Optimizing reaction conditions and experimental studies of selective catalytic reduction of NO by CO over supported SBA-15 catalyst.

Selective catalytic reduction of NO with CO (CO-SCR) was investigated based on optimizing the operating conditions by response surface methodology (RSM) and by appropriately choosing the supported SBA-15 catalysts. The effects of the CO-SCR reaction parameters such as NO:CO molar ratios and oxygen concentrations on the catalytic performance were determined by RSM to evaluate the NO conversion using a first-order polynomial model. The CuO/SBA-15 and Fe2O3/SBA-15 catalysts were synthesized by a hydrothermal method and characterized by X-ray diffraction (XRD), atomic absorption spectroscopy (AAS), N2 adsorption-desorption (BET), scanning electron microscopy coupled to energy dispersive X-Ray spectroscopy (SEM-EDS), and Fourier transform infrared spectroscopy (FTIR) to investigate the physicochemical properties of the solids. The RSM showed a very good agreement between predicted values and experimental results with the Pareto analysis confirming the accuracy and reliability of the model. The optimized results indicated the maximum NO conversion at 500 °C with using the NO to CO molar ratio of 1:2 (500:1000 ppm) in the absence of oxygen. Under these conditions, CuO/SBA-15 catalyst achieved 99.7% of NO conversion, whereas Fe2O3/SBA-15 had 98.1% of the catalytic parameter. Catalytic tests in CO-SCR reaction were performed on both catalysts at optimum operating conditions with CuO/SBA-15 exhibiting better performance compared to that of Fe2O3/SBA-15. The results revealed that CuO/SBA-15 was a promising catalyst for CO-SCR of NO due to the well-dispersed CuO phase on SBA-15 surface that allows the solid being more tolerant to the presence of oxygen.

Acid Red 66 Dye Removal from Aqueous Solution by Fe/C-based Composites: Adsorption, Kinetics and Thermodynamic Studies.

The presence of synthetic dyes in water causes serious environmental issues owing to the low water quality, toxicity to environment and human carcinogenic effects. Adsorption has emerged as simple and environmental benign processes for wastewater treatment. This work reports the use of porous Fe-based composites as adsorbents for Acid Red 66 dye removal in an aqueous solution. The porous FeC and Fe/FeC solids were prepared by hydrothermal methods using iron sulfates and sucrose as precursors. The physicochemical properties of the solids were evaluated through X-ray diffraction (XRD), Scanning electron microscopy coupled with Energy dispersive spectroscopy (SEM-EDS), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared s (FTIR), Raman and Mössbauer spectroscopies, nitrogen adsorption-desorption isotherms, Electron Paramagnetic Resonance (EPR) and magnetic saturation techniques. Results indicated that the Fe species holds magnetic properties and formed well dispersed Fe3O4 nanoparticles on a carbon layer in FeC nanocomposite. Adding iron to the previous solid resulted in the formation of γ-Fe2O3 coating on the FeC type structure as in Fe/FeC composite. The highest dye adsorption capacity was 15.5 mg·g-1 for FeC nanocomposite at 25 °C with the isotherms fitting well with the Langmuir model. The removal efficiency of 98.4% was obtained with a pristine Fe sample under similar experimental conditions.

Chitosan/mangiferin particles for Cr(VI) reduction and removal.

In this work, chitosan/mangiferin particles (CMP) were prepared by spray-drying technique and characterized by SEM, DLS, FTIR, HPLC-UV and adsorption studies to investigate a possible application as a preventive material in cases of human and animal contamination with Cr(VI). CMP presented sizes ranging from nano to micrometers. Chitosan and mangiferin (MA) presence in the powder was confirmed by FTIR and MA quantification (136 µg/mg) was performed using a calibration curve prepared by HPLC-UV. Adsorption capacity of Cr(VI) onto CMP was compared with chitosan and investigated in a batch system by considering the effects of various parameters like contact time, initial concentration of adsorbent and pH. Cr(VI) removal is pH dependent and it was found to be maximum at pH 5.0. The results showed that CMP has a potential application as a preventive material in cases of human or animal contamination with Cr(VI).