and negatively correlated with the contact damping. In order to reduce the seat-to-head transfer ratio, the lowest STHT peak and lowest total energy judgments were proposed as the selection methods for the selection of the contact stiffness and damping of the backrest in two environments (periodic and non-periodic excitation), respectively.

Design and Test of a Spoke-like Piezoelectric Energy Harvester.

With the development of industry IoT, microprocessors and sensors are widely used for autonomously transferring information to cyber-physics systems. Massive quantities and huge power consumption of the devices result in a severe increment of the chemical batteries, which is highly associated with problems, including environmental pollution, waste of human/financial resources, difficulty in replacement, etc. Driven by this issue, mechanical energy harvesting technology has been widely studied in the last few years as a great potential solution for battery substitution. Therefore, the piezoelectric generator is characterized as an efficient transformer from ambient vibration into electricity. In this paper, a spoke-like piezoelectric energy harvester is designed and fabricated with detailed introductions on the structure, materials, and fabrication. Focusing on improving the output efficiency and broadening the pulse width, on the one hand, the energy harvesting circuit is optimized by adding voltage monitoring and regulator modules. On the other hand, magnetic mass is adopted to employ the magnetic field of repulsive and upper repulsion-lower attraction mode. The spoke-like piezoelectric energy harvester suggests broadening the frequency domain and increasing the output performance, which is prepared for wireless sensors and portable electronics in remote areas and harsh environments.

Analysis of Output Performance of a Novel Symmetrical T-Shaped Trapezoidal Micro Piezoelectric Energy Harvester Using a PZT-5H.

In recent years, low-power wireless sensors with high flexibility, portability and computing capability have been extensively applied in areas such as military, medicine and mechanical equipment condition monitoring. In this paper, a novel symmetrical T-shaped trapezoidal micro piezoelectric energy harvester (STTM-PEH) is proposed to supply energy for wireless sensors monitoring the vibrations of mechanical equipment. Firstly, the finite element model (FEM) of the STTM-PEH is established. Secondly, the modal analysis of the T-shaped trapezoidal piezoelectric cantilever beam is carried out by finite element software and its vibration modes are obtained. Additionally, the structural characteristics of the STTM-PEH and the composition of piezoelectric patches are described. Furthermore, the effects of resistance, acceleration coefficient, substrate materials and structural parameters of the output performance of the STTM-PEH are researched. The results indicate that the output power of the STTM-PEH rises first and then falls with a change in resistance, while the output voltage does not increase as resistance increases to a certain extent. Meanwhile, selecting copper as the piezoelectric material of the T-shaped trapezoidal piezoelectric cantilever beam can generate a higher energy output. Finally, how the structural parameters, including piezoelectric patch thickness, substrate thickness and cantilever head length, affect the output performance of the STTM-PEH is studied, which illustrates that the load range of the STTM-PEH can be appropriately broadened by adjusting the length of the cantilever beam head. This research is valuable for designing a novel high performance piezoelectric energy harvester.

A Motion Capturing and Energy Harvesting Hybridized Lower-Limb System for Rehabilitation and Sports Applications.

Lower-limb motion monitoring is highly desired in various application scenarios ranging from rehabilitation to sports training. However, there still lacks a cost-effective, energy-saving, and computational complexity-reducing solution for this specific demand. Here, a motion capturing and energy harvesting hybridized lower-limb (MC-EH-HL) system with 3D printing is demonstrated. It enables low-frequency biomechanical energy harvesting with a sliding block-rail piezoelectric generator (S-PEG) and lower-limb motion sensing with a ratchet-based triboelectric nanogenerator (R-TENG). A unique S-PEG is proposed with particularly designed mechanical structures to convert lower-limb 3D motion into 1D linear sliding on the rail. On the one hand, high output power is achieved with the S-PEG working at a very low frequency, which realizes self-sustainable systems for wireless sensing under the Internet of Things framework. On the other hand, the R-TENG gives rise to digitalized triboelectric output, matching the rotation angles to the pulse numbers. Additional physical parameters can be estimated to enrich the sensory dimension. Accordingly, demonstrative rehabilitation, human-machine interfacing in virtual reality, and sports monitoring are presented. This developed hybridized system exhibits an economic and energy-efficient solution to support the need for lower-limb motion tracking in various scenarios, paving the way for self-sustainable multidimensional motion tracking systems in near future.

Piezoelectric Performance of a Symmetrical Ring-Shaped Piezoelectric Energy Harvester Using PZT-5H under a Temperature Gradient.

With the rapid development of microelectronics technology, low-power electronic sensors have been widely applied in many fields, such as Internet of Things, aerospace, and so on. In this paper, a symmetrical ring-shaped piezoelectric energy harvester (SR-PEH) is designed to provide energy for the sensor to detect the ambient temperature. The finite element method is used by utilizing software COMSOL 5.4, and the electromechanical coupling model of the piezoelectric cantilever is established. The output performance equations are proposed; the microelectromechanical system (MEMS) integration process of the SR-PEH, circuit, and sensor is stated; and the changing trend of the output power density is explained from an energy perspective. In the logarithmic coordinate system, the results indicate that the output voltage and output power are approximately linear with the temperature when the resistance is constant. In addition, the growth rate of the output voltage and output power decreases with an increase of resistance under the condition of constant temperature. In addition, with an increase of temperature, the growth rate of the output power is faster than that of the output voltage. Furthermore, resistance has a more dramatic effect on the output voltage, whereas temperature has a more significant effect on the output power. More importantly, the comparison with the conventional cantilever-shaped piezoelectric energy harvester (CC-PEH) shows that the SR-PEH can improve the output performance and broaden the frequency band.